A 5-bit MMIC serial to parallel converter has been designed in Gallium Arsenide. It is intended to be used together with a 5-bit True Time Delay (TTD) circuit, but it can easily be expanded into an arbitrary number of bits. The circuit has been designed with a logic style called DCFL and a 0.20 mm process (ED02AH) from OMMIC has been used to fabricate the circuit. The chip size of this 5-bit MMIC serial to parallel converter is 2.0x0.8 mm (including pads) and close to two hundred transistors are used. Due to the complexity of the transistor models the complete serial to parallel converter has not been fully simulated. However, the smaller building blocks like inverter, latch, etc. have been simulated successfully. These blocks were assembled into the complete circuit.

<p>A 5-bit MMIC serial to parallel converter has been designed in Gallium Arsenide. It is intended to be used together with a 5-bit True Time Delay (TTD) circuit, but it can easily be expanded into an arbitrary number of bits. The circuit has been designed with a logic style called DCFL and a 0.20 mm process (ED02AH) from OMMIC has been used to fabricate the circuit. The chip size of this 5-bit MMIC serial to parallel converter is 2.0x0.8 mm (including pads) and close to two hundred transistors are used. Due to the complexity of the transistor models the complete serial to parallel converter has not been fully simulated. However, the smaller building blocks like inverter, latch, etc. have been simulated successfully. These blocks were assembled into the complete circuit.</p>

The continual increase of wireless technologies in the world has motivated the use of phased arrays to mitigate radio frequency interference (RFI). There are many methods of performing beamforming for RFI rejection, but they are traditionally physically large and complicated solutions. Phased arrays need to be shrunk and made cheaper for them to see widespread use. This work presents several compact phased array receivers for different applications. The first part of this thesis presents a software GPS processor for a digital beamforming GPS receiver. The receiver is small enough to be flown on drones and enables GPS signals to be processed and a user’s position to be determined. Using digital beamforming, it can operate even under poor conditions such as intentional jamming, RFI, and large multipath effects. Next, this work builds a frontend RF chain for a true time delay phased array receiver. The receiver uses analog true delay delay chips to mitigate radio frequency interference in sensitive instruments. True time delay allows for analog beamforming over a wide bandwidth, but compact true time delay solutions are new and untested. The receiver allows these solutions to be properly vetted in a full system. The chain uses novel compact wideband antennas for L-band frequencies and traditional low cost amplifiers and filters. The last section of this thesis updates the open-source CASPER project to fully support RF system-on-chips. CASPER is an open-source framework for radio astronomy instruments. It speeds up the design and implementation of radio astronomy instruments on compact platforms and makes them easier to interact with. This work expands the framework to use the transmit abilities of advanced RF system-on-chip platforms. With this expansion, full duplex systems such as communications and radar can now also use CASPER. A full loopback beamforming test built on CASPER demonstrates both transmit and receive beamforming.

No description available.

No description available.

True time delay networks are one of the most critical structures of wideband phased-array antenna systems which are frequently used in self-protection and electronic warfare applications. In order to direct the main beam of a wideband phased-array antenna to the desired direction / phase values, which are linearly dependent to frequency, are essential. Due to the phase characteristics of the true-time delay networks, beam squint problems for broadband phased array systems are minimized. In this thesis, different types of true-time delay structures are investigated for wideband phased array applications and a tunable S-band true-time delay network having delay over 1ns with high resolution is developed, designed, fabricated and measured. Lower-cost, smaller occupied area, digital/analog control mechanism and ease of implementation are the other features of the developed network. High delay values with high resolutions for wideband operation are achieved through the combination of several techniques / therefore the desired S-band TTD network is constructed with the synthesis of switched-transmission lines, constant-R networks and periodically-loaded transmission lines. Higher delay states are realized by the switched-transmission lines technique, while the method of constant R-network is used for the intermediate delay states. To increase the tuning flexibility, smaller delay states are accomplished by analog-voltage controlled periodically loaded transmission lines. A step-by-step procedure is followed during the design process of the S-band true time delay network. Firstly, each method used in the TTD network is analyzed in detail and developed for PCB implementation and the use of COTS components. Then, the designed structures are verified via linear and EM simulations performed by ADS2011&reg / . After that, the effects of production tolerances are examined to optimize each design for S-band operations. Moreover, the designed structures are fabricated by using PCB technology and measured. Finally, a software code is developed in MATLAB to generate the overall cascaded network with the help of measured data.

Phased array antenna (PAA) is a key component in many of the modern military and commercial radar and communication systems requiring highly directional beams with narrow beam widths. One of the advantages that this technology offers is a physical movement-free beam steering. Radar and communication technologies also require the PAA systems to be compact, light weight, demonstrate high bandwidth and electromagnetic interference (EMI) free performance. Conventional electrical phase shifters are inherently narrowband. This calls for technologies that have a larger bandwidth and high immunity to electromagnetic interference. Optical true-time-delay (TTD) technique is an emerging technology that is capable of providing these features along with the ability to provide frequency independent beam steering. Photonic crystal fiber (PCF) based optical TTD lines are capable of providing precise and continuous time delays required for PAA systems. Photonic crystal fibers are a new class of optical fibers with a periodic arrangement of air-holes around a core that can be designed to provide extraordinary optical characteristics which are unrealizable using conventional optical fibers. In this dissertation, highly dispersive photonic crystal fiber structures based on index-guidance and bandgap-guidance were designed. Designs exhibiting dispersion coefficients as large as -9500ps/nm/km and 4000ps/nm/km at 1550nm were presented. A TTD module utilizing a fabricated highly dispersive PCF with a dispersion coefficient of -600ps/nm/km at 1550nm was formed and characterized. The module consisted of 4 delay lines employing highly dispersive PCFs connected with various lengths of non-zero dispersion shifted fibers. By employing PCFs with enhanced dispersion coefficients, the TTD module size can be proportionally reduced. A 4-element linear X-band PAA system using the PCF-TTD module was formed and characterized to provide continuous time delays to steer radiofrequency (RF) beams from -41 degrees to 46 degrees by tuning the wavelength from 1530nm to 1560nm. Using the PCF-TTD based X-Band PAA system, single and simultaneous multiple beam transmission and reception capabilities were demonstrated. Noise and distortion performance characteristics of the entire PAA system were also evaluated and device control parameters were optimized to provide maximum spurious-free-dynamic range. In order to alleviate computational and weight requirements of practical large PAA systems, a sparse array instead of a standard array needs to be used. X-Band sparse array systems using PCF and dispersive fiber TTD technique were formed and RF beam steering was demonstrated. As an important achievement during the research work, the design and fabricated structure of a PCF currently reported to have the highest dispersion coefficient of -5400ps/nm/km at 1549nm, along with its limitations was also presented. Finally, other interesting applications of highly dispersive PCFs in the areas of pulse compression and soliton propagation were explored. / text

Recent research focuses on expanding the use of RF/Microwave circuits and systems to include multi-disciplinary applications. One example is the detection of the dielectric properties of chemicals and bio-chemicals at microwave frequencies, which is useful for pharmaceutical applications, food and drug safety, medical diagnosis and material characterization. Dielectric spectroscopy is also quite relevant to detect the frequency dispersive characteristics of materials over a wide frequency range for more accurate detection. In this dissertation, on-chip and on-board solutions for microwave chemical sensing are proposed. An example of an on-chip dielectric detection technique for chemical sensing is presented. An on-chip sensing capacitor, whose capacitance changes when exposed to material under test (MUT), is a part of an LC voltage-controlled oscillator (VCO). The VCO is embedded inside a frequency synthesizer to convert the change in the free runing frequency frequency of the VCO into a change of its input voltage. The system is implemented using 90 nm CMOS technology and the permittivities of MUTs are evaluated using a unique detection procedure in the 7-9 GHz frequency range with an accuracy of 3.7% in an area of 2.5 × 2.5 mm^2 with a power consumption of 16.5 mW. The system is also used for binary mixture detection with a fractional volume accuracy of 1-2%. An on-board miniaturized dielectric spectroscopy system for permittivity detec- tion is also presented. The sensor is based on the detection of the phase difference be- tween the input and output signals of cascaded broadband True-Time-Delay (TTD) cells. The sensing capacitor exposed to MUTs is a part of the TTD cell. The change of the permittivity results in a change of the phase of the microwave signal passing through the TTD cell. The system is fabricated on Rogers Duroid substrates with a total area of 8 × 7.2 cm2. The permittivities of MUTs are detected in the 1-8 GHz frequency range with a detection accuracy of 2%. Also, the sensor is used to extract the fractional volumes of mixtures with accuracy down to 1%. Additionally, multi-band and multi-standard communication systems motivate the trend to develop broadband front-ends covering all the standards for low cost and reduced chip area. Broadband amplifiers are key building blocks in wideband front-ends. A broadband resistive feedback low-noise amplifier (LNA) is presented using a composite cross-coupled CMOS pair for a higher gain and reduced noise figure. The LNA is implemented using 90 nm CMOS technology consuming 18 mW in an area of 0.06 mm2. The LNA shows a gain of 21 dB in the 2-2300 MHz frequency range, a minimum noise figure of 1.4 dB with an IIP3 of -1.5 dBm. Also, a four-stage distributed amplifier is presented providing bandwidth extension with 1-dB flat gain response up to 16 GHz. The flat extended bandwidth is provided using coupled inductors in the gate line with series peaking inductors in the cascode gain stages. The amplifier is fabricated using 180 nm CMOS technology in an area of 1.19 mm2 achieving a power gain of 10 dB, return losses better than 16 dB, noise figure of 3.6-4.9 dB and IIP3 of 0 dBm with 21 mW power consumption. All the implemented circuits and systems in this dissertation are validated, demonstrated and published in several IEEE Journals and Conferences.

Since their discovery in 1978 by Hill et al. and the development of the transverse holographic technique for their fabrication by Meltz et al. in 1989, fiber Bragg gratings (FBG) have become an important device for applications in optical communications, optical signal processing and fiber-optical sensors. A superstructured fiber Bragg grating (SFBG), also called a sampled fiber Bragg grating, is a special FBG that consists of a several small FBGs placed in close proximity to one another. SFBGs have attracted much attention in recent years with the discovery of techniques allowing the creation of equivalent chirp or equivalent phase shifts. The biggest advantage of an SFBG with equivalent chirp or equivalent phase shifts is the possibility to design and fabricate gratings with greatly varying phase and amplitude responses by adjusting the spatial profile of the superstructure. The realization of SFBGs with equivalent chirp or equivalent phase shifts requires only sub-millimeter precision. This is a relief from the sub-micron precision required by traditional approaches. In this thesis, the mathematical modeling of FBGs and SFBGs is reviewed. The use of SFBGs for various applications in photonic microwave signal processing is considered. Four main topics are presented in this thesis. The first topic is the use of SFBG as a photonic true-time delay (TTD) beamformer for phased array antennas (PAAs). The second topic addresses non-linearities in the group delay response of an SFBG with equivalent chirp in its sampling period. An SFBG with an equivalent chirp using only a linear chirp coefficient may yield a group delay response that deviates from the linear response required by a TTD beamformer. In the thesis, a technique to improve the linearity of the group delay response is proposed and an adaptive algorithm to find the optimal linear and non-linear chirp coefficients to produce the best linear group delay response is described. Since no closed-form solution exists to represent the amplitude and phase responses of an SFBG, we rely on a Fourier transform analogy under a weak grating approximation as a starting point in the design of an SFBG. Simulations are then used to refine the response of the SFBG. The algorithm proposed provides an optimal set of chirp coefficients that minimizes the error in the group delay response. Four gratings are fabricated using the optimized chirp coefficients and their application in a TTD PAA system is discussed. The third topic discusses the use of an SFBG with equivalent phase shifts in its sampling period as a means to realize optical single sideband (SSB) modulation. SSB modulation eliminates the power penalty caused by chromatic dispersion experienced by an optical signal traveling through a long length of optical fiber. By introducing two π phase shifts through equivalent sampling to the SFBG, two ultra-narrow transmission bands are created in the grating stop band of the +/- 1st spectral orders. In the proposed system, a double-sideband plus carrier (DSB+C) modulated optical signal is sent to the input of an optical SSB filter based on the equivalent phase-shift SFBG in order to select the optical carrier and a single sideband, effectively blocking one sideband from propagating. Finally, the fourth topic focuses on the implementation of a photonic microwave bandpass filter based on an SFBG with equivalent chirp. Photonic microwave filters are used to process microwave signals in the optical domain. By using a technique called phase-modulation to intensity-modulation (PM-IM) conversion, a two-tap delay line filter is created with one negative tap. A single SFBG with a chirp in its sampling period is used as a means to achieve the PM-IM conversion for the two taps. Two phase modulated optical carriers are used to generate the two taps, each entering a different port of the SFBG and thus experiencing an opposite dispersion value. The two optical signals are then recombined before being sent to a photodetector (PD) where the filtered microwave signal is recovered.

Since their discovery in 1978 by Hill et al. and the development of the transverse holographic technique for their fabrication by Meltz et al. in 1989, fiber Bragg gratings (FBG) have become an important device for applications in optical communications, optical signal processing and fiber-optical sensors. A superstructured fiber Bragg grating (SFBG), also called a sampled fiber Bragg grating, is a special FBG that consists of a several small FBGs placed in close proximity to one another. SFBGs have attracted much attention in recent years with the discovery of techniques allowing the creation of equivalent chirp or equivalent phase shifts. The biggest advantage of an SFBG with equivalent chirp or equivalent phase shifts is the possibility to design and fabricate gratings with greatly varying phase and amplitude responses by adjusting the spatial profile of the superstructure. The realization of SFBGs with equivalent chirp or equivalent phase shifts requires only sub-millimeter precision. This is a relief from the sub-micron precision required by traditional approaches. In this thesis, the mathematical modeling of FBGs and SFBGs is reviewed. The use of SFBGs for various applications in photonic microwave signal processing is considered. Four main topics are presented in this thesis. The first topic is the use of SFBG as a photonic true-time delay (TTD) beamformer for phased array antennas (PAAs). The second topic addresses non-linearities in the group delay response of an SFBG with equivalent chirp in its sampling period. An SFBG with an equivalent chirp using only a linear chirp coefficient may yield a group delay response that deviates from the linear response required by a TTD beamformer. In the thesis, a technique to improve the linearity of the group delay response is proposed and an adaptive algorithm to find the optimal linear and non-linear chirp coefficients to produce the best linear group delay response is described. Since no closed-form solution exists to represent the amplitude and phase responses of an SFBG, we rely on a Fourier transform analogy under a weak grating approximation as a starting point in the design of an SFBG. Simulations are then used to refine the response of the SFBG. The algorithm proposed provides an optimal set of chirp coefficients that minimizes the error in the group delay response. Four gratings are fabricated using the optimized chirp coefficients and their application in a TTD PAA system is discussed. The third topic discusses the use of an SFBG with equivalent phase shifts in its sampling period as a means to realize optical single sideband (SSB) modulation. SSB modulation eliminates the power penalty caused by chromatic dispersion experienced by an optical signal traveling through a long length of optical fiber. By introducing two π phase shifts through equivalent sampling to the SFBG, two ultra-narrow transmission bands are created in the grating stop band of the +/- 1st spectral orders. In the proposed system, a double-sideband plus carrier (DSB+C) modulated optical signal is sent to the input of an optical SSB filter based on the equivalent phase-shift SFBG in order to select the optical carrier and a single sideband, effectively blocking one sideband from propagating. Finally, the fourth topic focuses on the implementation of a photonic microwave bandpass filter based on an SFBG with equivalent chirp. Photonic microwave filters are used to process microwave signals in the optical domain. By using a technique called phase-modulation to intensity-modulation (PM-IM) conversion, a two-tap delay line filter is created with one negative tap. A single SFBG with a chirp in its sampling period is used as a means to achieve the PM-IM conversion for the two taps. Two phase modulated optical carriers are used to generate the two taps, each entering a different port of the SFBG and thus experiencing an opposite dispersion value. The two optical signals are then recombined before being sent to a photodetector (PD) where the filtered microwave signal is recovered.