Wireless Sensor Networks have found diverse applications from health to agriculture and industry. They have a potential to profound social changes, however, there are also some challenges that have to be addressed. One of the problems is the limited power source available to energize a sensor node. Longevity of a node is tied to its low power design. One of the areas where great power savings could be made is in nodal communication. Different schemes have been proposed targeting low power communication and short network latency. One of them is the introduction of ultra-low power wake-up receiver for monitoring the channel. Although it is a recent proposal, there has been many works published. In this thesis work, the focus is study and comparison of architectures for a wake-up receiver. As part of this study, an envelope detector based wake-up receiver is designed in 130nm CMOS Technology. It has been implemented in schematic and layout levels. It operates in the 2.4GHz ISM band and consumes a power consumption of 69µA at 1.2V supply voltage. A sensitivity of -52dBm is simulated while receiving 100kb/s OOK modulated wake-up signals. / This is a master's thesis work by a communication electronics student in a German company called IMST GmbH.

Les Réseaux de Capteurs Sans Fils (RCSFs) sont composés d'une multitude de nœuds, chacun étant capable de réaliser des mesures (température, pression, etc) et de communiquer par radio fréquence. Ces réseaux forment une pierre angulaire de l'Internet des Objets, en étant au cœur de nombreuses applications, par exemple de domotique ou d'agriculture de précision. La limite d'utilisation des RCSFs provient souvent de leurs durées de vie restreintes, les rendant peu intéressants pour des applications nécessitants de longues périodes de fonctionnement en autonomie. En effet, les RCSFs traditionnels sont alimentés par des piles individuelles équipant chaque nœud, et les nœuds sont ainsi condamnés à une durée de vie finie et courte par rapport aux besoins de certaines applications. De plus, changer les piles n'est pas toujours réalisable si le réseau est dense, ou si les nœuds sont déployés dans des environnements les rendant difficile d'accès. Une solution plus prometteuse est d'équiper chaque nœud d'un ou de plusieurs récupérateur(s) d'énergie individuel(s), et ainsi de le rendre capable de s'alimenter exclusivement à partir de l'énergie récoltée dans son environnent. Plusieurs sources d'énergie sont possibles, telles que le vent ou le solaire. Étant donné que les sources d'énergie sont typiquement dynamiques et non contrôlées, ne pas tomber en panne d'alimentation et nécessaire pour garantir un fonctionnement fiable. Comme l'augmentation de la qualité de service engendre souvent une augmentation de la puissance consommée, une solution simple est de configurer la qualité de service au déploiement à une valeur constante suffisamment faible pour éviter la panne d'alimentation. Cependant, cette solution ne permet pas d'exploiter pleinement l'énergie récoltée, et mène ainsi à un gaspillage d'énergie important ainsi qu'à de faibles qualités de service au vu de l'énergie récoltée. Une solution plus efficace est d'adapter dynamiquement la puissance consommée, et donc la qualité de service. Cette adaptation est faite par un composant logiciel appelé gestionnaire d'énergie. Dans cette thèse, deux nouvelles approches pour l'adaptation en ligne sont proposées, l'une s'appuyant sur la théorie du contrôle floue, et l'autre sur l'apprentissage par renforcement. De plus, comme la communication est souvent la tâche la plus énergivore dans les RCSFs, les wake-up receivers sont utilisées dans cette thèse pour réduire le coût des communications. Un modèle analytique générique a été proposé pour étudier différents protocoles de contrôle d'accès au support (Medium Access Control -- MAC), et combiné à des résultats expérimentaux pour évaluer les wake-up receivers. Aussi, un nouveau protocole MAC permettant la sélection opportuniste de relais a été proposé. Enfin, la combinaison des wake-up receivers et de la récolte d'énergie a été étudiée expérimentalement avec un cas pratique. / Wireless Sensor Networks (WSNs) are made of multiple sensor devices which measure physical value (e.g. temperature, pressure...) and communicate wirelessly. These networks form a key enabling technology of many Internet of Things (IoT) applications such as smart building and precision farming. The bottleneck of long-term WSN applications is typically the energy. Indeed, traditional WSNs are powered by individual batteries and a significant effort was devoted to maximizing the lifetime of these devices. However, as the batteries can only store a finite amount of energy, the network is still doomed to die, and changing the batteries is not always possible if the network is dense or if the nodes are deployed in a harsh environment. A promising solution is to enable each node to harvest energy directly in its environment, using individual energy harvesters. As most of the energy sources are dynamic and uncontrolled, avoiding power failures of the nodes is critical to enable reliable networks. Increasing the quality of service typically requires increasing the power consumption, and a simple solution is to set the quality of service of the nodes to a constant value low enough to avoid power failures. However, this solution does not fully exploits the available energy and therefore leads to high energy waste and poor quality of service regarding the available environmental energy. A more efficient solution is online adaptation of the node power consumption, which is performed by an energy manager on each node. In this thesis, two new approaches for online adaptation of the nodes energy consumption were proposed, relying on fuzzy control theory and reinforcement learning. Moreover, as communications are typically the most energy consuming task of a WSN node, emerging wake-up receivers were leveraged to reduce the energy cost of communications. A generic analytical framework for evaluating Medium Access Control (MAC) protocols was proposed, and it was combined to experiments to evaluate emerging wake-up receivers. A new opportunistic MAC protocol was also introduced for "on-the-fly" relay selection. Finally wake-up receivers and energy harvesting were combined and experimentally evaluated in a practical use case.

The influence of depolarization and its role in causing data retention failure in ferroelectric memories is investigated. Ferroelectric Hf₀.₅Zr₀.₅O₂ thin films 8 nm thick incorporated into a metal-ferroelectric-metal capacitor are fabricated and characterized with varying thicknesses of an Al₂O₃ interfacial layer. The magnitude of the depolarization field is adjusted by controlling the thickness of the Al₂O₃ layer. The initial polarization and the change in polarization with electric field cycling is strongly impacted by the insertion of Al₂O₃ within the device stack. Transient polarization loss is shown to get worse with larger depolarization fields and data retention is evaluated up to 85 °C.

The Internet of Things (IoT) is leading the world to the Internet of Everything (IoE), where things, people, intelligent machines, data and processes will be connected together. The key to enter the era of the IoE lies in enormous sensor nodes being deployed in the massively expanding wireless sensor networks (WSNs). By the year of 2025, more than 42 billion IoT devices will be connected to the Internet. While the future IoE will bring priceless advantages for the life of mankind, one challenge limiting the nowadays IoT from further development is the ongoing power demand with the dramatically growing number of the wireless sensor nodes. To address the power consumption issue, this dissertation is motivated to investigate low-power wake-up receivers (WuRXs) which will significantly enhance the sustainability of the WSNs and the environmental awareness of the IoT. Two proof-of-concept low-power WuRXs with focuses on two different application scenarios have been proposed. The first WuRX, implemented in a cost-effective 180-nm CMOS semiconductor technology, operates at 401−406-MHz band. It is a good candidate for application scenarios, where both a high sensitivity and an ultra-low power consumption are in demand. Concrete use cases are, for instance, medical implantable applications or long-range communications in rural areas. This WuRX does not rely on a further assisting semiconductor technology, such as MEMS which is widely used in state-of-the-art WuRXs operating at similar frequencies. Thus, this WuRX is a promising solution to low-power low-cost IoT. The second WuRX, implemented in a 45-nm RFSOI CMOS technology, was researched for short-range communication applications, where high-density conventional IoT devices should be installed. By investigation of the WuRX for operation at higher frequency band from 5.5 GHz to 7.5 GHz, the nowadays ever more over-traffic issues that arise at low frequency bands such as 2.4 GHz can be substantially addressed. A systematic, analytical research route has been carried out in realization of the proposed WuRXs. The thesis begins with a thorough study of state-of-the-art WuRX architectures. By examining pros and cons of these architectures, two novel architectures are proposed for the WuRXs in accordance with their specific use cases. Thereon, key WuRX parameters are systematically analyzed and optimized; the performance of relevant circuits is modeled and simulated extensively. The knowledge gained through these investigations builds up a solid theoretical basis for the ongoing WuRX designs. Thereafter, the two WuRXs have been analytically researched, developed and optimized to achieve their highest performance. Proof-of-concept circuits for both the WuRXs have been fabricated and comprehensively characterized under laboratory conditions. Finally, measurement results have verified the feasibility of the design concept and the feasibility of both the WuRXs.

abstract: The piece WAKE UP BREATHING holds personal significance as an investigation of thought-provoking issues of breathing through film installation, video and live performance. This research specifically addressed how breath training exercises enhance dance performance and improve a dancer’s control of their body, as well as how these exercises can function as material for choreographic inquiry. During the creation of the concert, the choreographer employed breath building exercises and applied different breath techniques with a cast of nine dancers. The choreographer and dancers worked collaboratively to develop creative material, enhance performance and help members of the audience understand why breathing in dance is so meaningful. / Dissertation/Thesis / Masters Thesis Dance 2019

No description available.

Power consumption and battery life are of critical importance for medical implant devices. For this reason, devices for Wireless Body Area Network (WBAN) applications must consume very little power. To save power, it is desirable to turn off or put to sleep a device when not in use. However, a transceiver, which is the most power hungry block of a wireless sensor node, needs to listen for the incoming signal continuously. An alternative scheme, is to listen for the incoming signal at a predetermined internal, which saves power at the cost of increased latency. Another and more sophisticated scheme is to provide a wake-up receiver, which listens for the incoming signal continuously, and upon detection of an incoming signal, it wakes the primary transceiver up. A wake-up receiver is typically simple and dissipates little power to make the scheme useful. This thesis proposes a low-power wake-up receiver, which listens for a wake-up signal, identifies the target node, and wakes up the primary receiver only when that specific node is called upon. When a wake up signal is transmitted to all of the nodes on a network, our wake-up receiver allows all the nodes on a network except the targeted node to remain asleep to save power. Several wake-up receiver topologies have been proposed. This work uses a passive Cockcroft-Walton multiplier circuit as an RF envelope detector followed by a simple detector circuit. A novel serial code detector is then used to decode the pulse width modulated input signal to wake-up the designated node. A passive RF front end and simple decoding circuit reduce power consumption substantially at the cost of low sensitivity. The sensitivity of the wake-up receiver can be improved though the addition of an RF amplifier, but at the cost of increased power consumption. / Master of Science

La consommation des systèmes de communication pour l'IoT peut être réduite grâce à un nouveau paradigme de réception radio. La technique consiste à ajouter un récepteur supplémentaire à chaque noeud IoT, appelé Wake Up Radio (WU-RX). Le rôle du WU-RX est de surveiller le canal de communication et de réveiller le récepteur principal (aussi appelé récepteur de données) lors de la réception d'une demande de communication. Une analyse des implémentations des WU-RX existants montre que les systèmes de l'état de l'art sont suffisamment sensibles par rapport aux récepteurs de données classiques mais manquent de robustesse face aux brouilleurs. Pour améliorer cette caractéristique nous proposons un étage de filtrage accordable `a fréquence intermédiaire qui nous permet de scanner toute la bande FI en cherchant le canal utilisé pour la demande de réveil. Ce filtre a été implémenté en utilisant les principes du traitement numérique de données à temps continu et consiste en un CAN suivi par un processeur numérique à temps continu. Le principe de fonctionnement du CAN est basé sur les modulateurs delta, avec une boucle de retour améliorée qui lui permet la quantification des signaux de fréquence plus élevé pour une consommation énergétique plus faible. Par conséquent, il a une plage de fonctionnement entre 10MHz et 50MHz ; pour un SNDR entre 32dB et 42dB et une consommation de 24uW. Cela se traduit par une figure de mérite entre 3fJ/conv-step et 10fJ/conv-step, une des meilleures pour la gamme de fréquences sélectionnée. Le processeur numérique est constitué d'un filtre IIR suivi par un filtre FIR. L'atténuation hors bande apportée par le filtre IIR permet de réduire le taux d'activité vu par le filtre FIR qui, par conséquent, consomme moins d'énergie. Nous avons montré, en simulation, une réduction de la puissance consommée par le filtre FIR d'un facteur entre 2 et 3. Au total, les deux filtres atteignent plus que 40dB de réjection hors bande, avec une bande passante de 2MHz qui peut être délacée sur toute la bande passante du CAN. Dans un pire cas, le système proposé (CAN et processeur numérique) consomme moins de 100uW, cependant la configuration des signaux à l'entrée peut rendre cette consommation plus faible. / Wake-Up Receivers (WU-RX) have been recently proposed as candidates to reduce the communication power budget of wireless networks. Their role is to sense the environment and wake up the main receivers which then handle the bulk data transfer. Existing WU-RXs achieve very high sensitivities for power consumptions below 50uW but severely degrade their performance in the presence of out-of-band blockers. We attempt to tackle this problem by implementing an ultra low power, tunable, intermediate frequency filtering stage. Its specifications are derived from standard WU-RX architectures; it is shown that classic filtering techniques are either not tunable enough or demand a power consumption beyond the total WU-RX budget of 100uW. We thus turn to the use of Continuous Time Digital Signal Processing (CT-DSP) which offers the same level of programmability as standard DSP solutions while providing an excellent scalability of the power consumption with respect to the characteristics of the input signal. A CT-DSP chain can be divided into two parts: the CT-ADC and the CT-DSP itself; the specifications of these two blocks, given the context of this work, are also discussed. The CT-ADC is based on a novel, delta modulator-based architecture which achieves a very low power consumption; its maximum operation frequency was extended by the implementation of a very fast feedback loop. Moreover, the CT nature of the ADC means that it does not do any sampling in time, hence no anti-aliasing filter is required. The proposed ADC requires only 24uW to quantize signals in the [10MHz 50MHz] bandwidth for an SNR between 32dB and 42dB, resulting in a figure of merit of 3-10fJ/conv-step, among the best reported for the selected frequency range. Finally, we present the architecture of the CT-DSP which is divided into two parts: a CT-IIR and a CT-FIR. The CT-IIR is implemented by placing a standard CT-FIR in a feedback loop around the CT-ADC. If designed correctly, the feedback loop can now cancel out certain frequencies from the CT-ADC input (corresponding to those of out-of-band interferers) while boosting the power of the useful signal. The effective amplitude of the CT-ADC input is thus reduced, making it generate a smaller number of tokens, thereby reducing the power consumption of the subsequent CT-FIR by a proportional amount. The CT-DSP consumes around 100uW while achieving more than 40dB of out-of-band rejection; for a bandpass implementation, a 2MHz passband can be shifted over the entire ADC bandwidth.

In ultra-low power Wireless Sensor Networks (WSNs) sensor nodes need to interact, depending on the application, even at a rapid pace while preserving battery life. Wireless communication brings thereby quite the burden as the radio transceiver requires a relative huge amount of power during both transmission or reception phases. In WSNs with on demand communication, the sensor nodes are required to maintain responsiveness and to act the sooner they receive a request, reducing the overall latency of the network. The aspect is more challenging in asynchronous WSN as the receiver possesses no information about the packet arrival time. In a purely on-demand communication, duty-cycling shows little to almost no improvement. The receiving node, in such scheme, is expected to last for years while also being accessible to other peers. Here arises the utility of an external ultra-low power radio receiver known as Wake-up Receiver (WuRx). Its essential task is to remain as the only part of the system running while the rest of the systems enters the lowest power mode (i.e., sleep state). Once a request signal is received, it notifies the host processor and other peripherals for an incoming communication. With the sensor node being in sleep state (WuRx active only), substantial power levels can be achieved. If the WuRx is able to interact rapidly, the added latency remains negligible. As crucial performance figures, the sensitivity and bit rate are immediately affected by the extreme low-power budget at diifferent magnitudes, depending mainly on the incorporated architecture. This thesis focuses on the design of a feature-balanced WuRx. The passive radio frequency architecture (PRF) relies on passive detection while consuming zero power to extract On-Off-Keying (OOK) modulated envelopes. The featured sensitivity, however, is reduced compared to more complex architectures. A WuRx based on PRF architecture can effectively enable short-range applications. The sensitivity can vary with respect to several parameters including the total generated noise, circuit technology and topology. Two variants of the PRF WuRxs are introduced with the baseband amplifier being the main change. The first revision employs a high performance amplifier with reduced average energy consumption, thanks to a novel power gating control. The second variant focuses on employing an ultra-low power baseband amplifier as it is expected to be in a continuous active state. This thesis also brings the necessary analysis on the passive front-end with the intention to enhance the overall WuRx sensitivity. Proof of concepts are embedded in sensor node boards and feature -61 dBm and -64 dBm of sensitivity for the first and the second variant, respectively, at a packet-error-rate (PER) of 1% whilst demanding a similar power of 7.2 µW during packet listening. During packet decoding, the first variant demands a 150 µW of power, caused greatly by the baseband amplifier. The achieved latency is less than 30 ms and the bit rate is 4 kbit/s, Manchester encoding. For long-range applications, a higher sensitivityWuRx is proposed based on Tuned-RF (TRF) architecture. By embedding a low-noise amplifier (LNA) in the receiver chain, very weak radio signal can be detected. TheWuRx emphasizes higher sensitivity of -90 dBm. The design of the LNA prioritized the highest gain and lowest bias current by sacrifcing the linearity that poses little impact on signal integrity for the OOK modulated signals. The total active power consumption of the TRF WuRx is 1.38 mW. In this work, a fast sampling approach based on power gating protocol allows a drastic reduction in energy consumption on average. By being able to sample in matter of few microseconds, the WuRx is able to detect the presence of a packet and return to sleep state right after packet decoding. Being power-gated dropped the average power consumption to 2.8 µW at a packet detection latency of 32 ms for less than 2 s of interval time between communication requests. The proposed solutions are able to decode a minimum length of 16-bit pattern and operate in the license-free ISM band 868 MHz. This thesis also includes the analysis and implementation of low-power front-end building blocks that are employed by the proposed WuRx.:1 Introduction 1.1 Motivation 1.2 Wake-up Receiver Design Requirements 1.2.1 Energy Consumption 1.2.2 Network Coverage and Robustness 1.2.3 Wake-up Packet Addressing 1.2.4 WuPt Detection Latency 1.2.5 Hosting System, Form-factor and Fabrication Technology 1.3 Thesis Organisation 2 Wireless Sensor Networks 2.1 Radio Communication 2.1.1 Electromagnetic Spectrum 2.1.2 Link Budget Analysis 2.2 Asynchronous Radio Receiver Duty-cycle Control 2.2.1 B-MAC and X-MAC Protocols 2.2.2 Energy and Latency Analysis 2.3 Power Supply Requirements 2.3.1 Low Self-discharge Battery 2.3.2 Energy Harvester 2.4 Summary 3 State-of-the-Art of Wake-up Receivers 3.1 Wake-up Receiver Architectural Analysis 3.1.1 Passive RF Detector 3.1.2 Classical Radio Architectures 3.2 Wake-up Receiver Back-end Stages 3.2.1 Baseband Amplifiers 3.2.2 Analog to Digital Conversion 3.2.3 Wake-up Packet Decoder 3.3 Power Consumption Reduction at Circuit Level 3.3.1 Power Gating 3.3.2 Interference Rejection and Filtering 3.4 Summary 4 Proposal of Novel Wake-up Receivers 4.1 Ultra-low Power On-demand Communication in Wireless Sensor Networks: Challenges and Requirements 4.2 Passive RF Wake-up Receiver 4.3 Power-gated Tuned-RF Wake-up Receiver 5 Low-power RF Front-end 5.1 Narrow-band Low-noise Amplifier (LNA) 5.1.1 Topology 5.1.2 Voltage Gain 5.1.3 Stability 5.1.4 Noise Figure 5.1.5 Linearity 5.2 Envelope Detector 5.2.1 Theory of Square-law Detection and Sensitivity Analysis 5.2.2 Single-Diode Envelope Detector 5.2.3 Voltage Multiplier Envelope Detector 5.3 Hardware Assessment 5.3.1 LNA 5.3.2 Envelope Detector 5.4 Summary 6 Passive RF Wake-up Receiver 6.1 Circuit Implementation 6.1.1 Address Decoder 6.1.2 Envelope Detector 6.1.3 Power-gated Baseband Amplifier 6.1.4 Ultra Low-power Baseband Amplifier 6.2 Experimental Results 6.2.1 Wireless Sensor Node 6.2.2 Measurements 6.3 Summary 7 Power-gated Tuned-RF Wake-up Receiver 7.1 Power-gating Protocol 7.2 Circuit Design 7.2.1 Radio Front-end 7.2.2 Data Slicer 7.2.3 Digital Baseband 7.3 Performance Evaluation 7.4 Summary 8 Conclusion 8.1 Performance Summary 8.2 Future Perspective 8.3 Applications A Two-tone Simulation Setup B Diode Models and Simulation Setup C Preamble Detection C Code Implementation Bibliography Publications / In drahtlosen Sensornetzwerken (WSNs) mit extrem geringem Stromverbrauch müssen Sensorknoten je nach Anwendung kurze Latenzzeiten erreichen ohne die Batterielebensdauer zu beeinträchtigen. Die drahtlose Kommunikation bringt dabei eine ziemliche Belastung mit sich, da der Funktransceiver sowohl während der Sende- als auch der Empfangsphase relativ viel Strom benötigt. Einige marktfähige Funktransceiver benötigen durchschnittlich ca. 10 mA im Empfangsmodus sowie 30 mA im Sendemodus. Deshalb wird heutzutage das sogenannte Duty-Cycling mit bestimmten Sende-, Empfangs- und langen Schlafzeitintervallen eingeführt. Während der Schlafphase ist der Empfänger nicht ansprechbar. Was wiederum zu einer massiven Erhöhung der Latenzzeit führen kann. In vielen Anwendungen und insbesondere im Rahmen der Digitalisierung von Prozessen wird mittlerweile die Fähigkeit On-Demand mit sehr kurzen Latenzzeiten zu kommunizieren verlangt. Diese Anforderung steht in einem Wiederspruch zum genannten Duty-cycle Betrieb. Um dieses Dilemma zu lösen wird im Rahmen dieser Doktorarbeit ein Funkempfänger mit extrem geringen Stromverbrauch untersucht und entwickelt. Mit Hilfe des extrem niedrigen Stromverbrauches kann der Funkempfänger ständig empfangsbereit sein. Er wird zum Hauptempfänger mit dem hohen Stromverbrauch zugeschaltet, so dass nur nach Aufforderung der Hauptempfänger aktiv sein wird. Dieser Empfänger wird Wake-up Empfänger (WuRx) genannt. Seine wesentliche Aufgabe besteht darin, als einziger Teil des Gesamtknotens aktiv zu sein, während der Rest in den Modus mit dem niedrigsten Stromverbrauch versetzt wird. Sobald ein Anforderungssignal empfangen wird, weckt er den Haupt-Prozessor und andere Peripheriegeräte über eine eingehende Kommunikation. Somit ist der Aufweckempfänger essenziell für die Zuverlässigkeit der drahtlosen Kommunikation. Sein Stromverbrauch sollte im µA Bereich sein. Seine Empfangsbereitschaft hängt entscheidend von seiner Empfindlichkeit sowie Bitrate ab. Eine Verbesserung der Empfindlichkeit und Erhöhung der Bitrate würden zwangsläufig zu einer Erhöhung des Stromverbrauches führen. Im Rahmen dieser Doktorarbeit werden unterschiedliche Architekturen von Aufweckempfängern untersucht und umgesetzt. Zusammenhänge zwischen Empfindlichkeit, Bitrate und Stromverbrauch wurden analysiert und mögliche Grenzen gezeigt. Ein wesentliches Augenmerk war dabei, Off-the-Shelf Komponenten zu verwenden. Im Rahmen dieser Doktorabeit wurden in Abhängigkeit von der zu erreichenden Reichweite und Häufigkeit der Kommunikation zwei wesentliche Architekturen mit geeigneten Empfindlichkeiten und extrem geringem Stromverbrauch entwickelt. Für kurze Reichweiten wurde eine passive Hochfrequenzarchitektur (PRF Architektur) basierend auf einer passiven Erkennung von OOK-modulierten (On-Off-Keying) Signalen mittels Hüllkurvenbildung entwickelt. Die erreichte Empfindlichkeit von ca. -64 dBm stellt eine wesentliche Verbesserung gegenüber dem Stand der Technik und Forschung mit einer Empfindlichkeit von ca. -52 dBm dar. Die Empfindlichkeit kann in Bezug auf verschiedene Parameter variieren, einschließlich des insgesamt erzeugten Rauschens, der Schaltungstechnologie und der Topologie. Zwei Varianten der PRF WuRxs wurden realisiert, wobei der Basisbandverstärker die Hauptänderung darstellt. Die erste Version verwendet einen Hochleistungsverstärker mit reduziertem durchschnittlichen Energieverbrauch dank einer neuartigen Leistungssteuerung. Die zweite Variante konzentriert sich auf die Verwendung eines Basisbandverstärkers mit extrem geringer Leistung, da erwartet wird, dass er sich in einem kontinuierlichen aktiven Zustand befindet. Diese Arbeit bringt auch die notwendige Analyse des passiven Front-Ends mit der Absicht, die allgemeine WuRx-Empfindlichkeit zu verbessern. Nachweise der Wirksamkeit sind in Sensorknotenmodulen eingebettet und verfügen über -61 dBm und -64 dBm Empfindlichkeit für die erste bzw. die zweite Variante bei einer Paketfehlerrate (PER) von 1 %, während beim Abhören von Paketen eine ähnliche Leistung von 7.2 µW gefordert wird. Während der Paketdecodierung erfordert die erste Variante eine Leistung von 150 µW, die stark durch den Basisbandverstärker verursacht wird. Die erreichte Latenz beträgt weniger als 30 ms und die Bitrate beträgt 4 kbit/s mit einer Manchester-Codierung. Für Anwendungen mit großer Reichweite wird ein WuRx mit höherer Empfindlichkeit vorgeschlagen. Dieser basiert auf einer TunedRF (TRF) -Architektur. Dabei werden sehr schwache Funksignale durch einen rauscharmen Verstärker (LNA) erkannt und verstärkt. Der WuRx erreicht eine bessere Empfindlichkeit von ca. –90 dBm. Dabei wurde das Augenmerk auf die höchste Verstärkung verbunden mit dem niedrigsten Vorspannungsstrom gelegt. Der LNA wird dann im nicht-linearen Bereich betrieben. Dieser Betriebsmodus beeinflusst nur im geringeren Maße die Signalintegrität der OOK-modulierten Signale. Der gesamte Leistungsverbrauch des TRF WuRx beträgt 1.38 mW. Um den Gesamtleistungsverbrauch im µW Bereich zu reduzieren, wird im Rahmen dieser Arbeit das sogenannte Power-Gating-Protokoll eingeführt. Dabei wird das Funkkanal zyklisch abgetastet. Der WuRx kann innerhalb von wenigen Mikrosekunden das Vorhandensein eines Pakets erkennen und direkt nach der Paketdecodierung in den Ruhezustand zurückkehren. Durch diesen Ansatz konnte der durchschnittliche Stromverbrauch bei einer Paketerkennungslatenz von ca. 32 ms innerhalb einer Abtastrate von 2 s auf 2.8 µW reduziert werden. Die vorgeschlagenen Lösungen können eine Mindestlänge von 16-Bit-Mustern decodieren und im lizenzfreien ISM-Band 868 MHz arbeiten.:1 Introduction 1.1 Motivation 1.2 Wake-up Receiver Design Requirements 1.2.1 Energy Consumption 1.2.2 Network Coverage and Robustness 1.2.3 Wake-up Packet Addressing 1.2.4 WuPt Detection Latency 1.2.5 Hosting System, Form-factor and Fabrication Technology 1.3 Thesis Organisation 2 Wireless Sensor Networks 2.1 Radio Communication 2.1.1 Electromagnetic Spectrum 2.1.2 Link Budget Analysis 2.2 Asynchronous Radio Receiver Duty-cycle Control 2.2.1 B-MAC and X-MAC Protocols 2.2.2 Energy and Latency Analysis 2.3 Power Supply Requirements 2.3.1 Low Self-discharge Battery 2.3.2 Energy Harvester 2.4 Summary 3 State-of-the-Art of Wake-up Receivers 3.1 Wake-up Receiver Architectural Analysis 3.1.1 Passive RF Detector 3.1.2 Classical Radio Architectures 3.2 Wake-up Receiver Back-end Stages 3.2.1 Baseband Amplifiers 3.2.2 Analog to Digital Conversion 3.2.3 Wake-up Packet Decoder 3.3 Power Consumption Reduction at Circuit Level 3.3.1 Power Gating 3.3.2 Interference Rejection and Filtering 3.4 Summary 4 Proposal of Novel Wake-up Receivers 4.1 Ultra-low Power On-demand Communication in Wireless Sensor Networks: Challenges and Requirements 4.2 Passive RF Wake-up Receiver 4.3 Power-gated Tuned-RF Wake-up Receiver 5 Low-power RF Front-end 5.1 Narrow-band Low-noise Amplifier (LNA) 5.1.1 Topology 5.1.2 Voltage Gain 5.1.3 Stability 5.1.4 Noise Figure 5.1.5 Linearity 5.2 Envelope Detector 5.2.1 Theory of Square-law Detection and Sensitivity Analysis 5.2.2 Single-Diode Envelope Detector 5.2.3 Voltage Multiplier Envelope Detector 5.3 Hardware Assessment 5.3.1 LNA 5.3.2 Envelope Detector 5.4 Summary 6 Passive RF Wake-up Receiver 6.1 Circuit Implementation 6.1.1 Address Decoder 6.1.2 Envelope Detector 6.1.3 Power-gated Baseband Amplifier 6.1.4 Ultra Low-power Baseband Amplifier 6.2 Experimental Results 6.2.1 Wireless Sensor Node 6.2.2 Measurements 6.3 Summary 7 Power-gated Tuned-RF Wake-up Receiver 7.1 Power-gating Protocol 7.2 Circuit Design 7.2.1 Radio Front-end 7.2.2 Data Slicer 7.2.3 Digital Baseband 7.3 Performance Evaluation 7.4 Summary 8 Conclusion 8.1 Performance Summary 8.2 Future Perspective 8.3 Applications A Two-tone Simulation Setup B Diode Models and Simulation Setup C Preamble Detection C Code Implementation Bibliography Publications

The neurological wake-up test, NWT, is a clinical monitoring tool that can be used to evaluate the level of consciousness in patients with traumatic brain injury (TBI) and subarachnoid haemorrhage (SAH) during neurocritical care (NCC). Since patients with severe TBI or SAH are often treated with mechanical ventilation and sedation, the NWT requires that the continuous sedation is interrupted. However, interruption of continuous sedation may induce a stress response and the use of the NWT in NCC is controversial. The effects of the NWT on intracranial pressure (ICP) and cerebral perfusion pressure (CPP) were evaluated in 21 patients with TBI or SAH. Compared to baseline when the patients were sedated with continuous propofol sedation, the NWT resulted in increased ICP and CPP (p<0.05). Next, the effects of the NWT on the stress hormones adrenocorticotrophic hormone (ACTH), cortisol, epinephrine and norepinephrine were evaluated in 24 patients. Compared to baseline, the NWT caused a mild stress response resulting in increased levels of all evaluated stress hormones (p<0.05). To compare the use of routine NCC monitoring tools, the choice of sedation and analgesia and the frequency of NWT in Scandinavian NCC units, a questionnaire was used. The results showed that all 16 Scandinavian NCC units routinely use ICP and CPP monitoring and propofol and midazolam were primary choices for patient sedation in an equal number of NCC units. In 2009, the NWT was not routinely used in eight NCC units whereas others used the test up to six times daily. Finally, intracerebral microdialysis (MD), brain tissue oxygenation (PbtiO2) and jugular bulb oxygenation (SjvO2) were used in 17 TBI patients to evaluate the effect of the NWT procedure on focal neurochemistry and cerebral oxygenation. The NWT did not negatively alter interstitial markers of energy metabolism or cerebral oxygenation. In conclusion, the NWT induced a mild stress response in patients with TBI or SAH that did not result in a detectable, significant secondary insult to the injured brain. These results suggest that the NWT may safely be used as a clinical monitoring tool in the NCC of severe TBI and SAH in a majority of patients.