Automotive companies are actively pursuing to increase the use of high-strength-lightweight alloys such as aluminum, magnesium, and advanced/ultra high-strength steels (A/UHSS) in body panel and structural part applications to achieve fuel efficiency while satisfying several environmental and safety concerns. A/UHSS sheet materials with higher strength and crashworthiness capabilities, in comparison to mild steel alloys, are considered as a near-term (i.e., ~5 years) choice of material for body and structural components due to their relatively low cost when compared with other lightweight materials such as aluminum and magnesium. However, A/UHSS materials present an increased level of die wear and springback in stamping operations when compared to the currently used mild steel alloys due to their higher surface hardness and high yield strength levels. In order to prevent the excessive wear effect in stamping dies, various countermeasures have been proposed such as alternative coatings, modified surface enhancements in addition to the use of newer die materials including cast, cold work tool, and powder metallurgical tool steels. In this study, a new die wear test method was developed and tested to provide a cost-effective solution for evaluating various combinations of newly developed die materials, coatings and surfaces accurately and rapidly. A new slider type of test system was developed to replicate the actual stamping conditions including the contact pressure state, sliding velocity level and continuous and fresh contact pairs (blank-die surfaces). Several alternative die materials in coated or uncoated conditions were tested against different AHSS sheet blanks under varying load, sliding velocity circumstances. Prior to and after wear tests, several measurements and tribological examinations were performed to obtain a quantified performance evaluation using commonly adapted wear models. Analyses showed that (1) the rapid wear method is feasible and results in reasonable wear assessments, (2) uncoated die materials are prone to expose severe form wear (galling, scoring, etc.) problems; (3) coated samples are unlikely to experience such excessive wear problems, as expected; (4) almost all of the the recently developed die materials (DC 53, Vancron 40, Vanadis 4) performed better when compared to conventional tool steel material AISI D2, and (5) in terms of coating type, die materials coated with thermal diffusion (TD) and chemical vapor deposition (CVD) coatings performed relatively better compared to other tested coating types; (6) It was seen that wear resistance correlated with substrate hardness.

There are two main goals of this thesis. Firstly, to improve and develop an existing hot weartester at Karlstad University so that it may test more samples of different sizes. Secondly, totest previously impossible samples and investigate their tribological properties and measurethe coefficient of friction with high reproducibility. The development work on the tribometer wasdone by a prestudy including; Investigating the hot wear tester, idea generation in CAD andcollecting information from the creator and prior users of it. After a few rounds of conceptgeneration and discussion with the supervisor and workshop staff, a new sample holder withdifferent sample adapters was created. Five tests of four different materials were conductedand their friction was measured. The new sample holder was able to solve the mainconcerns with the old design and showed great promise in producing reproducible results,better than any previous versions. The friction of the different TiAlN samples, at roomtemperature, seemed to indicate that there is a certain amount of Al% that maximizes frictionand that there is no simple linear relationship between Al% and coefficient of friction. Finallyit can be concluded that the initial goals of the thesis have been met, and that a newscientific instrument has been created to aid in the further understanding of tribology. / Det finns två huvudsakliga mål med detta examensarbete. För det första, att förbättra ochutveckla en existerande varmnötare på Karlstad Universitet så att den kan testa fler proverav olika storlekar. För det andra, att testa tidigare omöjliga prov och undersöka derastribologiska egenskaper och mäta friktionskoefficienten med hög reproducerbarhet.Utvecklingsarbetet av tribometern skedde via en förstudie som innehöll följande:Undersökning av varmnötaren, idégenerering i CAD och samling av information frånvarmnötarens skapare, samt tidigare användare. Efter några iterationer avkonceptgenerering och diskussioner med handledare och verkstadspersonal så skapadesen ny provhållare med flera olika adaptrar. Fem tester med fyra olika material utfördes ochderas friktion mättes. Den nya provhållaren löste de huvudsakliga problemen med dengamla designen och påvisade goda förhoppningar angående att producera tester med högreproducerbarhet. Markant bättre än tidigare versioner. Friktionsmätningarna från de olikaTiAlN-proverna, vid rumstemperatur, indikerade att det finns en viss mängd Al% sommaximerar friktionen och att det inte finns något linjärt samband mellan Al% ochfriktionskoefficient. Slutligen kan det konstateras att de initiala målen för examensarbetet harblivit uppnådda, och att ett nytt vetenskapligt instrument har blivit skapat för att hjälpa utökaförståelse inom tribologi.

This thesis work was conducted at Luleå University of Technology in collaboration with Sandvik Rock Tools. The aim of the work was to determine the influence of carbon content on the wear performance in carburized steel in the dry contact interface of threaded connections between drill rods. In order to investigate this, samples of drill rod steel were carburized to three different carbon concentrations and shot peened to replicate the production process of a drill rod. The samples were wear tested by utilizing a twin-disc wear tester with one disc rotating at 100 RPM and the other at 3000 RPM to mimic the operating conditions in the threaded connection between drill rods. The results was evaluated by wear rate, surface topography, hardness as well as optical analysis by light optical microscopy and scanning electron microscopy. The results show that an increased surface carbon content provide a decrease in wear rate and an increase in hardness in the surface layer that undergo microstructural changes due to the frictional heat and contact pressure during wear testing. The primary wear mechanisms were identified as plastic deformation, adhesive scratching and material removal through delamination.