Yes / This study presents a compact broadband wide-slot antenna with broadband left-hand circular polarization compatible with both LTE 42 and LTE 43 standards of 5G mid-band applications. The proposed antenna is fabricated on an FR4 dielectric substrate with overall dimensions of , where is the free space wavelength at the resonant frequency of the antenna. The antenna ground plane is etched to form a square radiating slot with a pair of rectangular ground stubs that are diagonally placed inside the slot. On the other side of the antenna, the feed line is loaded by horizontal and vertical stubs to improve the coupling between the feed line and the square slot. To generate a circular polarization, the feeding stubs cooperate with the pair of rectangular ground stubs to excite the radiating slot of the antenna at two different feeding points whose currents have approximately equal amplitude and 90o phase shift. The measured impedance bandwidth (BW) of the proposed wide-slot antenna is 16.2% (580 MHz along the band 3.3-3.88 GHz), while the observed axial ratio bandwidth (ARBW) is 12.2% (440 MHz in the 3.4-3.84 GHz band). The measured gain values are found to be larger than 2.5 dB along both standards of the 5G mid-band applications. / This work was supported in part by the U.K. Engineering and Physical Sciences Research Council (EPSRC) under Grant EP/E022936/1, and in part by the European Union’s Horizon 2020 Research and Innovation Programme under Grant H2020-MSCA-ITN-2016 SECRET-722424.

Yes / A compact dielectric resonator antenna for ultra-wideband vehicular communication applications is proposed. Two cylindrical dielectric resonators are asymmetrically located with respect to the center of an offset rectangular coupling aperture, through which they are fed. Optimizing the design parameters results in an impedance bandwidth of 21%, covering the range from 5.9 to 7.32 GHz in the lower-band and a 53% relative bandwidth from 8.72 to 15 GHz in the upper-band. The maximum achieved gain is 12 dBi. Design details of the proposed antenna and the results of both simulations and experiment are presented and discussed.

<p> Manufacturing processes such as cold-bending flat sheet to a small radius produces a rather complex residual stress state through the thickness of light gauge structural steel sections. When the load-application device is released the sheet exhibits a phenomenon called "spring-back".</p> <p> The purpose of this research was to develop an exact method of computing the residual stresses in a wide sheet of ideal plastic metal after spring back and subsequently to study their effect on the behaviour of cold-formed sections. An approximate analysis based on the assumption of elastic spring back is presented for comparison purposes. It is demonstrated that plastic flow occurs within a thin core of sheet below the neutral axis and that the spring back is not completely elastic beyond a certain curvature. Such behaviour is particularly significant in cases where the radius of bend is of the same order as the thickness. An exact analysis based on a more realistic approach is then performed considering the adjustments in the stress components due to the plastic core. Computer programs have been developed to calculate the residual stresses associated with any given radius of bend. It is found that the choice of one yield criterion rather than the other does not have any effect on the present analysis and the stress components for Von Mises' material are (2/√3) times the components for Tresca's material. Furthermore, the effect of lateral stretching on the behaviour of cold-formed sections is briefly viewed.</p> <p> The purpose of the experimental work in this thesis was to verify the validity of some of the assumptions made in the analysis.</p> <p> Conclusions are drawn and suggestions made for further research.</p> / Thesis / Master of Engineering (MEngr)

Ternary III-nitride alloys have enabled the design of various devices ranging from optoelectronics to power electronics due to their tunable band gap. BxGa1-xN is a wide band gap semiconductor with applications in detecting devices, power electronics and light-emitting diodes. The band gap can be modulated by changing the Boron concentration. It can be grown by metal-organic chemical vapor deposition as a mixed thin film of wurtzite and zincblende structures. In this work, we investigate the structural and electronic properties of BxGa1-xN (x<0.2) by first-principles calculations for both the wurtzite and zincblende phases. The formation energies of Si and Mg impurities and of a Ga vacancy are also calculated. We find that the wurtzite structure is favored over the zincblende structure. Furthermore, the Si and Mg impurities have relatively low formation energies in their neutral state, which indicates compatibility with BxGa1-xN, while a Ga vacancy has very high formation energy, hence being less likely to form spontaneously. Moreover, in the charged states, the formation energy of Mg is reasonably low for most values of the Fermi level, while the formation energy of Si depends linearly on the Fermi level, indicating challenges in achieving n-type conductivity. For a Ga vacancy in a triple acceptor state, the formation energy is reasonably low close to the conduction band, therefore, Ga vacancies interfere with n-type conductivity.

A 3D Finite Element Boundary Integral technique (FE-BI) using mixed-order tangential vector finite elements (TVFE?s) is presented. This technique is used to design two wide band antennas and an ultra wideband (UWB) antenna array. Tetrahedral elements are used for domain discretization because they offer higher flexibility when simulating complex structures. A set of hierarchical mixed-order TVFE?s up to and including order 2.5 is implemented. Hierarchical mixed-order TVFE?s accurately simulate regions with high and low field variations. They also guarantee tangential field continuity across element boundaries and suppress spurious modes. The efficacy of the technique has been tested on two different wide band antennas and an UWB array. The first antenna is designed for automotive applications and covers GPS, GSM, XM, and PCS bands (0.8?3.35 GHz). The second antenna is a double sided rounded bowtie antenna (DSRBA) for UWB communication (3.1-10.6 GHz). The third design is a DSRBA array. For validation purposes, the antennas are also simulated using a commercially available high frequency electromagnetic simulation software, HFSS. Results regarding antenna parameters such as return loss, radiation pattern, and gain are also given.

Early planting of indeterminate soybean varieties has increased yield potential in Mississippi. Narrow row patterns have effectively alleviated canopy closure problems and maximized light interception. Stresses related to inadequate drainage persist. Field experiments were conducted in 2006 and 2007 to evaluate productivity and profitability of bedding systems to minimize stresses related to poor drainage. Soybean planted on a conventional 100 cm bedding system provided a higher degree of growth and development and higher seed yields than flat plantings when border irrigated both years. Raised 100 cm-wide beds offered 23 to 45% greater net returns above input costs relative to flat plantings in 2006 and 2007 respectively. Under simulated flood irrigation, soybean planted on 200 cm-wide beds produced yields similar to conventional beds in 2006; however in 2007 200 cm-wide beds produced higher yields than flat planted plots but lower than 100 cm-wide beds.

No description available.

No description available.

No description available.

No description available.