Vibration energy harvesting has been widely investigated by academia and industry in the past decade with focus on developing distributed power sources. One of the prime goals of energy harvesters is to provide power to wireless sensors allowing for the placement of these sensors in the remote and inaccessible areas where battery is not an option. Electromechanical modeling approaches have been developed for enhancing the mechanical to electrical conversion efficiencies utilizing electromagnetic, piezoelectric, and magnetostrictive mechanisms. Models based upon the constitutive equations for these three conversion mechanisms, supported by extensive experimental results available in literature, suggest that power requirement through energy harvesters can be met only when the total volume is in the range of 1-100 cm3. There exists a critical volume of 0.5 cm³ at which above which the electromagnetic mechanism exhibits higher power density as compared to the other mechanisms. Therefore, in this thesis electromagnetic energy conversion was adopted to develop high power energy harvesters. We also present a novel vibration energy harvesting method which rivals the power density and bandwidth of the traditional methods. The overarching theme throughout the design process was selecting the structure and fabrication methodology that facilitates the transition of the technology. The experimental models were characterized at accelerations and frequencies typically found in the environmental vibration sources. The thesis provides in-depth the design, modeling, and characterization of a vibration energy harvester which creates relative motion differently than the conventional harvesters. Conventional designs rely on amplifying the original source displacement operating at the resonance condition. In the harvester design proposed in this thesis, the relative motion is created by cancelling the vibration at one location and transferring the source vibration directly to another location by combining a vibration isolator with a vibration absorber. In this novel configuration, termed as Direct Vibration Harvester (DVH), the energy is harvested directly from the vibrating source mass rather than a vibrating seismic mass attached to the source increasing the harvesting bandwidth and power density. Four bar magnet and magnetic levitation architectures were modified and modeled to reach closer to the theoretical maximum power densities. Extensive FEM was utilized to understand the performance limitations of the existing structures and the results from this analysis paved the pathway towards the development of the DVH. �A comparative analysis of the performance of the DVH with the traditional harvesting methods in terms of normalized power output and bandwidth was conducted. Performance improvements of DVH required development of the high efficiency rotational generators as linear to rotational conversion occurs in the DVH. The optimized rotational generator was modeled and all the predicted performance metrics were validated through experiments. The generator was applied towards the fabrication of DVH and also in a micro windmill. The power density of the micro windmill was found to be better than all the other results reported in literature. Extensive fluid and structural modeling was conducted to tailor the performance of the micro windmill in the desired wind speed range. Combined, this thesis provides significant advancement on many fronts. It pushes the magnetic levitation and four-bar mechanism harvester systems to their theoretical limits. It demonstrates a novel direct vibration harvester that has the possibility of surpassing the power density and bandwidth of all the known vibration harvester with large magnitude of output power. It provides a design process for an efficient small scale electromagnetic generator that can form for the backbone of many rotational and linear harvesters. This generator was used to develop the world's highest power density micro windmill in the small wind speed range. / Ph. D.

Indiana University-Purdue University Indianapolis (IUPUI) / The harvested energy of wind can be transferred to the generators either through a gearbox or through an intermediate medium such as hydraulic fluids. In this method, high-pressure hydraulic fluids are utilized to collect the energy of single or multiple wind turbines and transfer it to a central generation unit. In this unit, the mechanical energy of the hydraulic fluid is transformed into electric energy. The prime mover of hydraulic energy transfer unit, the wind turbine, experiences the intermittent characteristics of wind. This energy variation imposes fluctuations on generator outputs and drifts their angular velocity from desired frequencies. Nonlinearities exist in hydraulic wind power transfer and are originated from discrete elements such as check valves, proportional and directional valves, and leakage factors of hydraulic pumps and motors. A thorough understanding of hydraulic wind energy transfer system requires mathematical expression of the system. This can also be used to analyze, design, and predict the behavior of large-scale hydraulic-interconnected wind power plants. This thesis introduces the mathematical modeling and controls of the hydraulic wind energy transfer system. The obtained models of hydraulic energy transfer system are experimentally validated with the results from a prototype. This research is classified into three categories. 1) A complete mathematical model of the hydraulic energy transfer system is illustrated in both ordinary differential equations and state-space representation. 2) An experimental prototype of the energy transfer system is built and used to study the behavior of the system in different operating configurations, and 3) Controllers are designed to address the problems associated with the wind speed fluctuation and reference angular velocity tracking. The mathematical models of hydraulic energy transfer system are also validated with the simulation results from a SimHydraulics Toolbox of MATLAB/Simulink®. The models are also compared with the experimental data from the system prototype. The models provided in this thesis do consider the improved assessment of the hydraulic system operation and efficiency analysis for industrial level wind power application.