1 |
Studies on the performance structure and relevant parameters determining individual performance in the Paralympic port Alpine Skiing - Case StudyCampos Vinagre, Nelson Alexandre 29 May 2013 (has links)
No description available.
|
2 |
Development of a Wind Turbine Test Rig and Rotor for Trailing Edge Flap InvestigationAbdelrahman, Ahmed 13 September 2014 (has links)
Alleviating loads on a wind turbine blades would allow a reduction in weight, and potentially increase the size and lifespan of rotors. Trailing edge flaps are one technology proposed for changing the aerodynamic characteristics of a blade in order to limit the transformation of freestream wind fluctuations into load fluctuations within the blade structure. An instrumented wind turbine test rig and rotor were developed to enable a wide-range of experimental set-ups for such investigations. The capability of the developed system was demonstrated through a study of the effect of stationary trailing edge flaps on blade load and performance. The investigation focused on measuring the changes in flapwise bending moment and power production for various trailing edge flap parameters. The blade was designed to allow accurate instrumentation and customizable settings, with a design point within the range of wind velocities in a large open jet test facility. The wind facility was an open circuit wind tunnel with a maximum velocity of 11m/s in the test area. The load changes within the blade structure for different wind speeds were measured using strain gauges as a function of flap length, location and deflection angle. The blade was based on the S833 airfoil and is 1.7 meters long, had a constant 178mm chord and a 6o pitch. The aerodynamic parts were 3D printed using plastic PC-ABS material. The total loading on the blade showed higher reduction when the flap was placed further away from the hub and when the flap angle (pitching towards suction side) was higher. The relationship between the load reduction and deflection angle was roughly linear as expected from theory. The effect on moment was greater than power production with a reduction in moment up to 30% for the maximum deflection angle compared to 6.5% reduction in power for the same angle. Overall, the experimental setup proved to be effective in measuring small changes in flapwise bending moment within the wind turbine blade.
|
3 |
Wind shielding analysis for cold regions using experimental and numerical techniquesXu, Yizhong January 2016 (has links)
The thesis presents a systematic experimental and numerical study on the interactions among porous fence, airflow, and windblown snowdrifts, a knowledge that will contribute to optimize the performance of porous wind shielding system in Cold Regions. A comprehensive review of the concepts, theories, techniques, and key findings associated with the research work has been undertaken. The key technical parameters influencing fence performance have been systematically studied by means of wind tunnel experimental investigations and Computational Fluid Dynamics (CFD) simulations. The study has found that porosity is the most influential structural parameter affecting the performance of porous fences in many aspects. Fence height stands a significant positive position in terms of its performance. It was found that fence performance is not sensitive to the changes of approaching atmospheric airflow velocity. Nevertheless, a bottom gap can improve snow fence trap efficiency. All of those findings agree with most of the findings of other researchers, which affirms that the research methodology adopted in this research is sound. Physical experimental work was performed to assess the reliability and credibility of the numerical models. Those models have been intentionally simplified, which made them easier to construct and quicker to obtain numerical solutions at a lower computational cost. Furthermore, the numerical models demonstrate the level of competence acquired through this research that is implemented in the optimisation of fence design. Special attention has been paid to the issues where elaborate research work has not been systematically reached in the open literature, this includes areas such as the effects of arrangement of porous holes, fence surface shear, and directions of wind load with respect to the fence, etc. Correlation between the reattachment length, the shelter distance, and the creation and distribution of fence surface shear is reported, to the author's knowledge, for the first time in the open literature. General guidelines for the design of shelters based on porous fences have been established through this study. For example, the desirable size of hole range should be identified beforehand, and porous holes with sharp angular corners should usually be avoided in the fence design. It is recommended to place the fence within an angle of 30° to the wind load, where the effective shelter distance can be estimated in a linearized equation, and the normal drag coefficient can be described as a function of cos2θ. Optimal design of the arrangement of porous holes will maximize the fence performance, especially when the close fence environment is of concern. Although the definition of fence effective zone is still vague in the research field, the key factors influencing the fence effective zone have been investigated by evaluating the reduction of wind velocity leeward of the fence in this thesis. It is found that the fence effective zone is not sensitive to the change of approaching airflow velocity, and that increasing fence height will increase the physical size of the fence effective zone, but not in a proportional manner. It is also concluded that fence effective zone will be significantly reduced when the non-normal wind load is inclined at an angle greater than 30° to the fence. The effective zone increases effectively when the fence porosity is optimal. In contrast to the majority of published research work, the transient snow transport model presented in this work considers the snow transport rate as a whole without distinguishing the rate in saltation and suspension layer. The numerical study indicated that the position of the snow crest is mainly determined by the fence height, while porosity and bottom gap mainly affect the downwind deposition length. The optimal porosity for snow fences is in the range of 0.4 to 0.5, which is greater than the one for wind fences, which lies in the range from 0.25 to 0.35. Two snow crests have been observed leeward the fence at the onset of snow deposition, when the fence was placed without a bottom gap to the snow ground. This finding has not been encountered in any of the reported research work. Wind tunnel simulations of snowdrift around the fences have marginally under-predicted the sizes of snow deposition. The numerical predictions were quantitatively and qualitatively in good agreement with the field observations. This incompetence of wind tunnel experiments on porous fences implies that numerical modelling can play a more important role in snow fence research.
|
4 |
Cable Shape Optimization - Drag Reduction of Cables Used in Marine ApplicationsGarpenquist, Simon January 2023 (has links)
It is important to understand the aerodynamic properties of tensioned cables (e.g. used in suspension bridges and yacht riggings), both for drag reduction and vibrational suppression purposes. In this study, the cross-sectional shape and surface structure of solid cables were investigated in order to improve the performance of sailing racing yachts. The apparent wind angle range 15-60° was identified as the most important for drag reduction. Thereafter, the aerodynamic properties of different shapes and surfaces were investigated in the Reynolds number range 5 x 10^3 ≤ Re ≤ 4 x 10^4, by performing computational fluid dynamics simulations and wind tunnel tests (the aerodynamic forces were measured using load cells). No significant effect of changing the surface roughness could be found for the investigated Reynolds number range. The results were compared to literature values for validation. Elliptical shapes with a fineness ratio between 1:1-3:1, together with three complex shapes, were tested. It could be shown that the largest performance gain was obtained for cables with more sail-like aerodynamic properties (for apparent wind angles below 90° a large lift/drag ratio is sought). This study was performed in collaboration with Carbo-Link AG, as an outlook, the manufacturability of carbon fiber reinforced polymer cables in the most aerodynamically efficient shape was explored.
|
Page generated in 0.0946 seconds