No description available.

This investigation was initiated by IBM to determine the types of cracks formed in hot-isostatic-pressed (HIP) Ni-Zn ferrite under impact and static loading conditions. A 1/8-inch tungsten carbide (WC) ball was used to apply the load in both cases. The impact loading condition was accomplished by dropping the WC ball from various heights between 40 and 200 cm. The static loading condition was accomplished by applying loads of 10 kg, 15 kg, and 30 kg on a Rockwell Hardness Tester. The response of HIP Ni-Zn ferrite to impact and static loading was elastic/plastic yielding permanent indentations. "Dimple" impressions, Hertzian-ring cracks, and radial cracks were formed upon applying increasing loads to the HIP Ni-Zn ferrite. As the grain size of the material was increased, both the Hertzian-ring and radial cracks were formed at lower loads compared to the as-received samples. The "dimple" impressions were not observed to follow this trend.

No description available.

Magnesium sheet for automotive applications is very attractive due to its light weight. The poor formability of magnesium and its alloys at room temperature, however, has limited the applications of these alloys. For this reason, at present, magnesium must be formed at elevated temperatures. This study investigates the hot deformation and fracture characteristics of Mg-1wt% Zn alloys containing a range of Al and Mn levels. Hot-rolled specimens were tensile tested over a range of strain rates and temperatures. Strain rate versus flow stress diagrams plotted on log-log scales revealed a transition in deformation mechanisms as a change in slope (the 'stress exponent'). Specifically, non-uniform deformation (i.e. necking) is observed at high strain rates, while uniform deformation is observed at low rates. This transition is accompanied by a change in fracture mechanism from dimpled rupture at high strain rates to cavitation and cavity interlinkage at low strain rates. Specimens which had a stress exponent of ∼2 and which failed through uniform deformation showing interlinked cavities have been associated with the grain boundary sliding (GBS) deformation mechanism. Specimens which had a stress exponent of ~5 and which failed through necking showing a dimpled fracture surface have been associated with the dislocation creep deformation mechanism. Increasing aluminum appears to somewhat favour the GBS regime as indicated by a slightly decreasing stress exponent. Manganese also appears to favor the GBS regime, since the onset of cavitation appears at higher strain rates compared to alloys without Mn.

Thesis (M.S.)--University of North Texas, Dec., 2009. / Title from title page display. Includes bibliographical references.

Thesis (M.S. in material science and engineering)--Washington State University, May 2010. / Title from PDF title page (viewed on July 14, 2010). "School of Mechanical and Material Engineering." Includes bibliographical references (p. 90-92).

Thesis (Ph. D.)--University of Wisconsin--Madison, 1984. / Typescript. Vita. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references (leaves 194-209).

Thesis (M.Sc.)--City University of Hong Kong, 2005. / At head of title: City University of Hong Kong, Department of Physics and Materials Science, Master of Science in materials engineering & nanotechnology dissertation. On t.p. the "x" of "CdxZn₁-xS" are subscript. Title from title screen (viewed on Sept. 4, 2006) Includes bibliographical references.

Orientador: Amauri Garcia / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica / Made available in DSpace on 2018-08-23T08:57:42Z (GMT). No. of bitstreams: 1 DiasFilho_JoseMarcelinodaSilva_M.pdf: 6517871 bytes, checksum: ef7c786d7139cf30a13befba0cfaf24d (MD5) Previous issue date: 2013 / Resumo: O resumo poderá ser visualizado no texto completo da tese digital / Abstract: The abstract is available with the full electronic document / Mestrado / Materiais e Processos de Fabricação / Mestre em Engenharia Mecânica

No description available.