The hybridization of direct write (DW) and additive manufacturing (AM) technologies to create additively manufactured electronics (AME) has enabled the integration of electrical functionality to form multifunctional AM components. Current work in AME has demonstrated the integration of conductive traces into and onto geometries and form factors that are not possible through traditional electronics packaging processes. This has largely been accomplished by using AM and DW technology to deposit conductive inks to form interconnects on the surface of AM substrates or within multimaterial AM geometries. However, the requisite thermal post-processing and high resistivity of the conductive inks and the limitations in thermal and dielectric performance of printable substrates commonly used in AME restrict the capabilities of these parts.
This thesis proposes an alternative process for the conformal deposition of low resistivity traces on additively manufactured all-aromatic polyimides (AM-PI) without the use of conductive inks. This is accomplished through the selective patterning of laser induced graphene (LIG), a porous 3D graphene fabricated via laser irradiation, onto the AM-PI. While the resultant LIG is conductive, its resistivity is further reduced by the electrodeposition of copper (Cu-LIG).
In this thesis, the synthesis of LIG on AM-PI, thermally post processed to 240℃, 300℃, and 450℃, is demonstrated and characterized through sheet resistance measurements and Raman spectroscopy. AM-PI post-processed to 300℃ demonstrated the lowest resistivity LIG formation (13.8 Ω/square). The resistivity of Cu-LIG is compared to an industry standard silver ink (Micromax CB028) used in direct write hybrid manufacturing applications. Cu-LIG was found to have a measured resistivity (1.39e-7 Ω·m), two orders of magnitude lower than the measured resistivity of the CB028 silver ink (1.62e-5 Ω·m). Additionally, the current capacity of the Cu-LIG was demonstrated and Joule heating of the material was observed via IR thermography. Cu-LIG demonstrated no failure of conductive trace or substrate under 5A of current for 2 minutes, heating to a maximum recorded temperature of 76.3℃.
Several multifunctional components were fabricated as case studies to further validate the process. Several small passive electronic devices (e.g., a heater and an interdigitated capacitor) are fabricated to demonstrate selective deposition of complex copper traces. The fabrication of an Archimedes spiral on a hemispherical substrate via Cu-LIG is completed to demonstrate the ability to use the process to fabricate conformal conductive traces. An LED circuit is fabricated on a face-center cubic AM-PI lattice which demonstrates multi-planar fabrication on geometrically complex 3D printed substrates. / Master of Science / The hybridization of direct write (DW) and additive manufacturing (AM) technologies to create additively manufactured electronics (AME) has enabled the fabrication of AM components which have electronic functionality. Current work in AME has demonstrated the integration of conductive traces into and onto geometries and form factors that are not possible through traditional electronics packaging processes. This has largely been accomplished through the deposition of conductive inks to form interconnects on the surface of AM substrates or within multimaterial AM geometries. However, these conductive inks require thermal post-processing temperatures which exceed the thermal performance of common AM substrates. The dielectric performance of AM substrates is also restrictive to the capabilities of these parts.
This thesis proposes an alternative process for the conformal deposition of low resistivity traces on high performance additively manufactured all-aromatic polyimides (AM-PI) without the use of conductive inks. This is accomplished through the selective patterning of laser induced graphene (LIG), a porous 3D graphene fabricated via laser irradiation, onto the AM-PI. While the resultant LIG is conductive, its resistivity is further reduced by the electrodeposition of copper (Cu-LIG).
In this thesis, the synthesis of LIG on AM-PI, thermally post processed to 240℃, 300℃, and 450℃, is demonstrated and characterized through sheet resistance measurements and Raman spectroscopy. AM-PI post-processed to 300℃ demonstrated the lowest sheet resistance LIG formation (13.8 Ω/square). The resistivity of Cu-LIG is compared to an industry standard silver ink (Micromax CB028) used in direct write hybrid manufacturing applications. Cu-LIG was found to have a measured resistivity (1.39e-7 Ω·m), two orders of magnitude lower than the measured resistivity of the CB028 silver ink (1.62e-5 Ω·m). Additionally, the thermal performance and current capacity of the Cu-LIG was demonstrated by observing resistive heating of the material under current load via IR thermography. Cu-LIG demonstrated no failure of conductive trace or substrate under 5A of current for 2 minutes, heating to a maximum recorded temperature of 76.3℃.
Several multifunctional components were fabricated as case studies to further validate the process. A heater and an interdigitated capacitor are fabricated to demonstrate selective deposition of complex copper traces. The fabrication of an Archimedes spiral on a dome via Cu-LIG is completed to demonstrate the ability to use the process to fabricate conformal conductive traces. An LED circuit is fabricated on an AM-PI lattice which demonstrates multi-planar fabrication on geometrically complex 3D printed substrates.
| Identifer | oai:union.ndltd.org:VTETD/oai:vtechworks.lib.vt.edu:10919/118627 |
| Date | 03 April 2024 |
| Creators | Wotton, Heather Dawn |
| Contributors | Mechanical Engineering, Williams, Christopher Bryant, Bartlett, Michael David, Davis, Bradley A. |
| Publisher | Virginia Tech |
| Source Sets | Virginia Tech Theses and Dissertation |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Format | ETD, application/pdf |
| Rights | In Copyright, http://rightsstatements.org/vocab/InC/1.0/ |
Page generated in 0.0022 seconds