Selective laser melting (SLM) is a powder-based additive manufacturing technique consisting of the exact reproduction of a three dimensional computer model (generally a computer-aided design CAD file or a computer tomography CT scan) through an additive layer-by-layer strategy. Because of the high degree of freedom offered by the additive manufacturing, parts having almost any possible geometry can be produced by SLM. More specifically, with this process it is possible to build parts with extremely complex shapes and geometries that would otherwise be difficult or impossible to produce using conventional subtractive manufacturing processes. Another major advantage of SLM compared to conventional techniques is the fast cooling rate during the process. This permits the production of bulk materials with very fine microstructures and improved mechanical properties or even bulk metallic glasses. In addition, this technology gives the opportunity to produce ready-to-use parts with minimized need for post-processing (only surface polishing might be required). Recently, significant research activity has been focused on SLM processing of different metallic materials, including steels, Ti-, Ni- and Al-based alloys. However, most of the research is devoted to the parameters optimization or to feasibility studies on the production of complex structures with no detailed investigations of the structure-property correlation.
Accordingly, this thesis focuses on the production and structure-property correlation of Al-12Si samples produced by SLM from gas atomized powders. The microstructure of the as-prepared SLM samples consists of supersaturated primary Al with an extremely fine cellular structure along with the residual free Si situated at the cellular boundaries. This microstructure leads to a remarkable mechanical behavior: the yield and tensile strengths of the SLM samples are respectively four and two times higher than their cast counterparts. However, the ductility is significantly reduced compared with the cast samples. The effect of annealing at different temperatures on the microstructure and resulting mechanical properties of the SLM parts has been systematically studied by analyzing the size, morphology and distribution of the phases. In addition, the mechanical properties of the SLM samples have been modeled using micro- structural features, such as the crystallite and matrix ligament sizes. The results demonstrate that the mechanical behavior of the Al-12Si SLM samples can be tuned within a wide range of strength and ductility through the use of the proper annealing treatment.
The Al-Si alloys are generally used as pistons or cylinder liners in automotive applications. This requires good wear resistance and sufficient strength at the operating temperature, which ranges between 373 – 473 K. Accordingly, the tensile properties of the SLM samples were also tested at these temperatures. Changing the hatch style during SLM processing vary the texture in the material. Hence, samples with different hatch styles were produced and the effect of texture on their mechanical behavior was evaluated. The results show that the hatch style strongly influences both the mechanical properties and the texture of the samples; however no direct correlation was observed between texture and mechanical properties. The wear properties of the Al-12Si material was evaluated using pin-on-disc and fretting wear experiments. These experiments show that the as-prepared SLM samples exhibit better wear resistance than their cast counterparts and the SLM heat-treated samples. Finally, the corrosion investigations reveal that the SLM samples have similar corrosion behavior as the cast specimens under acidic conditions.
A major drawback for the wide application of SLM as an industrial processing route is the limited size of the products. This is a direct consequence of the limited dimensions of the available building chambers, which allow for the production of samples with volumes of about 0.02 m3. A possible way to overcome this problem would be the use of the welding processes to join the small SLM objects to form parts with no dimensional limitations. In order to verify this possibility, friction welding was employed to join Al-12Si SLM parts. The results indicate that friction welding not only successfully permits the join materials manufactured by SLM, but also helps to significantly improve their ductility.
This work clearly demonstrates that SLM can be successfully used for the production of Al-12Si parts with an overall superior performance of the mechanical and physical properties with respect to the conventional cast samples. Moreover, the mechanical properties of the SLM samples can be widely tuned in-situ by employing suitable hatch styles or ex-situ by the proper heat treatment. This might help the development of SLM for the production of innovative high-performance Al-based materials and structures with controlled properties for automotive and aerospace applications.
| Identifer | oai:union.ndltd.org:DRESDEN/oai:qucosa.de:bsz:14-qucosa-144245 |
| Date | 17 July 2014 |
| Creators | Prashanth, Konda Gokuldoss |
| Contributors | Technische Universität Dresden, Fakultät Maschinenwesen, Prof. Dr.Ing- habil. Jürgen Eckert, Prof. Dr. Nilay K. Mukhopadhyay |
| Publisher | Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden |
| Source Sets | Hochschulschriftenserver (HSSS) der SLUB Dresden |
| Language | English |
| Detected Language | English |
| Type | doc-type:doctoralThesis |
| Format | application/pdf |
Page generated in 0.0029 seconds