<p>This dissertation focused on cured-in-place-pipe (CIPP) technology, which is being used to repair sewer pipes across the globe. The CIPP process involves the manufacture of a new fiber-reinforced composite plastic pipe inside an existing damaged pipe. By 2022, the global CIPP market will exceed $2.5 billion and constitute 40% of the U.S. pipe rehabilitation market. In recent years, concerns about the type, magnitude, and toxicity of chemical air emissions associated with CIPP installations have markedly increased. CIPP installations in Asia, Europe, Oceania, and North America have been associated with indoor and ambient air contamination incidents, afflicted schools, daycare centers, homes, and offices and prompted building evacuations. This research program was designed to better understand chemical release into the air during CIPP composite manufacture and the human health risks. Principles and techniques from the environmental engineering, air quality, material science, and risk analysis were applied. This dissertation contains three chapters and each chapter is a stand-alone manuscript, with the first chapter already having been published.</p><p>Chapter 1 involved the characterization of chemical emissions for steam-cured CIPP installations in Indiana (IN, sanitary sewer) and California (CA, storm sewer). It was discovered that a complex multiphase mixture of organic vapor, water vapor, and particulate (condensable vapor and partially cured resin) was emitted. Chemicals captured included a variety of hazardous air pollutants, carcinogens, endocrine disrupting compounds, and other chemicals with little toxicity data. The materials captured in California during 4 CIPP installations, when normalized against styrene concentration, exhibited different toxicity towards mouse cells. This toxicity indicated that non-styrene compounds were probably responsible for toxicity. Testing revealed significant and previously unreported worker and public safety chemical risks existed with CIPP installations.</p><p>Chapter 2 describes experiments conducted to determine which CIPP manufacturing conditions (i.e. curing pressure, temperature, time and ventilation) influenced chemical air emissions during and after composite manufacture. During thermal manufacture, approximately 8.87 wt% volatile organic compounds (VOC) was released into the air at standard pressure. For the CIPP styrene-based resin examined, chemical volatilization during manufacture was influenced by pressure, but temperature and heating time did not influence the composition of chemical residual inside the new composite. All cured composites, regardless of temperature or heating time, contained approximately 3 wt% VOC. No statistical difference was found for either: (1) VOC loading across cured composites or (2) styrene emission into the air across cured composites despite different curing temperature and heating times. Styrene was the most abundant compound detected in the composite and in air. High styrene air concentration signals inhibited the author’s ability to determine if other non-styrene compounds were emitted into the air. Short-term ventilation (2 hr) of the new composite reduced styrene air concentration to near zero in 10 min, but styrene levels rebounded when ventilation was halted. Due to the high styrene loading in the cured composite, it is expected that ventilation will only temporarily reduce VOC air levels in pipes, manholes, and other affected spaces.</p><p>Chapter 3 includes inhalation health risk assessment due to chemical emission from CIPPs during manufacture and use. Publicly available worksite data for ultraviolet (UV)-light and steam-CIPP installations were utilized and Monte Carlo simulation was applied. Data-gaps were also identified. Health risks associated with newly manufactured (post-cured) chemical emission from lab scale CIPPs were also evaluated. For CIPP resins and post-cured CIPPs 31 chemicals have been quantified among which many are unique volatile organic chemicals VOCs, but only 8 air testing studies were found. At a steam-CIPP worksite, VOCs were found in a condensed multiphase mixture discharged into air, 4 VOCs were detected in the vapor phase, while only styrene vapor phase results could be used for risk assessment. Worksite styrene levels (1,825 ppm<sub>v</sub>, 1,070 ppm<sub>v</sub>, 220-270 ppm<sub>v</sub>, 140 ppm<sub>v</sub>) have been reported indicating a health risk can exist. Monte Carlo simulation using literature data revealed that for the single UV-CIPP and single steam-CIPP study negligible styrene HQs were found, while unacceptable styrene LECRs% > 10<sup>−4</sup> (i.e. 37-38%) were obtained. Monte Carlo simulation on laboratory data showed that post-cured emissions from the composite cured longer increased the unacceptable styrene LECR (from 17.86% to 21.12%) and HQ (0.95% to 8.04%). Whereas curing the composite at greater temperature reduced the styrene LECR and HQ to 0.89%. and 0, respectively. Ventilation also diminished the acceptable LECR% in all composites but did not reduce the carcinogenic health risk to an acceptable level. Health risk can exist as evidenced by limited air testing data. More studies are needed to examine inhalation health risks associated with the CIPP manufacturing process and newly manufactured plastics.</p>
| Identifer | oai:union.ndltd.org:purdue.edu/oai:figshare.com:article/12185259 |
| Date | 21 June 2022 |
| Creators | Seyedeh-Mahboobeh Teimouri-Sendesi (8755941) |
| Source Sets | Purdue University |
| Detected Language | English |
| Type | Text, Thesis |
| Rights | CC BY 4.0 |
| Relation | https://figshare.com/articles/thesis/IMPROVING_WORKER_SAFETY_AND_ENVIRONMENTAL_PROTECTION_BY_UNDERSTANDING_CHEMICAL_EMISSIONS_FROM_PLASTIC_COMPOSITES_DURING_MANUFACTURE_AND_USE/12185259 |
Page generated in 0.0022 seconds