Due to the high electron mobility compared with Si, much attention has been focused on III-V compound semiconductors (gallium arsenide (GaAs) and indium phosphide (InP)) high-speed devices. The high-k material TiO2 not only has high dielectric constant (k = 35-100) but has well lattice match with GaAs and InP substrate. Therefore, titanium oxide (TiO2) was chosen to be the gate oxide in this study.
The major problem of III-V compound semiconductors is known to have poor native oxide on it and leading to the Fermi level pinning at the interface of oxide and semiconductor. The C-V stretch-out phenomenon can be observed and the leakage current is high. The higher dielectric constant of poly-crystalline TiO2 film grown on GaAs can be obtained by metal organic chemical vapor deposition (MOCVD). But the high leakage current also occurred due to the grain boundary and defects in the poly-crystalline TiO2 film.
The surface passivation of GaAs with (NH4)2Sx treatment (S-GaAs) could prevent it from oxidizing after cleaning and improve the interface properties of MOSFET. The fluorine from liquid phase deposited SiO2 solution can passivate the grain boundary of poly-crystalline MOCVD-TiO2 film and interface state. The high dielectric constant and low leakage current of fluorine passivated MOCVD-TiO2/S-GaAs can be obtained. The leakage current densities are 3.41 x 10-7 A/cm2 and 1.13 x 10-6A/cm2 at ¡Ó1.5 MV/cm, respectively. The Dit is 4.6 x 1011 cm-2eV-1 at the midgap. The dielectric constant can reach 71.
In addition, the post-metallization annealing (PMA) is another efficiency way to improve the MOCVD-TiO2 quality. The mechanism of PMA process is from the reaction between the aluminum contact and hydroxyl groups existed on TiO2 film surface. Then the active hydrogen is produced to diffuse through the oxide and passivate the oxide traps. For PMA (350oC)-MOCVD-TiO2 on S-GaAs MOS structure, the leakage current densities can reach 2.5 x 10-7 and 5 x 10-7 A/cm2 at ¡Ó1.5 MV/cm, respectively. The dielectric constant and the Dit are 66 and 5.96 x 1011 cm-2eV-1, respectively.
In order to avoid the leakage current from grain boundary of poly-crystalline TiO2, and liquid phase deposited TiO2 (LPD-TiO2) at low temperature can preserve the function of sulfur passivation. Therefore, the amorphous LPD-TiO2 was deposited on S-GaAs. The leakage current densities are 1.04 x 10-7 and 1.91 x 10-7 A/cm2 at ¡Ó0.5 MV/cm, respectively. The Dit is 3.2 x 1011 cm-2eV-1 and the dielectric constant is 48. The LPD-TiO2 film was deposited on (NH4)2Sx treated InP (S-InP), and the 4 x 100 £gm2 enhancement mode N channel InP MOSFET with LPD-TiO2 as gate oxide was fabricated, which showed the good characteristic. The normalized maximum gm is 43 mS/mm at VG = 1.3 V for VDS fixed at 1 V. The maximum calculated £gFE of 348 cm2/V¡Es at VDS = 1 V is obtained.
| Identifer | oai:union.ndltd.org:NSYSU/oai:NSYSU:etd-1219107-132445 |
| Date | 19 December 2007 |
| Creators | Yen, Chih-Feng |
| Contributors | Chien-Jung Huang, Yu-Hao Yang, Wen-Chao Liu, Kuang-Chih Huang, Ming-Kwei Lee, Chao-Fu Yu, I-Kai Lo |
| Publisher | NSYSU |
| Source Sets | NSYSU Electronic Thesis and Dissertation Archive |
| Language | English |
| Detected Language | English |
| Type | text |
| Format | application/pdf |
| Source | http://etd.lib.nsysu.edu.tw/ETD-db/ETD-search/view_etd?URN=etd-1219107-132445 |
| Rights | restricted, Copyright information available at source archive |
Page generated in 0.0019 seconds