When central HVAC systems are under commercial operation, all operational parameters, including chilled water supply temperature, return water temperature, chilled water flow rate, and power consumption as the key factors in affecting system energy efficiency.However, in Taiwan there is still lacking of the regression equations of chillers under local weather conditions, and has to rely on manual operation based on experiences. This is also the major short-comings in implementing TAB, and is the best way to renovate the green buildings to make them more intelligent. In this study, theoretical analysis and experimental investigation will be applied simultaneously. In selecting cases from the BeeUp program, actual operational data including COP can be fitted into experimental model to facilitate TAB engineering via BEMS system, in achieving system efficiency. Through the execution of this project, it is identified that the exhibition buildings with 10 hours cooling load, can achieve 7% energy savings. The good result obtained in this project , including the thermal energy storage HVAC system and the heat pump system can be widely adapted to obtain significant energy conservation effect.

Being located in subtropical area, the weather in Taiwan is hot and humid which imposing huge cooling load on buildings. Conventionally, central air-conditioning plants were designed using refrigerant compressors to make chilled water, and then pumped through the zone pumps to meet the cooling load, providing air-conditioning by Fan Coil Unit (FCU) or Air-Handling Units (AHU) by ductwork. To meet the varying cooling demand, two important systems were developed for energy savings, namely, the Variable Water Volume (VWV) system, and the Variable Air Volume (VAV) system, which has been widely adapted in Taiwan area. The working principle is mainly devoted to adjusting the volume of the chilled water and/or air volume delivered through inverter-driven pimps and fans to achieve energy saving. On the other hand, recently in Japan, an important energy-saving air-conditioning system has been developed which directly varying the refrigerant flow rate to meet the varying cooling demand by inverter-driven compressors, named VRV system. Comparative to the conventional air-conditioning system, the heat exchange mechanism of the VRV system has been effectively enhanced by direct exchange of the refrigerant and the cool air, which is in effect a combination of the VWV and VAV system. It provided huge energy saving potential for the application on buildings with moderate cooling loads, such as 100 USRT or so. It is the goal of this research project, to evaluate the performance of the VRV system in Taiwan¡¦s hot and humid climate, by performing full-scale experimental investigation so that energy savings effect can be validated quantitatively. Since VRV system is fairly new in Taiwan, the validation of the system performance under local weather condition is of particular importance. It is anticipated that through the changing of the operation conditions, such as different outdoor conditions, various partial load conditions, and different scheduling of the VRV system, the power consumption of the VRV vs. conventional system can be compared precisely and quantitatively. These experimental data will, in turn, provides valuable reference to the establishment of the building energy consumption index in Taiwan, which outwits the direct adoption of the foreign data such as from Japan, in achieving a much reliable database.

none

In this study laminar forced film condensation of vapor flowing in cross-flow direction through the annular space between two concentric cylinders was investigated numerically. To achieve this, governing equations of the vapor and the condensate flow in cross-flow direction between two concentric cylinders were developed. After obtaining the equations in integral forms by using the finite difference technique the vapor boundary layer thicknesses on the inner and outer cylinders and the condensate layer thickness was obtained as a function of the angular position on the cylinders. It was assumed that the condensation took place on the outer surface of the inner cylinder only and the outer cylinder was assumed to be insulated. The computer program developed is capable to calculate the condensate film thickness, vapor boundary layer thickness, the heat flux and the heat transfer coefficient and the interface velocity between the condensate and the vapor layer as a function of the angular position on the cylinders. Effects of changing the free stream velocity flowing in the channel, the radius of the inner cylinder, the temperature difference between the saturated vapor and the wall and the annular space between the concentric cylinders were investigated numerically by using the computer program and the results were presented graphically. Results showed that by increasing the free stream velocity of the vapor in the core, the film thickness decreased and by increasing the radius of the inner cylinder, the temperature difference between the saturated vapor and the wall and the annular space, the film thickness increased.

This thesis presents energy, exergy and economic analyses of the heating system of an existing building, the Konya Central Informatics Technical High School. The heat requirement for each room of the building is found by calculating heat losses. Radiator lengths that can provide the heat requirements are selected. For the exergy analysis, the system is divided into three parts: Heat generator, radiators and rooms. Comparisons are made according to minimum outdoor temperature, insulation quality of the structural elements, fuel type, heating water temperature and heat generator type (boiler, heat pump, cogeneration unit with heat pump) to see their effects on energy usage, exergy consumption, capital costs and annual operating cost of the system. Results show that the largest heat loss is due to infiltration but it should not be reduced because of the fresh air requirement. Minimum energy usage, exergy consumptions and annual operating cost is achieved by using the cogeneration unit with the heat pump. However, due to high capital cost it has a long payback period (45.3 years). The shortest payback period (3.2 years) is calculated for upgrading the windows to 4 mm double glass panes and 12 mm stagnant air gap.

In this study, energy conservation potential of appropriate passive cooling and basic heat avoidance strategies were investigated for hot and humid climates. Within this framework, thermal behavior of a case study building that is situated in Cyprus was assessed by collecting temperature and relative humidity data from various rooms of the building during certain days in August. Then, by using feasible simulation strategies of the software tool Summer-Building, the effectiveness of passive cooling measures in reducing energy consumption were examined, for summer months. In this context, the case study building was re-evaluated by applying natural ventilation, night ventilation and ground cooling strategies as well as solar control and shading devices as overhangs and side fins. Consequently, based on the results of the evaluation model, it was found that the proposed passive cooling strategies and basic heat avoidance concepts could provide more than 50 % energy conservation, relative to the completely air conditioned reference building, between 1-15 August 2007.

In this study simultaneously developing single phase, laminar and incompressible flow in a micro gap between parallel plates is numerically analyzed by including the effect of variation in thermal conductivity and viscosity with temperature. Variable property solutions for continuity, momentum and energy equations are performed in a coupled manner, for air as a Newtonian fluid. In these analyses the rarefaction effect, which is important for the slip flow regime, is taken into account by imposing slip velocity and temperature jump boundary conditions to the wall boundaries. Mainly, the influence of viscous dissipation, axial conduction, geometric parameters and rarefaction on the property variation effect is aimed to be discussed in detail. Therefore, the effects of variable thermal conductivity and viscosity are investigated simultaneously with the effects of rarefaction, geometric parameters, viscous dissipation and axial conduction. The difference between constant and variable solutions in terms of heat transfer characteristics is related to the effects of viscous dissipation axial conduction and rarefaction. According to results, property variation is substantially effective in the entrance region where temperature and velocity gradients are high. On the other hand, property variation effects are not significant for fully developed air flows in microchannel.

A novel complementary metal oxide semiconductor (CMOS) compatible microchannel heat sink is designed, fabricated, and tested for electronic cooling applications. The proposed microchannel heat sink requires no design change of the electronic circuitry underneath. Therefore, microchannels can be fabricated on top of the finished CMOS wafers by just adding a few more steps to the fabrication flow. Combining polymer (parylene C) and metal (copper) structures, a high performance microchannel heat sink can be easily manufactured on top of the electronic circuits, forming a monolithic cooling system. In the design stage, computer simulations of the microchannels with several different dimensions have been performed. Microchannels made of only parylene showed poor heat transfer performance as expected since the thermal conductivity of parylene C is very low. Therefore an alternative design comprising structural parylene layer and embedded metal layers has been modeled. Copper is selected as the metal due to its simple fabrication and very good thermal properties. The results showed that the higher the copper surface area the better the thermal performance of the heat sinks. Based on the modeling results, the final test structures are designed with full copper sidewalls with a parylene top wall. Several different microchannel test chips have been fabricated in METU-MEMS Research &amp / Application Center cleanroom facilities. The devices are tested with different flow rates and heat loads. During the tests, it was shown that the test devices can remove about 126 W/cm2 heat flux from the chip surface while keeping the chip temperature at around 90&deg / C with a coolant flow rate of 500 &mu / l/min per channel.

This thesis investigates the refrigerant (R-134a) flow in a minitube experimentally. The small scale heat transfer is a relatively new research area and has been in favor since the end of 1970&rsquo / s. Refrigerant flow in mini- and microscale media is a potential enhancement factor for refrigeration technology in the future. For the forthcoming developments and progresses, experimental studies are invaluable in terms of having an insight and contributing to the establishment of infrastructure in the field in addition to leading the numerical and theoretical approaches. The studies in the literature show that low mass flow rate and constant wall temperature approach in minitubes and minichannels were not among the main areas of interest. Therefore, an experimental set-up was prepared in order to perform experiments of two-phase refrigerant flow in a 1.65 mm diameter copper minitube with the constant wall temperature approach. The design, preparation, and modifications of the experimental set-up are explained in this thesis. Two-phase flow and quality arrangements were done by pre-heating the refrigerant at saturation pressure and the constant wall temperature was achieved by a secondary cycle with water and ethylene glycol mixture as the working fluid. The heat transfer coefficient and the pressure drop for the two-phase flow with varying quality values and saturation temperatures of the refrigerant were calculated and compared with the results available in literature.

This paper seeks to develop a framework for the successful implementation of energy retrofit projects in all settings, including those with the non-traditional structure and unique needs of some non-profit organizations. This will be accomplished using researched strategies for overcoming commonly associated challenges along with experiences gained through a real-life case study involving a multi-facility retrofit project in Atlanta's largest public park, Chastain Park. The framework includes the application of research based solutions for common challenges as well as specific strategies for the translation of collected data into an actual scope of work, methods for the collection of bids and selection of contractor(s), the importance of and methods for communicating amongst stakeholders, and the need for a dedicated project manager on site at all times.