Sulfide soils are silty soils, often found in saturated conditions, under the groundwater level. Characteristics of these soils, including particle size distribution and consistency limits along with chemical composition and environmental properties, cause excavation to be necessary for construction purposes. The excavated sulfide soil usually is transported and deposited in landfills. These soils are either deposited in saturated conditions or chemical buffers are added to the soil to prevent acidification. Special conditions of these landfills complicate the disposal procedure and the landfill maintenance which makes those financially expensive. Reusing sulfide soil in construction is a solution to reduce the expenses related to the management of sulfide soils. Since the mechanical properties of these soils are not suitable for construction purposes, the first step is to improve soil characteristics to the level that fulfills the needs of construction applications. One solution to improve the mechanical properties of the soil is adding a binder to the soil. The main focus of the research was to improve the mechanical properties of soil. The research activities were divided into two parts. The first part was conducted in a laboratory environment to develop mixtures, while the second focused on transferring the results to field conditions. The laboratory tests included mixing soil and binder i.e., cement was added to the soil at different percentages to evaluate the soil improvement. An unconfined compressive strength (UCS) test was conducted on the stabilized sample to evaluate the efficiency of the stabilization. The resultsof UCS for the stabilized samples were compared. Since the soil contains a high amount of water, the traditional sample preparation was not suitable. Therefore, an alternative method was developed and evaluated. Moreover, the effect of curing time on the strength and consistency limit of stabilized samples was evaluated. At last, the effect of different variables, including porosity, binder content and initial water content, on the UCS of soil was investigated to identify potential correlation between UCS and different soil variables. The results of the tests showed that adding a binder, regardless of the type of sulfide soil, positively affects the UCS of prepared samples and increasing the curing time increased the UCS of the samples. At higher cement content, the effect of curing time was more significant. Also, it was shown that at higher water content, the effect of binder is lower in comparison with the same soil at lower water content. By lowering the water content, the strength of stabilized soil reaches a maximum and drying further the soil, below the optimum water content, led to strength reduction. A correlation between UCS of sample and porosity/binder ratio was employed to predict the strength behavior of stabilized soil based on variables such as porosity, initial water content and binder dosage. In order to evaluate if laboratory results can be applied to geotechnical applications, the second part of this research included a field mixing experiment for a large-scale mixture of soil and cement. The effect of the mixing procedure with common equipment on the homogeneity of industrial-size mixture was investigated. A sampling strategy for collecting representative samples of mixture was selected and assessed. the number of mixing steps and the effect of binder dosage on the uniformity of samples were studied. Results of UCS of samples prepared from field and laboratory mixture were compared and evaluated. A field evaluation was conducted to determine the quality of the mixture and how many mixing steps are required to reduce variability between samples. Two different percentages of binder were added to the 5 Tons of soil. The UCS test samples were prepared from the soil-cement mixture in the same way as they were prepared in the laboratory and cured for a specific time. The UCS test was conducted on cured samples. The test results were compared to evaluate the mixture homogeneity in the field. The results showed that homogeneous mixtures can be obtained in the field with the available equipment. Assessing the sampling strategy showed that increasing the sampling sections from 5 to 12 and preparing single UCS sample from the collected soil provides representative samples from the soil mixture pile. Additionally, it was shown that by increasing mixing steps from 2 to 3, it was possible to eliminate samples with notable lower strength than average UCS. A greater number of mixing steps improves homogeneity while reducing the average UCS. It was found that mixing soil and binder in the laboratory improves strength better than mixing them in the field. When applying laboratory results to field design, this point must be taken into account.

The purpose of this research was to investigate the effects of reclaimed asphalt pavement (RAP) content and cement content on the strength and durability of recycled aggregate base materials. Specifically, the unconfined compressive strength (UCS) and final dielectric value in the Tube Suction Test (TST) were measured in a full-factorial experimental design including five RAP contents, five cement contents, and three replicate specimens of each possible treatment. Specimen mixtures consisted of 0, 25, 50, 75, or 100 percent RAP and 0.0, 0.5, 1.0, 1.5, or 2.0 percent Type I/II Portland cement. Both the RAP and base materials were sampled from the I-84 pavement reconstruction project performed in Weber Canyon near Morgan, Utah, during the summers of 2004 and 2005. The laboratory testing procedures consisted of material characterizations, specimen preparation, and subjection of the specimens to strength and durability testing, and the data were evaluated using analysis of variance (ANOVA) testing. Both the RAP and base materials included in this research were determined to be non-plastic, and the AASHTO and Unified soil classifications for the RAP material were determined to be A-1-a and SM (well-graded sand with gravel), respectively, and for the base material they were A-1-a and SW-SM (well-graded sand with silt and gravel), respectively. The optimum moisture contents (OMCs) for the blended materials were between 5.6 and 6.6 percent, and maximum dry density (MDD) values were between 129.7 and 135.5 lb/ft3. In both cases, decreasing values were associated with increasing RAP contents. The results of the ANOVA performed on the UCS data indicate that UCS decreases from 425 to 208 psi as RAP content increases from 0 to 100 percent and increases from 63 to 564 psi as cement content increases from 0.0 to 2.0 percent. Similarly, the final dielectric value decreases from 14.9 to 6.1 as RAP content increases from 0 to 100 percent and decreases from 14.0 to 5.8 as cement content increases from 0.0 to 2.0 percent. With design criteria requiring 7-day UCS values between 300 and 400 psi and final dielectric values less than 10 in the TST, the results of this research suggest that milling plans should be utilized to achieve RAP contents in the range of 50 to 75 percent, and a cement content of 1.0 percent should be specified for this material. Cement contents less than 1.0 percent are not sufficient to stabilize the material, and greater cement contents may cause cracking. Because control of the actual cement content in the field depends on the contractor's equipment and skill, inspection protocols should be implemented during construction to ensure high-quality work. Additional recommendations are associated with the construction process. The specimens prepared in this research were compacted to relative densities of 100 percent using modified Proctor energy. Therefore, field compaction levels must approach these density values if the same material properties are to be achieved. In addition, all specimens tested in this study were cured at 100 percent relative humidity. Following compaction in the field, cement-treated layers should be moistened frequently during the first few days after construction or promptly sealed with a prime coat or wearing surface to ensure that the cement continues to hydrate. Variability in RAP and cement contents should also be minimized to achieve consistent material properties.

The use of recycled concrete material (RCM) as pavement base material is a promising but unproven technique for road rehabilitation and construction. A telephone survey conducted to investigate the state of the practice concerning RCM usage in Utah County revealed that RCM is infrequently used in this application due primarily to a lack of practical knowledge about the engineering properties of the material. Therefore, this research was aimed at evaluating the physical properties, strength parameters, and durability characteristics of both demolition and haul-back sources of RCM available in Utah County for use as pavement base material. The study included extensive laboratory and field testing. Laboratory tests included California bearing ratio (CBR), unconfined compressive strength (UCS), stiffness, freeze-thaw cycling, moisture susceptibility, abrasion, salinity, and alkalinity evaluations. Non-destructive testing was utilized in the field to monitor seasonal variation in stiffness of an RCM pavement base layer over a 1-year period. The testing included a dynamic cone penetrometer, ground-penetrating radar, a heavy Clegg impact soil tester, a soil stiffness gauge, and a portable falling-weight deflectometer. The laboratory testing indicated that the demolition material exhibited lower strength and stiffness than the haul-back material and reduced UCS loss after freeze-thaw cycling. However, the demolition material received a moisture susceptibility rating of good in the tube suction test, while the haul-back material was rated as marginal. Both materials exhibited self-cementing effects that led to approximately 180 percent increases in UCS over a 7-day curing period. Seven-day UCS values were 1260 kPa and 1820 kPa for the demolition and haul-back materials, respectively, and corresponding CBR values were 22 and 55. The field monitoring demonstrated that the RCM base layer was susceptible to stiffness changes due primarily to changes in moisture. In its saturated state during spring testing, the site experienced CBR and stiffness losses of up to 60 percent compared to summer-time values. RCM compares well with typical pavement base materials in many respects. Given the laboratory and field data developed in this research, engineers should be able to estimate the strength and durability parameters of RCM needed for pavement design.

Frost heave is a primary mechanism of pavement distress in cold regions. The distress exhibited is dependent on the frost susceptibility of the soil within the depth of frost penetration, the availability of subsurface water, and the duration of freezing surface temperatures. Cement stabilization is one technique used to mitigate the effects of frost heave. The tube suction test (TST) is one possible method for determining the frost susceptibility of soils in the laboratory. The purpose of this research was to assess the utility of the TST for identifying non-frost-susceptible (NFS) materials stabilized with cement. This research investigated two aggregate base materials from Alaska that have exhibited negligible frost susceptibility in the field. The unconfined compressive strength (UCS), final dielectric value in the TST, and frost heave at three levels of cement treatment and in the untreated condition were evaluated for both materials. The data collected in this research indicate that, for the two known NFS materials included in this study, the TST is a good indicator of frost heave behavior. The total heave of the untreated materials was approximately 0.15 in. at the conclusion of the 10-day freezing period, which classifies these materials as NFS according to the U.S Army Corp of Engineers. Both materials had final dielectric values of less than 10 in the TST, indicating a superior moisture susceptibility rating. The results of this research suggest that the TST should be considered for identifying NFS materials, including those stabilized with cement. Additional testing should be performed on known NFS materials stabilized with cement and other additives to further assess the validity of using the TST to differentiate between frost-susceptible and NFS materials. Consistent with previous studies, this research indicates that, once a sufficient amount of cement has been added to significantly reduce frost heave, additional cement has only a marginal effect on further reduction. Therefore, to avoid unnecessary expense in construction, the minimum cement content required for preventing frost heave should be identified through laboratory testing and specified by the engineer. In this work, UCS values ranging between 200 psi and 400 psi after a 7-day cure were typically associated with this minimum cement content. Because the scope of this research is limited to two aggregate base materials, further testing is also necessary to validate this finding.

The ENDURA block system is a dry-stack surface-bonded masonry system. Typical masonry construction uses thin-set mortar in the bed joints to provide a bearing surface for the blocks while the ENDURA system typically relies on shims and a surface bonding coat to ensure that the wall is level and plumb and to provide stability. Typical ENDURA block walls are built with the reinforcement placed eccentrically in the walls. Testing was performed on ten walls in order to determine axial capacity. The walls were ten feet high by eight feet wide. Each of the walls was built using a different configuration of block type, reinforcement spacing, and amount of grout. A steel frame with two hydraulic jacks was used to apply vertical load to the top of the walls. Three conclusions were drawn from the axial testing performed. First, typical ENDURA block walls built without thin set mortar in the bed joints have similar axial capacity to walls built with the thin set mortar. Second, walls built with un-reinforced cells grouted resisted significantly more load than walls built with only the reinforced cells grouted. Third, more research is required in order to establish a control and to determine whether the eccentrically placed rebar has a significant effect on the axial capacity of the walls.

Interlocking Cross Laminated Timber (ICLT) wall panels are a new wood construction product similar to Cross Laminated Timber panels. Besides being an innovative structural system, they also utilize beetle killed timber from many of the forests that have been devastated by the Mountain Pine Beetle. Three tests were performed on three ply ICLT panels measuring 8 feet (2.44m) wide, 8 feet (2.44m) tall and 8.5 inches (21.6cm) thick to determine the racking, flexural and axial strengths of the wall panels. After each test was performed the walls were disassembled and investigated for cause of failure. Using the data from the tests as a benchmark, simple analytical models to predict the design capacities of the walls for racking, flexural, and axial strengths were established. The analytical models for racking strength, flexural strength and axial strength predicted reasonably well the measured strength values. Additional testing is necessary to increase the available database, further validate the analytical models developed, better understand the structural performance of ICLT panels, and establish acceptable design methodology for ICLT wall panels.

The objectives of this research were to 1) monitor in-situ moisture and diffusivity for both conventional concrete and concrete containing pre-wetted lightweight fine aggregate (LWFA), 2) compare deck performance in terms of early-age cracking, compressive strength, and chloride ingress, and 3) compare concrete properties in terms of compressive strength, chloride permeability, elastic modulus, and water content in the laboratory using cylinders cast in the field at the time of deck construction. The research involved field and laboratory evaluations of four newly constructed bridge decks located in northern Utah, two constructed using conventional concrete and two constructed using pre-wetted LWFA to promote internal curing. Data from sensors embedded in the concrete decks indicate that the moisture content of the internally cured concrete was consistently 1.5 to 4 percentage points higher than the moisture content of the conventional concrete for the first 6 months following deck construction. By 1 year, however, the internally cured concrete showed little difference in moisture content compared to the conventional concrete. While the internally cured concrete decks had a higher average moisture content, the electrical conductivity values were not consistently higher than those measured on the conventional concrete decks during the first approximately 8 to 10 months. However, after 8 to 10 months, both internally cured concrete decks exhibited higher electrical conductivity values than those measured on the conventional concrete decks. Laboratory compressive strength data indicate that, for the first 6 months following deck construction, the two concrete mixtures exhibited very similar strength gain characteristics. However, at 1 year, the conventional concrete was stronger by an average of 12.9 percent, or nearly 900 psi, than the internally cured concrete. In rapid chloride permeability testing, the internally cured concrete consistently passed between 13.1 and 17.5 percent less current than that passed by the conventional concrete. Laboratory free-free resonant testing at 1 year showed that the modulus of the internally cured concrete was 3.9 percent lower, on average, than that of the conventional concrete. For the tested specimens, the moisture content of the internally cured concrete was 0.5 percentage points higher, on average, than that of the conventional concrete. In the field, Schmidt rebound hammer testing showed that the internally cured concrete was neither consistently stronger nor weaker than the conventional concrete. On average, the internally cured concrete exhibited higher chloride concentrations than the conventional concrete. On average, the conventional concrete bridge decks had 4.6, 21.5, and 2.8 times more cracking than the internally cured concrete decks at 5 months, 8 months, and 1 year, respectively. At 1 year, very distinctive reflection cracks from the joints between the underlying pre-cast half-deck panels were observed on all of the decks.

Full-depth reclamation (FDR) is an increasingly common technique that is used to rehabilitate flexible pavements. Implementation of FDR on rehabilitation projects produces several desirable benefits. However, these benefits are not fully realized due to the fact that state department of transportation specifications typically limit the reclaimed asphalt pavement (RAP) content of pavement base material to 50 percent. The objective of this research was to evaluate the effects of RAP content, cement content, temperature, curing time, curing condition, and moisture state on the strength, stiffness, and deformation characteristics of cement-treated base (CTB) mixtures containing high percentages of RAP.For this research, one aggregate base material and one RAP material were used for all samples. RAP content ranged from 0 to 100 percent in increments of 25 percent, and low, medium, and high cement levels corresponding to 7-day unconfined compressive strength (UCS) values of 200, 400, and 600 psi, respectively, were selected for testing. Moisture-density, UCS, resilient modulus, and permanent deformation tests were performed for various combinations of factors, and several statistical analyses were utilized to evaluate the results of the UCS, resilient modulus, and permanent deformation testing.The results of this work show that CTB containing RAP can be made to achieve 7-day UCS values approaching 600 psi regardless of RAP content. With regards to stiffness, the data collected in this study indicate that the resilient modulus of CTB containing RAP is affected by temperature in the range from 72 to 140°F for the low cement level. Permanent deformation of CTB containing RAP is significantly affected by RAP content and cement level at the test temperature of 140°F. At the low cement level, temperature is also a significant variable. As the 7-day UCS reaches approximately 400 psi, permanent deformation is reduced to negligible quantities. The results of this research indicate that the inverse relationship observed between permanent deformation and 7-day UCS is statistically significant.Given that the principle conclusion from this work is that CTB with high RAP contents can perform satisfactorily as a base material when a sufficient amount of cement is applied, agencies currently specifying limits on the percentage of RAP that can be used as a part of reclaimed base material in the FDR process should reevaluate their policies and specifications with the goal of allowing the use of high RAP contents where appropriate.

No description available.

Percent within limits (PWL) is a commonly used quality control/quality assurance measure of highway pavement materials and construction, and it is a popular index for adjusting pay factors. However, PWL is based on the assumption of normal distribution of quality characteristics (e.g., concrete compressive strength and asphalt air voids). Skewness and kurtosis, which are common forms of statistical nonnormal distributions, can potentially bias the acceptance pay factor calculations. To examine this potential pay bias, simulations were performed to investigate the magnitude and the direction (overestimation or underestimation) of pay factor calculations. The study revealed that for both one-sided and two-sided specification limits, bias in pay factors not only did vary in magnitude but also reversed in direction over various ranges of PWL. These analyses showed that for a one-sided upper specification limit, on average, a positive skewness and kurtosis can underestimate the pay factor of an acceptable quality level population by 0.90%, and overestimates a rejectable quality level population by 3.8%. This leads to falsely penalizing acceptable products and rewarding bad products. The same was true for two-sided limits, which again varied based upon the percent of defective materials at the tails of the distribution. This is a very important issue because these biases in pay factors can easily upset the relative profit margins of the contractor. Furthermore, this may not be easily detectable without a detailed and sophisticated analysis as outlined in this paper. For multiple quality characteristics based pay factors, analyses showed that the combined magnitude of these biases was not linearly cumulative. Findings of the study indicate that bias in pay was higher for lots with fewer sublots and higher skewness and kurtosis.