The research on electrochemical sensor applications in combination with application-defined electronic circuits is a very fast developing field of modern sensorics. Device designing of unique integrated systems with specific properties and parameters is now becoming the everyday practice for producers of devices based on the latest technology progress in microelectronics. In the process of realization of a new device type, the main objective consists in increasing the possibility of detecting very low concentrations of heavy metals in the given chemical solution, extending the signal-to-noise ratio, and measuring the potential of a sensor. The general aim of this Master’s thesis is to design the topology of a sensor based on the thick film technology, to materialize the sensor, and to make experimental measurement using the sensor prototype. The practical reason for basing the measurement on the application of this thick film sensor is to find out whether the operational integration of the sensor and the circuit has been achieved according to the original hypothesis. Importantly, it is also necessary to determine whether the reproducibility of measured results has been reached. The innovative aspect of the created device consists in the improvement of output characteristics given by the integration of ASIC (IMAM CHIP). The integration of ASIC on the surface of the sensor eliminates the huge parasitic influence that affects the accuracy of measurement.

This work deals with investigation of intercalation of alkaline metals in electrochromic devices by the help of the quartz crystal microbalance method. The general aim is to investigate the influence of molar mass and resistance on properties of vanadium pentoxide and tungsten trioxide electrochromic films. The main measuring method used for investigating of interacalation of sodium and lithium ions into these films is the cyclic voltammetry. Drawn graphs reveals that sodium and lithium ions shows different qualities during intercalation, particularly in participation of solvent, therefore, in the influence of molar mass and in structural changes in the films.

This thesis is involved in basical properties of electrode materials for alkaline accumulators. This thesis describes the possibilities of capacity stabilisation of nickel electrode to be stable for highest number of cycles. Thesis also consider modification of properties of electrode materials on the base of nickel hydroxide by using dopes (aluminum, manganese). Measuration proceeded on the thin film electrodes created by electrodeposition. Measuration of properties of electrodes proceeded by cyclic voltammetry and frequency analyzis.

In recent years (Of late year)microelectronic technology significantly affected in the field of sensor technology, especially in the field of electrochemical sensors. This thesis deals with design and construction of thick-film voltammetric sensors array. The reason for proposal of voltammetric sensors array is to increase of speed, increase the accuracy and extension possibilities measurement compared with common systems.By reason of increase of sensitivity of these sensors it is efficient use the potentiostat chip for measurement output signal. Created sensors must fulfill the specified parameters and also requirements of thick-film technology. Next step is design the basic blocks of electronic circuit used to evaluate the measured values.

This master's thesis is concerned with the influence of aluminate ions added in various concentrations into the structure of nicel hydroxide that creates Ni-Cd accumulators positive electrode active mass basis nowadays. Nicel hydroxide occurs in two basic modifications ? and ß. Nowadays used ß modification reaches low capacity in comparison with ? modification. The disadvantage of ? modification is its instability and gradual degradation to ß modification. The aim of this diploma paper is to select the optimal amount of aluminate additives into the structure of nicel hydroxide with regard to electrochemical efficiency, stability, and degradation degree of the accumulated layer.

Master’s thesis is deals with the effect of carbon additives on the positive electrode in the NiCd batteries. It examines whether the positive electrode material enrichment of carbon additives to achieve improved internal parameters of conductivity and better contact with the electrode materials in a discharged. Galvanostatic cycling and electro-chemical impedance spectroscopy (EIS) are used for evaluation of graphite aditives.

The aim of this work is the thick-film electrochemical sensor characterization. In the theoretical part, the thesis describes sensor, three-electrode system, characterization electrode using cyclic voltammetry and electrode pretreatment methods. The experimental part compares the results of cyclic voltammetry of bare carbon electrodes, chemically pre-treated electrodes, electrochemically pre-treated electrodes and electrodes modified by plasma oxidation.

MSc (Chemistry) / Department of Chemistry

Eine Reihe 3-(p-X-phenyl)-Thiophenmonomeren (X = -H, -CH3, -OCH3, -COCH3, -COOC2H5, -NO2) wurde elektrochemisch polymerisiert, um Filme zu erhalten, die umkehrbar reduziert und oxidiert werden konnten (n-und p-dotiert wurden). Die Oxidationspotentiale der Monomere und die formalen Potentiale der n und p-Dotierprozesse der Polymere wurden mit Resonanz- und induktiven Effekten der Substituenten (Hammett konstanten) am Phenylring sowie semiempirisch errechneten Bildungswärmen der Monomereradikalkationen korreliert. Außerdem wurden die Oxidationspotentiale mit den Ionisierungspotentialen der Monomere verglichen, die über die Dichtefunktionialtheorie (DFT) errechnet wurden, die der Energie für das Erzeugen der Radikalkationen entsprechen. Um theoretische Grundlagen für die Einstufen-Bildung regioregulär -konjungierter Oligo- und Polythiophene zu erhalten, wurden die elektronischen Zustände von 3-Phenylthiophen-Derivaten anhand von Molekülorbitalberechnungen auf Grundlage der Dichtefunktionaltheorie mit Becke’s Drei-Parameter-Funktion (B3LYP), sowie mit den Basissätzen 6-31G(d) und 3-21G(d) erklärt. Die Reaktivität der Verknüpfung von mono- und oligo-3-Phenylthiophenen wurde von den berechneten ungepaarten Elektronenspindichten der entsprechenden Radikal-Anionen abgeleitet. Die Ionisierungspotentiale, die den Energien zur Erzeugung der Radikal-Anionen während der Oxidation entsprechen, wurden abgeschätzt. Die aus den 3-Phenylthiophenen entstandenen regioselektiven Hauptprodukte können gut durch die Größe der Spindichten erklärt werden. Da die Verknüpfungsreaktion an der zwei-Position des Thiophnrings (C-2) sterisch durch die Phenylgruppe und den Thiophenring gehindert ist, startet die Initiierung der 3-Phenylthiophene über die Bildung eines Kopf-Schwanz-Dimers. Folglich spielt das Kopf-Schwanz-Dimer eine wichtige Rolle bei den Wachstumsreaktionen der 3-Phenylthiophene. Die Ursache dafür liegt darin, dass das Kopf-Schwanz-Dimer in 5-Position die höchste Spin-Dichte besitzt und die Wahrscheinlichkeit einer Kopf-Kopf-Verknüpfung aufgrund der sterischen Hinderung zwischen dem Thiophenring und der Phenylgruppe gering ist. Polymerfilme von 3-Phenylthiophenderivaten, die durch elektrochemische Polymerisation synthetisiert wurden, sind in situ und ex situ durch Resonanz-Raman-Spektroskopie bei verschiedenen Anregungswellenlängen, sowie durch in situ und ex situ UV-Vis Spektroskopie analysiert wurden. Die Entwicklung der in situ UV-Vis-Spektren der Polymer von 3-Phenylthiophene nach der Dotierung wird durch ähnliche Eigenschaften gekennzeichnet, wie für viele Polythiophene mit einem hohen Grad der Konjugation beobachtet. Während der schrittweisen Oxidation der Poly-3-phenylthiophen Filme verringert sich die Intensität der Absorption wegen des Überganges bei 450-566 nm und ein neues ausgedehntes Absorptionsband, das auf (bi)polaron Zustände bezogen wird erscheint bei ungefähr 730-890 nm. Andererseits wird während der Oxidation (p-Dotierung) des Poly3-phenylthiophen Filmes eine blau/hypsochrome Verschiebung für beide Absorptionsbänder beobachtet . Es wird durch die Tatsache erklärt, dass ein Polymer eine Verteilung der Kettenlängen enthält und die längste Polymer kette (dessen Absorption bei niedriger Energie auftritt), bei niedrigeren Potentialen zu oxidieren beginnt. Die elektrochemischen Bandlücken der Derivate von 3-Phenylthiophen sind durch zyklische Voltametrie gemessen worden. Der Effekt der Substituenten auf den Oxidations-/Reduktions- potentiale wird besprochen. Bei Bandlücken, die durch zyklische Voltammetrie erhalten wurden, hat sich herausgestellt, dass sie im Allgemeinen höher liegen als optische Bandlücken. Erste Resultate der in situ Resonanz-Raman-Spektroskopie, von dem elektrochemisch erzeugten Polymerderivate von 3-Phenylthiophen Filmen auf einer Platinelektrode, in einer organischen Elektrolytlösung, werden berichtet. Beobachtete Raman Banden werden zugewiesen; gegründet auf diesen Resultaten werden die zuvor angenommenen molekularen Strukturen diskutiert. / A series of 3-(p-X-phenyl) thiophene monomers (X= –H, –CH3, –OCH3, –COCH3, –COOC2H5, –NO2) was electrochemically polymerized to furnish polymer films that could be reversibly reduced and oxidized (n- and p-doped). The oxidation potentials of the monomers and formal potentials of the n- and p-doping processes of polymers were correlated with resonance and inductive effects (Hammett constants) of the substituents on the phenyl ring as well as the semiempirically calculated heats of formation of the monomer radical cations. Moreover, the oxidation potentials of the monomers were correlated with the ionization potentials of the monomers calculated via density functional theory (DFT), which correspond to the energies for generating radical cations during oxidative processes. For obtaining a theoretical basis for the one-step formation of regioregular –conjugated oligo-and polythiophenes, the electronic states of 3-phenylthiophene derivatives were elucidated by molecular orbital calculations using density functional theory with the Becke-type three parameters functional (B3LYP), the 6-31G(d), and 3-21G(d) basis sets. The reactivity for coupling reaction of mono- and oligo-3-phenylthiophenes are inferred from the calculated unpaired electron spin densities of the respective radical cations, and the ionization potentials which correspond to the energies for generating radical cations during oxidative processes were estimated. The major regioselective products of the oligomerization of 3-phenylthiophene can be well understood in terms of the magnitude of spin densities. Since the steric hindrance between the phenyl group and thiophene ring interferes with the coupling reaction occurring between 2-postions (C–2) of thiophene rings, the initiating reaction of 3-phenylthiophene is generaton of a head-to-tail (HT) dimer. Thus, the head-to-tail (HT) dimer plays an important role in the propagation reactions of 3-phenylthiophene. This originates from the highest spin density at the 5- position of the HT dimer and low probability of the HH coupling due to the steric hindrance between thiophene ring and phenyl group. Polymer films of the 3-phenylthiophene derivatives prepared by electrochemical polymerization were analyzed, in situ and ex situ, with resonance Raman spectroscopy using several excitation wavelengths as well as in situ and ex situ UV-Vis-spectroscopy. The evolution of the in situ UV-Vis-spectra of poly 3-phenylthiophene derivatives upon doping is characterized by similar features as observed for many polythiophenes with high degree of conjugation. During stepwise oxidation of the poly-3-phenylthiophene films the intensity of the absorption due to the transition around 450–566 nm decreases and a new broad absorption band related to (bi)polaron states appears around 730-890 nm. On the other hand, during the oxidation (p-doping) of the poly-3-phenylthiophene films a blue/hypsochromic shift is observed for both absorption bands. It is explained by the fact that a polymer contains a distribution of chain lengths, and the longest polymer chains (the absorption of which occurs at lower energies) start to oxidize at lower potentials. The electrochemical bandgaps of 3-phenylthiophene derivatives have been measured by cyclic voltammetry. The effect of substituents on the oxidation / reduction potentials is discussed. Bandgaps obtained by cyclic voltammetry have been found to be in general higher than optical bandgaps. Preliminary results of in situ resonance Raman spectroscopy of electrochemically generated poly-3-phenylthiophene derivatives films on a platinum electrode exposed to an organic electrolyte solution are reported. Observed Raman bands are assigned; based on these results previously suggested molecular structures are discussed.

Tetrathiafulvalene derivatives are remarkable molecules, with various application, reported relatively recently. The radical cation of these compounds has very inter- esting optical, electronic, electrocatalytic superconducting and magnetic properties that have been intensively studied recently. Quantitative in-situ EPR voltammetric spectroelectrochemistry studies of 2-(2-hydroxyethylsulfanyl)-3-(benzylsulfanyl)-6,7- bis(octadecylsulphanyl)tetrathiafulvalene (TTF-Der3) have been carried out with the aim to confirm the oxidation sites, follow-up reactions (after the first electron transfer), and electrochemical behaviour. The diffusion process was confirmed by the depen- dence of current on the square root of the scan rate. It was claimed that the ratio of the number of generated radicals to transferred charge (electrons) for two representative TTF derivatives was determined to 5.5:500 for and 7:500 for TTF, indicating the follow- up reactions. Experiments were performed using the commercially available EPR standards, calibrated for this method (experimental setup). The latter was validated by quantitative EPR with standard 4-hydroxy-2,2,6,6-tetramethylpiperidin-1-oxyl radical concentration (1·10−4 mol dm−3). For the ratios the confidence interval was reported for the first time for TTF-Der3 it was...