Energy issues in the United States are currently receiving a very high priority. There is a strong desire to replace fossil fuels with alternative sources of energy since fuel prices are rising dramatically, and for the harming effect on the environment. Biomass is one of the most promising alternative sources of energy. In this study, hydrothermal liquefaction with alcohol co-solvents was applied on giant miscanthus (Miscanthus giganteus) feedstock. All liquefaction experiments were conducted in 5500 series Parr® reactor. The most important parameters that affect the liquefaction process were studied. The yield of the liquefaction process was determined gravimetrically and the produced bio-oils were characterized. Bio-oil obtained at the optimum conditions was upgraded using different solid acid catalysts and the chemical composition for the upgraded bio-oil was determined. In a new study, the solid acids were added directly during the liquefaction process to produce upgraded bio-oil in one liquefaction/upgrading step.

This study investigated In situ biodiesel production with supercritical methanol. A micro-algae based feedstock was used and obtained from a local water treatment plant situated just outside of Bethal, South Africa (S 26° 29’ 19.362” E 29° 27’ 11.552”). The wet feedstock was used as harvested with only the excess moisture being removed. Characterisation of the feedstock showed that a wide variety of macro-algae, micro-algae, cyanobacteria and bacterial species were present in the feedstock. The main algal species isolated from the feedstock were Nostoc sp. and Chlamydomonas. The feedstock was found to have a higher heating value (HHV) of 22 MJ.kg-1 and a lower heating value (LHV) of 16.03 MJ.kg-1 with an inherent moisture content of 270g.kg-1 feedstock. The protein and fat content of the feedstock was determined by the Agricultural Research Council (ARC) and found to be 370.1 g.kg-1 and 61.6 g.kg-1 on a moisture free basis respectively. The high protein and fat content gives a theoretical bio-yield of 430 wt%. The low lignin content and high cellulose and hemi-cellulose content indicated that the feedstock would be suitable for energy production. Three experimental sets were performed to determine the effect certain reaction parameters will have on the bio-char, bio-oil and biodiesel yields. The first set entailed hydrothermal liquefaction without the addition of methanol. The second set involved in situ biodiesel production with supercritical methanol, while both supercritical methanol and an acid catalyst were used during in situ biodiesel in the third set. For the first set of experiments the effect of temperature (240°C to 340°C in intervals of 20°C) on the crude bio-oil and bio-char yields were investigated. The highest bio-char yield was found to be 336g g char.kg-1 biomass at 280°C, while the highest crude bio-oil yield was 470.7 g crude bio-oil per kg biomass at 340°C. In the second set of experiments the dry biomass loading was kept constant at 500 g.kg-1 and the temperature varied (240°C to 300°C in intervals of 20°C) along with methanol to dry biomass ratio (1:1, 3:1 and 6:1). The optimum bio-oil yield of 597.1 g bio-oil per kg biomass for this set was found at 500 g.kg-1 biomass loading, 300°C and 3:1 methanol to dry biomass ratio. The highest bio-char yield was found to be 382.6 g bio-char.kg-1 biomass for a 1:1 methanol to dry biomass weight ratio set with 500 g.kg-1 biomass loading at 280°C. An increase in methanol ratio also led to an increase in crude bio-oil yields however the 3:1 methanol to dry biomass mass ratio was found to give the highest bio-oil yield and the purest biodiesel, with less unsaturated FAME. The 6:1 methanol to dry biomass mass ratio did however increase the FAME yield, which tends to show completion of the in situ production of biodiesel. This was also seen in the amount fatty acid methyl esters (FAME) present in the crude bio-oil as the degree of transesterification starts to increase with an increase in methanol. The FAME content was determined using gas chromatography (GC) and gas chromatography coupled to mass spectrometry (GC-MS). During the last set of experiments the temperature (260°C to 300°C in intervals of 20°C) and methanol to dry biomass ratio (1:1, 3:1 and 6:1) was varied at a constant catalyst loading of 1 wt% of the dry biomass. The optimum yields achieved were 627 g crude bio-oil per kg biomass and 376 g bio-char per kg biomass at 300°C and 280°C, respectively. These yields were achieved at 500 g.kg-1 biomass loading and 6:1 methanol ratio. Compared to the experiments where no catalyst was used, a slight increase in the yield was observed with the addition of an acid catalyst. This might be due to the base metals present in the feedstock that can lead to saponification during transesterification without the addition of an acid catalyst. An overall improvement in the extraction of crude bio-oil was observed with in situ production compared to hydrothermal liquefaction. During in situ liquefaction, the bio-oil yield increased by 150 g crude bio-oil per kg biomass higher, while the bio-char yields did not significantly vary at the optimum point of 280°C this finding has a significant value for green coal research. The highest HHV for the bio-char of 27 MJ.kg-1 +/- 0.17 MJ.kg-1 was found at 280°C and a 3:1 methanol ratio. The HHV of the bio-char decreases with an increase in temperature as more of the hydrocarbons are dissolved and form part of the bio-crude make-up. The highest HHV recorded for the crude bio-oil was 42 MJ.kg-1 at a 6:1 methanol ratio, a temperature of 300°C and an acid catalyst. The crude bio-oil HHV, which increased with an increase in temperature, is well within the specifications of the biodiesel standard (SANS, 1935). The highest FAME yield of 39.0 g.kg-1 was obtained using a 6:1 methanol ratio and a temperature of 300°C in the presence of an acid catalyst. The crude oil contained 49.0 g.kg-1 triglycerides with alkenes (C13, C15 and C17) making up the balance. The purest biodiesel yield was achieved at 3:1 methanol to dry biomass mass ratio, as it had the lowest yield unsaturated methyl esters. The overall FAME yield increased with an increase in methanol ratio. The derivatised FAME yields were the highest during hydrothermal liquefaction (55.0 g.kg-1 biomass). The in situ production of biodiesel from waste water clarifier effluent stream was found to be possible. Further investigation is needed into sufficient harvesting methods, including the optimum harvesting location, as this will result in fewer impurities in the stream and subsequent higher yields. / MIng (Chemical Engineering), North-West University, Potchefstroom Campus, 2015

This study investigated In situ biodiesel production with supercritical methanol. A micro-algae based feedstock was used and obtained from a local water treatment plant situated just outside of Bethal, South Africa (S 26° 29’ 19.362” E 29° 27’ 11.552”). The wet feedstock was used as harvested with only the excess moisture being removed. Characterisation of the feedstock showed that a wide variety of macro-algae, micro-algae, cyanobacteria and bacterial species were present in the feedstock. The main algal species isolated from the feedstock were Nostoc sp. and Chlamydomonas. The feedstock was found to have a higher heating value (HHV) of 22 MJ.kg-1 and a lower heating value (LHV) of 16.03 MJ.kg-1 with an inherent moisture content of 270g.kg-1 feedstock. The protein and fat content of the feedstock was determined by the Agricultural Research Council (ARC) and found to be 370.1 g.kg-1 and 61.6 g.kg-1 on a moisture free basis respectively. The high protein and fat content gives a theoretical bio-yield of 430 wt%. The low lignin content and high cellulose and hemi-cellulose content indicated that the feedstock would be suitable for energy production. Three experimental sets were performed to determine the effect certain reaction parameters will have on the bio-char, bio-oil and biodiesel yields. The first set entailed hydrothermal liquefaction without the addition of methanol. The second set involved in situ biodiesel production with supercritical methanol, while both supercritical methanol and an acid catalyst were used during in situ biodiesel in the third set. For the first set of experiments the effect of temperature (240°C to 340°C in intervals of 20°C) on the crude bio-oil and bio-char yields were investigated. The highest bio-char yield was found to be 336g g char.kg-1 biomass at 280°C, while the highest crude bio-oil yield was 470.7 g crude bio-oil per kg biomass at 340°C. In the second set of experiments the dry biomass loading was kept constant at 500 g.kg-1 and the temperature varied (240°C to 300°C in intervals of 20°C) along with methanol to dry biomass ratio (1:1, 3:1 and 6:1). The optimum bio-oil yield of 597.1 g bio-oil per kg biomass for this set was found at 500 g.kg-1 biomass loading, 300°C and 3:1 methanol to dry biomass ratio. The highest bio-char yield was found to be 382.6 g bio-char.kg-1 biomass for a 1:1 methanol to dry biomass weight ratio set with 500 g.kg-1 biomass loading at 280°C. An increase in methanol ratio also led to an increase in crude bio-oil yields however the 3:1 methanol to dry biomass mass ratio was found to give the highest bio-oil yield and the purest biodiesel, with less unsaturated FAME. The 6:1 methanol to dry biomass mass ratio did however increase the FAME yield, which tends to show completion of the in situ production of biodiesel. This was also seen in the amount fatty acid methyl esters (FAME) present in the crude bio-oil as the degree of transesterification starts to increase with an increase in methanol. The FAME content was determined using gas chromatography (GC) and gas chromatography coupled to mass spectrometry (GC-MS). During the last set of experiments the temperature (260°C to 300°C in intervals of 20°C) and methanol to dry biomass ratio (1:1, 3:1 and 6:1) was varied at a constant catalyst loading of 1 wt% of the dry biomass. The optimum yields achieved were 627 g crude bio-oil per kg biomass and 376 g bio-char per kg biomass at 300°C and 280°C, respectively. These yields were achieved at 500 g.kg-1 biomass loading and 6:1 methanol ratio. Compared to the experiments where no catalyst was used, a slight increase in the yield was observed with the addition of an acid catalyst. This might be due to the base metals present in the feedstock that can lead to saponification during transesterification without the addition of an acid catalyst. An overall improvement in the extraction of crude bio-oil was observed with in situ production compared to hydrothermal liquefaction. During in situ liquefaction, the bio-oil yield increased by 150 g crude bio-oil per kg biomass higher, while the bio-char yields did not significantly vary at the optimum point of 280°C this finding has a significant value for green coal research. The highest HHV for the bio-char of 27 MJ.kg-1 +/- 0.17 MJ.kg-1 was found at 280°C and a 3:1 methanol ratio. The HHV of the bio-char decreases with an increase in temperature as more of the hydrocarbons are dissolved and form part of the bio-crude make-up. The highest HHV recorded for the crude bio-oil was 42 MJ.kg-1 at a 6:1 methanol ratio, a temperature of 300°C and an acid catalyst. The crude bio-oil HHV, which increased with an increase in temperature, is well within the specifications of the biodiesel standard (SANS, 1935). The highest FAME yield of 39.0 g.kg-1 was obtained using a 6:1 methanol ratio and a temperature of 300°C in the presence of an acid catalyst. The crude oil contained 49.0 g.kg-1 triglycerides with alkenes (C13, C15 and C17) making up the balance. The purest biodiesel yield was achieved at 3:1 methanol to dry biomass mass ratio, as it had the lowest yield unsaturated methyl esters. The overall FAME yield increased with an increase in methanol ratio. The derivatised FAME yields were the highest during hydrothermal liquefaction (55.0 g.kg-1 biomass). The in situ production of biodiesel from waste water clarifier effluent stream was found to be possible. Further investigation is needed into sufficient harvesting methods, including the optimum harvesting location, as this will result in fewer impurities in the stream and subsequent higher yields. / MIng (Chemical Engineering), North-West University, Potchefstroom Campus, 2015

Microalgae have many desirable attributes as a renewable energy recourse. These include use of poor quality land, high yields, and it is not a food recourse. This research focusses on the energetic and environmental impact of processing microalgae into a renewable diesel. Two thermochemical bio-oil recovery processes are analyzed, pyrolysis and hydrothermal liquefaction (HTL). System boundaries include microalgae growth, dewatering, thermochemical bio-oil recovery, bio-oil stabilization, conversion to renewable diesel, and transportation to the pump. Two system models were developed, a small-scale experimental and an industrial-scale. The small-scale system model is based on experimental data and literature. The industrial-scale system model leverages the small scale system model with scaling and optimization to represent an industrial-scaled process. The HTL and pyrolysis pathways were evaluated based on net energy ratio (NER), defined here as energy consumed over energy produced, and global warming potential (GWP). NER results for biofuel production through the industrial-scaled HTL pathway were determined to be 1.23 with corresponding greenhouse gas (GHG) emissions of -11.4 g CO2 eq (MJ renewable diesel)-1. Biofuel production through the industrial-scaled pyrolysis pathway gives a NER of 2.27 and GHG emissions of 210 g CO2 eq (MJ renewable diesel)-1. For reference, conventional diesel has an NER of 0.2 and GHG emissions of 18.9 g CO2 eq MJ-1 with a similar system boundary. The large NER and GHG emissions associated with the pyrolysis pathway are attributed to feedstock drying requirements and combustion of co-products to improve system energetics. Process energetics with HTL and pyrolysis are not currently favorable for an industrial scaled system. However, processing of microalgae to biofuel with bio-oil recovery through HTL does produce a favorable environmental impact and a NER which is close to the breakeven point of one.

Uncertainty in the global energy market and negative environmental impacts associated with fossil fuels has led to renewed interest in alternative fuels. The scalability of new technologies and production pathways are critically being evaluated through economic feasibility studies and environmental impact assessments. This work investigated the conversion of agricultural wast, delactosed whey permeate (delac), with yeast fermentation for the generation of biofuel via hydrothermal liquefaction (HTL). The feasibility of the process was demonstrated at laboratory scale with data leveraged to validate systems models used to perform industrial-scale economic and environmental impact analyses. Results showed a minimum fuel selling point of $4.56 per gasoline gallon equivalent (CGE), a net energy ratio (NER), defined as energy required to process biofuel divided by energy in the biofuel produced, of 0.81 and greenhouse gas (GHG) emissions of 30.03 g CO2-eq MJ-1. High Production costs can be attributed to operational temperatures of HTL while the high lipid yields of the yeast counter these heating demands, resulting in a favorable NER. The operating conditions of both fermentation and HTL contributed to the majority of GHG emissions. Further discussion focuses on optimization of the process, on the metrics of TEA and LCA and the evaluation of the process, on the metrics of TEA and LCA, and the evaluation of the process through a sensitivity analysis that highlights areas for directed research to improve commercial feasibility.

A liquefação hidrotermal (HTL) é uma tecnologia muito utilizada para a conversão de diversos tipos de biomassa em Bio-óleo bruto; contudo, enquanto tal combustível é produzido uma fase aquosa (PHWW), rica em matéria orgânica e alguns compostos tóxicos, também é gerada, podendo ocasionar severos impactos ambientais negativos. O objetivo da presente pesquisa foi aplicar dois bio-adsorventes: in natura (BAA) e ativado quimicamente (BAAA), derivados da casca de amendoim, como pré-tratamentos da PHWW afim de melhorar sua biodegradabilidade anaeróbia. O carvão ativado granular (GAC) foi utilizado como adsorvente modelo para comparação. Os processos de adsorção foram otimizados com a utilização de desenhos compostos centrais rotacionais (DCCR), no quais as variáveis independentes foram: pH do adsorvato, temperatura e quantidade de (bio) adsorvente no meio. A porcentagem de remoção de DQO e do íon amônio foram as variáveis dependentes. Isotermas de adsorção foram obtidas em ensaios em batelada. Após realizado o estudo do processo de adsorção, o potencial metanogênico dos efluentes pré-tratados e do efluente in natura foi determinado. Esses ensaios foram conduzidos com três concentrações de PHWW (6,5%, 13% e 26%), com dois ensaios controle, um negativo e outro positivo. A pressão nos frascos reatores foi monitorada diariamente e a determinação da composição do biogás produzido foi realizada por cromatografia gasosa uma vez por semana. Os resultados para a processo adsortivo foram encorajadores, uma vez que cada bio-adsorvente testado foi otimizado para diferentes variáveis resposta: BAA (NH4+) e BAAA (DQO). Os ensaios anaeróbios mostraram que uma maior taxa de produção metanogênica, dos efluentes pré-tratados, pode estar ligada à modificação química da superfície nas cascas de amendoim. Foi possível concluir que a bio-adsorção se perfila como uma alternativa sustentável para o pré-tratamento de efluentes advindos da HTL de cianobactérias. / Hydrothermal liquefaction (HTL) is a technology widely used for the conversion of several types of biomass to bio-crude oil; however, while such a fuel is produced an aqueous phase (PHWW), rich in organic matter and some toxic compounds, is also generated and can cause severe negative environmental impacts. The objective of the present research was to apply two bio-adsorbents: peanut bio-adsorbent (PB) and activated peanut bio-adsorbent (APB), as pre-treatments of PHWW to improve their anaerobic biodegradability. Granular activated carbon (GAC) was used as an absorbent model for comparison. The adsorption process was optimized with the use of central rotational composite designs (DCCR), in which the independent variables were: pH of the adsorbate, temperature and amount of (bio) adsorbent in the medium. The percentage of COD removal and ammonium ion were the dependent variables. After the study of the adsorption process, the methanogenic potential of the pretreated effluents and raw PHWW was determined. These trials were conducted with three concentrations of PHWW (6.5%, 13% and 26%), with two control trials, one negative and one positive. The pressure in the reactor flasks was monitored daily and the composition of the biogas produced was determined by gas chromatography once a week. The results for the adsorption process were encouraging, and ach bio-adsorbent tested was optimized for different response variables: PB (NH4+) and APB (COD). The anaerobic assays showed that a higher rate of methanogenic production of pretreated effluents may be linked to the chemical modification of the surface in the peanut shells. It was possible to conclude that the bio adsorption is outlined as a sustainable alternative for the pretreatment of effluents coming from HTL.

abstract: The project aims at utilization of hydrothermal liquefaction (HTL) byproducts like biochar to grow microalgae. HTL is a promising method to convert wet algal biomasses into biofuels. The initial microalgae liquefaction at a temperature of 300 °C for 30 minute, converted 31.22 % of the Galdieria sulphuraria and 41.00 % of the Kirchneriella cornutum into biocrude. Upon changing the reactor from a 100 ml to a 250 ml reactor, the yield in biocrude increased to 31.48 % for G. sulphuraria and dropped to 38.05 % for K. cornutum. Further, energy recoveries based on calorific values of HTL products were seen to drop by about 5 % of the 100 ml calculated values in the larger reactor. Biochar from HTL of G. sulphuraria at 300 °C showed 15.98 and 5.27 % of phosphorous and nitrogen, respectively. HTL products from the biomass were analyzed for major elements through ICP-OES and CHNS/O. N and P are macronutrients that can be utilized in growing microalgae. This could reduce the operational demands in growing algae like, phosphorous mined to meet annual national demand for aviation fuel. Acidic leaching of these elements as phosphates and ammoniacal nitrogen was studied. Improved leaching of 49.49 % phosphorous and 95.71 % nitrogen was observed at 40 °C and pH 2.5 over a period of 7 days into the growth media. These conditions being ideal for growth of G. sulphuraria, leaching can be done in-situ to reduce overhead cost. Growth potential of G. sulphuraria in leached media was compared to a standard cyanidium media produced from inorganic chemicals. Initial inhibition studies were done in the leached media at 40 °C and 2-3 vol. % CO2 to observe a positive growth rate of 0.273 g L-1 day-1. Further, growth was compared to standard media with similar composition in a 96 well plate 50 μL microplate assay for 5 days. The growth rates in both media were comparable. Additionally, growth was confirmed in a 240 times larger tubular reactor in a Tissue Culture Roller drum apparatus. A better growth was observed in the leached cyanidium media as compared to the standard variant. / Dissertation/Thesis / Masters Thesis Chemical Engineering 2017

abstract: The continued reliance on fossil fuel for energy resources has proven to be unsustainable, leading to depletion of world reserves and emission of greenhouse gases during their combustion. Therefore, research initiatives to develop potentially carbon-neutral biofuels were given the highest importance. Hydrothermal liquefaction (HTL, a thermochemical conversion process) of microalgae is recognized as a favorable and efficient technique to produce liquid biofuels from wet feedstocks. In this work, three different microalgae (Kirchneriella sp., Galdieria sulphuraria, Micractinium sp.) grown and harvested at Arizona State University were hydrothermally liquefied to optimize their process conditions under different temperatures (200-375 °C), residence times (15-60 min), solids loadings (10-20 wt.%), and process pressures (9-24 MPa). A one-factor-at-a-time approach was employed, and comprehensive experiments were conducted at 10 % solid loadings and a residence time of 30 min. Co-liquefaction of Salicornia bigelovii Torr. (SL), Swine manure (SM) with Cyanidioschyzon merolae (CM) was tested for the presence of synergy. A positive synergistic effect was observed during the co-liquefaction of biomasses, where the experimental yield (32.95 wt.%) of biocrude oil was higher than the expected value (29.23 wt.% ). Co-liquefaction also led to an increase in the energy content of the co-liquefied biocrude oil and a higher energy recovery rate ( 88.55 %). The HTL biocrude was measured for energy content, elemental, and chemical composition using GC-MS. HTL aqueous phase was analyzed for potential co-products by spectrophotometric techniques and is rich in soluble carbohydrates, dissolved ammoniacal nitrogen, and phosphates. HTL biochar was studied for its nutrient content (nitrogen and phosphorous) and viability of its recovery to cultivate algae without any inhibition using the nutrient leaching. HTL biochar was also studied to produce hydrogen via pyrolysis using a membrane reactor at 500 °C, 1 atm, for 24 h to produce 5.93 wt.% gas. The gaseous product contains 45.7 mol % H2, 44.05 ml % CH4, and 10.25 mol % of CO. The versatile applications of HTL biochar were proposed from a detailed physicochemical characterization. The metal impurities in the algae, bio-oil, and biochar were quantified by ICP-OES where algae and biochar contain a large proportion of phosphorous and magnesium. / Dissertation/Thesis / Doctoral Dissertation Chemical Engineering 2020

O processo de liquefação hidrotermal (HTL) pode converter diversos tipos de biomassa em óleo bruto. Além do produto principal, é gerado um efluente (PHWW) com elevada carga orgânica, quantidades altas de nutrientes e compostos tóxicos. Para lidar com este tipo efluente tem-se sugerido a combinação de tratamentos físico-químicos e biológicos. O objetivo deste estudo foi avaliar a aplicação de processos oxidativos (por H2O2 e fotocatálise com TiO2) e digestão anaeróbia no tratamento do efluente da liquefação hidrotermal de Spirulina. Inicialmente caracterizou-se o efluente em termos de carga orgânica, nutrientes e compostos nitrogenados cíclicos (CNC). Posteriormente, avaliou-se a concentração de oxidante e o tempo de reação no processo de oxidação com H2O2. O tratamento fotocatalítico foi então avaliada no tratamento do efluente em questão, isoladamente, em sequência e combinada ao processo de oxidação por ação de H2O2. Finalmente combinaram-se os processos de oxidação por ação de H2O2 e digestão anaeróbia no tratamento de efluente de PHWW. O efluente da liquefação hidrotermal de Spirulina apresentou elevada carga orgânica, pH alcalino e concentrações altas de nutrientes (nitrogênio e fósforo). Verificou-se também a presença de CNC como pirazinas, δ-valerolactama, caprolactama e butirolactama. A aplicação do processo oxidativo por H2O2 no tratamento de PHWW apresentou efeitos positivos, principalmente para a descoloração que atingiu 93,8 %. A eficiência máxima de remoção de DQO foi de 15,3%. Foi percebida também redução nas concentrações dos CNC. A eficiência do processo de oxidação avançada por fotocatálise e H2O2 foi maior do que obtida quando estes processos foram aplicados separadamente. A aplicação dos processos combinados apresentou eficiência de remoção de cor e DQO semelhante às obtidas quando os processos foram aplicados em sequência, propiciando economia de tempo de reação. Por fim, verificou-se que a digestão anaeróbia do efluente pré-tratado com H2O2 apresentou maior produção de CH4 e remoção de matéria orgânica quando comparada com a digestão anaeróbia que o efluente in natura. Assim, conclui-se a utlização de processos oxidativos avançados ou a combinação da oxidação por H2O2 com a digestão anaeróbia são alternativas promissoras para o tratamento da PHWW. / The hydrothermal liquefaction process (HTL) can convert various types of biomass into bio-crude oil. In addition to the main product, wastewater (PHWW) is generated with high organic content, high amounts of nutrients and toxic compounds. To cope with this type of wastewater the combination of physicochemical and biological treatments has been suggested. The aim of this study was to evaluate the application of oxidative processes (using H2O2 and photocatalysis with TiO2) and anaerobic digestion in the treatment of hydrothermal liquefaction of Spirulina wastewater. Firstly, PHWW was characterized in terms of organic matter, nutrients and nitrogen heterocyclic compounds (CNC) concentrations. Secondly, the oxidant concentration and the reaction time in the oxidation process using H2O2 was evaluated. Photocatalytic treatment was then tested isolated, in sequence and combinated with the oxidation processo using H2O2. Finally, oxidation with H2O2 and anaerobic digestion were combinated and evaluated. The PHWW showed high organic load, alkaline pH and high concentrations of nutrients (nitrogen and phosphorus). The presence of CNC as pyrazines, δ-valerolactam, caprolactam and butyrolactam was also verified. The application of the oxidative process using H2O2 showed positive effects mainly for color removal, which reached 93.8%. The maximum efficiency of COD removal was 15.3%. Reduction in CNC concentrations was also observed . The efficiency of the advanced oxidation process (by combining photocatalysis and H2O2) was greater than that obtained when these processes were applied separately. The application of the combined process presented color and COD removal efficiencies similar to those obtained when the processes were applied in sequence, allowing reaction time savings. Finally, the anaerobic digestion of pre-treated (with H2O2) PHWW showed a greater CH4 production and higher organic matter removal, compared to anaerobic digestion of in natura PHWW. Thus it is possible to conclude that the utlization of advanced oxidation processes or the combination of oxidation with H2O2 and anaerobic digestion are promising alternatives for the treatment of PHWW.

[pt] Com aumento da preocupação político-ambiental, torna-se imperativo desenvolver processos eficientes em termos econômicos e energéticos para a produção sustentável de combustíveis e produtos químicos. A liquefação hidrotérmica (HTL) é um processo para a transformação de materiais orgânicos, tais como bio-resíduos ou biomassa, em óleo bruto, em temperaturas usualmente inferiores a 400 graus Celsius sob altas pressões na presença de água, e, dependendo do processo, de um catalisador. Nesse contexto, é importante entender o comportamento de degradação térmica do material em atmosfera inerte, no sentido de se investigar a possibilidade de quebra das cadeias poliméricas inicias em moléculas menores, que, mediante pressão, poderão ser convertidas em novos produtos. Assim sendo, os objetivos do presente trabalho estão associados ao estudo termogravimétrico (TG) da degradação térmica da fibra do coco verde na presença de ferrita de cobalto (Fe2CoO4), utilizada no intuito de gerar um efeito catalítico, acelerando a degradação térmica das estruturas poliméricas presentes, e, que possa ser usada posteriormente em uma rota HTL. Os catalisadores foram produzidos a 1000 graus Celsius em diferentes tempos de calcinação (3h, 6h e 9h), sendo, nas misturas com a fibra, a fração mássica de óxido igual a 50 por cento. As amostras de interesse para a pesquisa foram caracterizadas mediante diferentes técnicas, tais como, a microscopia eletrônica de varredura, para o estudo da morfologia e composição elementar, difração de raios X, para a quantificação das fases presentes nas amostras de ferrita, e espectroscopia de infravermelho, visando à identificação das principais ligações químicas nas fibras, tanto antes quanto durante o tratamento térmico. Dentre todos os ensaios de TG realizados, os experimentos com o catalisador calcinado durante 9h homogeneizado com gral de ágata foi o que mostrou uma melhor resposta com relação à degradação térmica das fibras. Os resultados sugerem ainda que, tanto o tempo de calcinação, quanto a natureza do processo de mistura apresentam efeitos significativos sobre a cinética de degradação. / [en] With increasing political-environmental concern, it becomes imperative to develop efficient processes in economic and energy terms for the sustainable production of fuels and chemical products. Hydrothermal liquefaction (HTL) is a process for the transformation of organic materials such as bio-waste or biomass into crude oil at temperatures usually below 400 degrees Celsius under high pressures in the presence of water and, depending on the process, of a catalyst. In this context, it is important to understand the behavior of thermal degradation of the material under inert atmosphere, in order to investigate the possibility of breaking the initial polymer chains into smaller molecules, which, under pressure, can be converted into new products. The objectives of the present work are associated to the thermogravimetric study (TG) in the thermal degradation of the green coconut fiber in the presence of a cobalt ferrite (Fe2CoO4), used to generate a catalytic effect, accelerating the thermal degradation of the polymeric structures present, and which can be used later on an HTL route. The catalysts were produced at 1000 degrees Celsius at different calcination times (3h, 6h and 9h) and in the fiber mixtures, the oxide mass fraction was equal to 50 percent. The samples of interest for the research were characterized by different techniques, such as scanning electron microscopy, for the study of the morphology and elemental composition, X-ray diffraction, for the quantification of the phases present in the ferrite samples, and spectroscopy of Infrared, in order to identify the main chemical bonds in the fibers, both before and during the heat treatment. Among all the TG assays performed, the experiments with the catalyst calcined for 9h homogenized with mortar and pestle showed the best to the thermal degradation of the fibers. The results further suggest that both the calcination time and the nature of the blending process have significant effects on the degradation kinetics.