O presente trabalho trata das estratégias de agregação de tráfego IP nas redes óticas WDM. Utilizar todo um comprimento de onda para transportar um único fluxo de dados numa rede WDM é ineficiente. O problema conhecido como agregação de tráfego consiste na multiplexação de distintos fluxos de tráfego em um mesmo comprimento de onda sobre um caminho ótico. A alocação de múltiplos fluxos de tráfego em comprimentos de onda é realizada por protocolos de controle de admissão, roteamento e designação de comprimento de onda (RWA) e algoritmos de agregação de tráfego. Neste trabalho é simulado o comportamento dinâmico e elástico do tráfego IP diretamente sobre a camada ótica. Com base nos resultados das simulações determinam-se os efeitos da granularidade dos fluxos IP nos parâmetros de desempenho da rede. As topologias utilizadas durante as simulações são das redes NSFNET e Kyatera. É estabelecida também uma correlação entre a granularidade dos fluxos de tráfego e os parâmetros de desempenho da rede. / The present work covers the IP traffic grooming strategies in optical WDM networks. Using an entire wavelength to transport an individual traffic flow in a WDM network is inefficient. The problem known as traffic grooming consists in the multiplexing of different traffic flows in a single wavelength within a lightpath. The allocation of multiple traffic flows is performed by routing and wavelength assignment (RWA) and traffic grooming algorithms. In this work it is simulated the dynamic and elastic behavior of IP traffic directly on top of the optical layer. Based on the simulation results the effects of the IP traffic flow granularity on the network performance parameters are determined. The simulated topologies are the NSFNET and Kyatera. It is also established the correlation between the traffic flow granularity and the network performance parameters.

Centralized light source (CLS) at the central office is an attractive solution for low-cost implementation of WDM-PON, as it eliminates the need of wavelength-specific transmitters and wavelength management at the optical network units (ONU). CLS can be realized by either a carrier-distributed scheme or a remodulation scheme. In both schemes, however, the upstream signal is susceptible to the interferometric crosstalk induced by the beating between the upstream signal and the back-reflected light due to the intrinsic Rayleigh Backscattering (RB), both of which are of the same wavelength. We propose and demonstrate a simple and novel scheme to suppress the RB noise in the carrier-distributed WDM-PON. Differential phase-shift keying (DPSK) is used as the upstream modulation format and the destructive port of the delay-interferometer (DI) is employed to demodulate the upstream DPSK signal. As the spectrum of RB towards the OLT is narrow due to the very narrow spectrum of the distributed carrier, the RB noise can be considerably rejected by the notch filter-like destructive port of the DI at the OLT, which is used simultaneously to demodulate the upstream DPSK signal. The scheme can also be extended to the application in the remodulation-based WDM-PON, as long as the downstream signal has a narrow spectrum (i.e. via reducing downstream modulation depth). A unique feature of the DPSK signal with reduced modulation depth (RMD-DPSK) is that it can be demodulated by DI's destructive port without extinction ratio (ER) degradation, whereas the demodulated signal from DI's destructive port has a very low ER and can be used as the source for upstream remodulation. We also proposed a novel offset-Manchester coding to suppress Rayleigh noise in electrical domain via a postdetection high-pass filter. / Foreseeing the rapidly growing demand for multimedia services and the trend of service convergence, the penetration of optical fiber in access network is an ultimate solution to break the last-mile bottleneck imposed by the 100-year-old copper network. One of the most promising solutions to realize optical access is the passive optical network (PON), in which the network infrastructure is shared by many subscribers and has no active elements between the central office and the customer. Thus a PON requires neither electrical power nor active management, leading to effective reduction in operational expenses. Time-division-multiplexed passive optical networks (TDM-PONs) such as Ethernet PON (EPON) and Gigabit PON (GPON) are being widely deployed in current fiber-based access networks for providing broadband access, offering triple-play services including video, data and voice. In the near future, wavelength-division-multiplexed passive optical network (WDM-PON) can be the enabler of the next-generation optical broadband access that requires large dedicated and symmetric bandwidth, data privacy, and upgrade flexibility. TDM-PONs also can benefit from WDM technologies for capacity upgrade. / With more diverse multimedia and data services available for broadband access, the access network has to be flexible enough to cope with various data or video delivery such as broadcast/multicast services, in addition to the point-to-point traffic. Multicast is more attractive, compared to broadcast, as it allows selective control of the connection for each subscriber individually. Multicast can be easily realized in TDM-PONs as it employs power-splitting at the remote node (RN). However, it is more challenging in WDM-PONs, due to the dedicated connection between the optical line terminal (OLT) and each ONU. Many studies have been carried out to solve this problem. The prior schemes either need relatively complicated multicast control and/or cannot support future proof 10-Gb/s symmetric point-to-point (PtP) transmission. We proposed a novel multicast control scheme for a WDM-PON with 10-Gb/s symmetric bit rate. The multicast data encoded in DPSK format is superimposed onto all PtP channels modulated in inverse return-to-zero format. With an athermal Dr being used at the ONU to demodulate the DPSK signal, the multicast data can be effectively disabled by slight detuning the laser wavelength at OLT, which has negligible effect on the PtP data. The proposed scheme differs from all the previous schemes in that, the multicast control is realized via the inherent wavelength management of WDM systems, rather than via any other additional adjustment such as ER, synchronization, and polarization. v / Xu, Jing. / Adviser: Lian-Kuan Chen. / Source: Dissertation Abstracts International, Volume: 73-06, Section: B, page: . / Thesis (Ph.D.)--Chinese University of Hong Kong, 2011. / Includes bibliographical references. / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. [Ann Arbor, MI] : ProQuest Information and Learning, [201-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstract also in Chinese.

In this thesis, a fully millimetre-wave (mm-wave) generation and transmission system is proposed for futuristic communications. Significant challenges have been dealt with regarding the proposed system, including designing the mm-wave generation and transmission technique, and its application in cellular networks. These challenges are presented through five main contributions and validated via Optiwave Design Software and MATLAB simulation tools. Firstly, three novel photonic generation methods are proposed and designed based on the characteristics of Brillouin fibre laser and the Stimulated Brillouin Scattering (SBS) effects with phase modulation. The mm-wave carriers are successfully generated with a tuning capability from 5 to 90 GHz. Also, these carriers are with good Signal to Noise Ratio (SNR) up to 51 dB, and low noise signal power of about -40 dBm. The impact of these methods is obtaining stable mm-waves appropriate for Radio over Fibre (RoF) transmission systems in 5G optical networks. Secondly, a full-duplex RoF system with the generation of a 64 GHz mm-wave is proposed. Successful transmission of the mm-wave over a fibre link is achieved for up to 100 km of fibre with a data rate of 5 Gbits/s. The main impact of this system is cost reduction and performance improvement by simplifying mm-wave generation and transmission over fibre. Also, it ensures a useful communication link for small cell networks. Thirdly, a hybrid Fibre/Free-space optical (FSO) system for the generation and transmission of 64 GHz mm-wave is proposed. This optical system provides a low latency communication link and overcomes mm-wave high path losses. A successful mm-wave transmission is achieved over a 10 km fibre length, and 2 km FSO link length with a good Bit Error Rate (BER) of about 1.5×10-13 and a data rate of 10 Gbits/s. This system increases the network coverage area by transmitting the mm-wave over the FSO link to the areas with natural obstacles the laying of fibre cables impossible. Also, it can be used as an effective solution under emergency disaster conditions. Fourthly, a comprehensive study of the wireless propagation performance for different mm-wave bands (28, 60, and 73 GHz) as cellular networks is investigated and compared with the 2.4 GHz Ultra-High Frequency band (UHF). A map-based scenario is proposed for the deployment of Base Stations (BSs) within the Brunel University London Campus map to consider real blockage effects. This investigation involved specifying which mm-wave spectrum can enhance the futuristic cellular networks, by evaluating the coverage and rate trends. Comparative results show that the 73 GHz bands can achieve the higher rate with good coverage and the lowest interference effects than the other mm-wave bands. Finally, a simplified path loss model is proposed to estimate precisely the 28 GHz mm-wave performance, which is considered a key component in 5G networks in outdoor applications. The proposed path loss model captures the diffraction and specular reflection impacts on mm-wave wireless propagation.

Besides colorless ONUs, we investigate potentially low cost, high speed vertical-cavity-surface-emitting lasers (VCSELs) for use in future access networks. VCSELs are attractive because they may meet the stringent size, power dissipation and cost constraints of access network components. We carry out experiments to demonstrate that up to 20 Gb/s direct modulation of long wavelength VCSEL is possible and evaluate their performance as high-speed transceivers. / In order to reduce the complexity and costs of ONU transceiver, we propose a scheme based on a nonreciprocal optical modulator and a linear loop mirror for receiving downstream and sending upstream data We show that the nonreciprocity of traveling wave electrodes can selectively impress signal modulation onto the reflected upstream signals only. Monolithic integrated transceivers may thus remodulate downstream signals for upstream data transmission without needing integrated optical circulators. The proposed ONU is thus compatible with monolithic integration. / In this thesis, we describe our research on photonic devices and subsystems for future access networks. Since optical network units (ONUs) are the most cost-sensitive parts, we first investigate the use of advanced modulation format in colorless ONU structure. We implement a scheme which uses dark return-to-zero (DRZ) for downstream transmission and remodulation of it using a differential-phase-shift-keying (DPSK) for upstream both at 10 Gb/s. We also experimentally demonstrate silicon microring based optical frequency discriminators for use in demodulating DPSK and differential-quadrature-phase-shift-keying (DQPSK) signals. We show that the scheme is robust to variations in bit-rates in contrast with conventional Mach-Zehnder delay interferometer scheme. / Internet traffic has undergone tremendous growth in the past decades and has already penetrated into the daily lives of the general population. Demand for new high bandwidth services is beginning to drive the deployment of optical fiber-based access networks to solve the so-called last mile bottleneck around the world. Passive optical networks (PON) are attractive because there are no active components in the transmission line, thus reducing operational and deployment costs. Time-division-multiplexing (TDM) used in currently deployed PON, in which the bandwidth is shared among the users by time domain multiplexing, does not fully utilize the bandwidth potential of optical fibers and will not be able to satisfy the bandwidth demand in access networks in the near future. Among the advanced multiplexing techniques, wavelength-division-multiplexing (WDM) PON is a good candidate technology for providing sustained bit-rates beyond 10 Gb/s in access networks. However, reduction of costs in WDM PON remains a key challenge for their practical deployment. / Wired and wireless hybrid optical access networks are also investigated. Radio-over-fiber is one low-cost approach to deliver broadband wireless services, in which radio signals at the carrier frequency are delivered over optical networks from a central office to remote antenna base stations. Generation of high frequency carrier and radio frequency fading are the main research challenges. We propose and demonstrate frequency upconversion based on frequency doubling and quadrupling. Novel wired and wireless hybrid subsystems that mitigate millimeter-wave signal distortion are also demonstrated. / Xu, Lin. / Adviser: H. K. Tsang. / Source: Dissertation Abstracts International, Volume: 72-04, Section: B, page: . / Thesis (Ph.D.)--Chinese University of Hong Kong, 2010. / Includes bibliographical references. / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. Ann Arbor, MI : ProQuest Information and Learning Company, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstract also in Chinese.

O presente trabalho trata das estratégias de agregação de tráfego IP nas redes óticas WDM. Utilizar todo um comprimento de onda para transportar um único fluxo de dados numa rede WDM é ineficiente. O problema conhecido como agregação de tráfego consiste na multiplexação de distintos fluxos de tráfego em um mesmo comprimento de onda sobre um caminho ótico. A alocação de múltiplos fluxos de tráfego em comprimentos de onda é realizada por protocolos de controle de admissão, roteamento e designação de comprimento de onda (RWA) e algoritmos de agregação de tráfego. Neste trabalho é simulado o comportamento dinâmico e elástico do tráfego IP diretamente sobre a camada ótica. Com base nos resultados das simulações determinam-se os efeitos da granularidade dos fluxos IP nos parâmetros de desempenho da rede. As topologias utilizadas durante as simulações são das redes NSFNET e Kyatera. É estabelecida também uma correlação entre a granularidade dos fluxos de tráfego e os parâmetros de desempenho da rede. / The present work covers the IP traffic grooming strategies in optical WDM networks. Using an entire wavelength to transport an individual traffic flow in a WDM network is inefficient. The problem known as traffic grooming consists in the multiplexing of different traffic flows in a single wavelength within a lightpath. The allocation of multiple traffic flows is performed by routing and wavelength assignment (RWA) and traffic grooming algorithms. In this work it is simulated the dynamic and elastic behavior of IP traffic directly on top of the optical layer. Based on the simulation results the effects of the IP traffic flow granularity on the network performance parameters are determined. The simulated topologies are the NSFNET and Kyatera. It is also established the correlation between the traffic flow granularity and the network performance parameters.

[pt] A indústria das comunicações tem passado nos últimos anos, mundialmente, por profundas transformações. A Internet é a responsável pela maior destas transformações. Com o advento da Internet, existe a necessidade de uma banda de transmissão maior para o tráfego de dados. Para resolver esse problema, surgiu o conceito de redes ópticas e a multiplexação no domínio do comprimento de onda. Entretanto, isso criou um outro problema: o roteamento dos pacotes. A maior parte das redes de comunicação hoje em dia, ainda possui muitos sinais eletrônicos, o que significa que os sinais ópticos precisam ser convertidos em elétricos para serem ampliados, regenerados ou roteados e, depois, reconvertidos para ópticos. Isso acaba gerando atrasos na transmissão dos sinais e um gargalo nas redes ópticas. Para minimizar este problema, vários algoritmos foram criados. Apegando-se a tais fatos, este estudo explora o tema para implementar um algoritmo de enumeração recursiva, que tem como objetivo alocação de comprimentos em redes ópticas, visando minimizar o custo total de transmissão. Esse algoritmo foi testado e comparado com o algoritmo de programação linear, que fornece a solução ótima. / [en] The communication industry was passing in lastest years by great transformations in world. Internet is the mainly responsable for that, because there is the necessity of a large band to data transmission. The optical networks concept and wavelength division multiplexing technology were arised in order to solve this problem. However, this created another problem: the packet routing. The major part of communications networks still has electronics signals. This means that the optical signals have to be converted into electrical signals to be amplified, regenerated and routed and later recovered into optical. This implies in a delay on the data transmission and creates a bottleneck in the optical networks. Some algorithms have been created to minimize this problem. This dissertation has tried to develop an algorithm to solve RWA (routing and wavelength assignment) problems, aiming at the minimum total cost to transmitt datas. This algorithm was tested and compared with the linear program algorithm that gives the optimal solution to RWA problem.

Las redes de transporte se mueven hacia un modelo de redes formadas por routers IP/MPLS (Internet Protocol/Multiprotocol Laebel Switching) de altas prestaciones interconectadas a través redes troncales inteligentes. Actualmente la tecnología ATM está ampliamente desarrollada en dichas redes troncales que utilizan los protocolos PNNI (Private Network- Network Interface) como plano de control. En cambio la interoperabilidad entre redes IP/MPLS a través de redes PNNI-ATM es todavía un aspecto en proceso de estudio. Por otro lado, la tendencia futura de Internet es ir hacia redes troncales completamente ópticas con capacidad automática de conmutación para permitir un mejor tratamiento del tráfico solicitado. Debido al esfuerzo realizado por los organismos de estandarización sobre redes ópticas, se ha definido un primer modelo de red llamado ASON (Automatic Switched Optical Network). Mientras las redes actuales basadas en SDH (Synchronous Digital Hierarchy) ofrecen sólo capacidad de transporte, la futura ASON permitirá el establecimiento y la liberación de canales ópticos de forma automática. Un aspecto clave para conseguir esta funcionalidad es la definición de un plano de control óptico que será el responsable de realizar las funciones de señalización y encaminamiento.Diferentes estudios han sido realizados para conseguir interoperabilidad entre redes con tecnología IP/MPLS y ATM basados esencialmente en la distribución de información de señalización MPLS a través de una red troncal ATM. Una de las soluciones planteadas se basa en la utilización sobre cada uno de los conmutadores ATM, un dispositivo capaz de procesar información MPLS, llamado LSR (Label Switched Router). Otra, en cambio, propone el establecimiento de un camino MPLS, llamado LSP (Label Switched Path), encapsulado dentro de un camino ATM o VPC (Virtual Path Connection). Ambas soluciones presentan el inconveniente de utilizar un tiempo de establecimiento demasiado elevado.Respecto al plano de control para ASON, decir que una de las opciones propuestas es la de utilizar el GMPLS (Generalizad MPLS) que es una extensión del modelo MPLS con ingeniería de tráfico. Sin embargo, recientemente se ha iniciado un debate en lo foros de estandarización sobre la posibilidad de utilizar el PNNI como plano de control en ASON. Los argumentos que justifican esta opción son que el PNNI, después de unas apropiadas modificaciones, puede ser adecuado para ASON y lleva años funcionando en muchas de las actuales redes de transporte.Esta tesis está basada en el estudio de los dos casos mencionados anteriormente. El primero caso es el de dos redes IP/MPLS conectadas a través de una red troncal ATM la cual utiliza el PNNI como plano de control. En este contexto, el objetivo principal será el de definir un mecanismo rápido de establecimiento de la conexión que proporcione los parámetros requeridos de calidad deservicio entre dos nodos pertenecientes a cada una de las redes IP/MPLS. Para conseguirlo se realizarán las modificaciones pertinentes en el PNNI y se añadirán nuevos elementos de señalización.El segundo caso consiste en interconectar dos redes IP/MPLS a través de una red tronca l´óptica. En primer lugar se adaptará el PNNI para conseguir un protocolo de encaminamiento para ASON con el fin de proporcionar un establecimiento rápido de la conexión en un entorno IP/MPLS-ASON. Finalmente, se definirá un plano de control, llamado O-PNNI (Optical PNNI) basado en la adaptación total del ATM PNNI a redes ASON. Esta tesis finaliza con un análisis de las ventajas y desventajas de los modelos GMPLS y O-PNNI como planos de control en ASON.

L'evolució de les xarxes publiques de transport de dades destaca per el continu augment de la demanda de tràfic a la que estan sotmeses. La causa és la imparable popularització d'Internet i del seu ús per a tot tipus d'aplicacions. Les xarxes de commutació de ràfegues òptiques (OBS: Optical Bursts Switching) són una solució extraordinàriament prometedora per la pròxima generació de xarxes, tant per la flexibilitat que ofereixen com per el seu alt rendiment fruit de l'explotació de la multiplexació estadística en el domini òptic.Aquesta tesi presenta l'anàlisi, modelització i avaluació de les xarxes de commutació de ràfegues òptiques basades en l'emulació del temps de compensació (emulated offset time: E-OBS). El concepte d'E-OBS defineix una arquitectura de xarxa OBS per al transportar i commutar ràfegues òptiques en una xarxa troncal en la que, al contrari de l'arquitectura convencional (C-OBS) en la que el temps de compensació s'introdueix des dels nodes d'accés, el temps de compensació s'introdueix en cadascun dels nodes de la xarxa per mitjà d'un retardador de fibra addicional. L'arquitectura E-OBS permet superar algunes de les desavantatges inherents a arquitectures C-OBS, però la seva gran virtut és la compatibilitat amb les xarxes de commutació de circuits òptics (OCS: Optical Circuit Switching) actuals i les futures xarxes de commutació de paquets òptics (OPS: Optical Packet Switching), de manera que les xarxes OBS basades en una arquitectura E-OBS) poden facilitat enormement la transició de unes a les altres.A ala vista dels principals requeriments de disseny de les xarxes OBS, que són la resolució de contencions en el domini òptic, la provisió de qualitat de servei (QoS) i l'òptim encaminament de les ràfegues per tal de minimitzar la congestió de la xarxa, . en aquesta tesi es proposa un disseny de l'arquitectura E-OBS basada en (i) un mètode viable per a la provisió del temps de compensació, (ii) una qualitat alta global de servei, i (iii) un mecanisme d'encaminament que minimitzi congestió de xarxa.- La primera part d'aquesta tesi proporciona la informació documental necessària per al disseny d'E-OBS.- La segona part se centra en l'estudi de la funcionalitat i viabilitat de l'arquitectura E-OBS. S'introdueixen els principis d'operació d'E-OBS i s'identifiquen els principals esculls que presenten les arquitectures C-OBS i que deixen de ser-ho en una arquitectura E-OBS. Alguns d'aquests esculls són la dificultat d'utilitzar un algorisme d'encaminament amb rutes alternatives, la complexitat dels algoritmes de reserva de recursos i la seva falta d'equitat, la complexitat en la provisió de la QoS, etc. En aquesta segona part es constata que l'arquitectura E-OBS redueix la complexitat dels de reserva de recursos i es verifica la viabilitat d'operació i de funcionament de la provisió del tremps de compensació en aquesta arquitectura a partir de figures de comportament obtingudes amb retardadors de fibra comercialment disponibles.- La tercera part encara el problema de la provisió de la QoS. Primer s'hi revisen els conceptes bàsics de QoS així com els mecanismes de tractament de la QoS per a xarxes OBS fent-ne una comparació qualitativa i de rendiment de tots ells. Com a resultat s'obté que el mecanisme que presenta un millor comportament és el d'avortament de la transmissió de les ràfegues de més baixa prioritat quan aquestes col·lisionen amb una de prioritat més alta (es l'anomenat Burst Preemption mechanism), el qual en alguns casos presenta un problema de senyalització innecessària. Aquesta tercera part es conclou amb la proposta d'un mecanisme de finestra a afegir al esquema de Burst Preemption que només funciona sobre una arquitectura E-OBS i que soluciona aquest problema.- En la quarta part s'afronta el problema de l'encaminament en xarxes OBS. S'estudia el comportament dels algoritmes d'encaminament adaptatius, els aïllats amb rutes alternatives i els multicamí distribuïts, sobre xarxes E-OBS. A la vista dels resultats no massa satisfactoris que s'obtenen, es planteja una solució alternativa que es basa en model d'optimització no lineal. Es formulen i resolen dos models d'optimització per als algoritmes encaminament de font multicamí que redueixen notablement la congestió en les xarxes OBS.Finalment, aquesta tesi conclou que l'arquitectura E-OBS és factible, que és més eficient que la C-OBS, que proveeix eficaçment QoS, i que és capaç d'operar amb diverses estratègies d'encaminament i de reduir eficaçment la congestió de xarxa. / The fact that the Internet is a packet-based connection-less network is the main driver to develop a data-centric transport network. In this context, the optical burst switching (OBS) technology is considered as a promising solution for reducing the gap between transmission and switching speeds in future networks.This thesis presents the analysis, modelling, and evaluation of the OBS network with Emulated offset-time provisioning (E-OBS). E-OBS defines an OBS network architecture to transport and switch optical data bursts in a core network. On the contrary to a conventional offset-time provisioning OBS (C-OBS) architecture, where a transmission offset time is introduced in the edge node, in an E-OBS network the offset time is provided in the core node by means of an additional fibre delay element. The architecture is motivated by several drawbacks inherent to C-OBS architectures. It should be pointed out that the E-OBS has not been studied intensively in the literature and this concept has been considered rather occasionally.Due to the limitations in optical processing and queuing, OBS networks need a special treatment so that they could solve problems typical of data-centric networks. Contention resolution in optical domain together with quality of service (QoS) provisioning for quality demanding services are, among other things, the main designing issues when developing OBS networks. Another important aspect is routing problem, which concerns effective balancing of traffic load so that to reduce burst congestion at overloaded links. Accounting for these requirements, the design objectives for the E-OBS architecture are (i) feasibility of offset-time provisioning, (ii) an overall high quality of service, and (iii) reduction of network congestion. These objectives are achieved by combining selected concepts and strategies, together with appropriate system design as well as network traffic engineering.The contributions in this thesis can be summarized as follows.- At the beginning, we introduce the principles of E-OBS operation and we demonstrate that C-OBS possesses many drawbacks that can be easily avoided in E-OBS. Some of the discussed issues are the problem of unfairness in resources reservation, difficulty with alternative routing, complexity of resources reservation algorithms, efficiency of burst scheduling, and complexity in QoS provisioning. The feasibility of E-OBS operation is investigated as well; in this context, the impact of congestion in control plane on OBS operation is studied. As a result, we confirm the feasibility of E-OBS operation with commercially available fibre delay elements.- Then, we provide both qualitative and quantitative comparison of the selected, most addressed in the literature, QoS mechanisms. As an outcome a burst preemption mechanism, which is characterized by the highest overall performance, is qualified for operating in E-OBS. Since the preemptive mechanism may produce the overbooking of resources in an OBS network we address this issue as well. We propose the preemption window mechanism to solve the problem. An analytical model of the mechanism legitimates correctness of our solution.- Finally, we concern with a routing problem - our routing objective is to help the contention resolution algorithms in the reduction of burst losses. We propose and evaluate two isolated alternative routing algorithms designed for labelled E-OBS networks. Then we study multi-path source routing and we use network optimization theory to improve it. The presented formulae for partial derivatives, to be used in a non-linear optimization problem, are straightforward and very fast to compute. It makes the proposed non-linear optimization method a viable alternative for linear programming formulations based on piecewise linear approximations.Concluding, E-OBS is shown to be a feasible OBS network architecture of profitable functionality, to support efficiently the QoS provisioning, and to be able to operate with different routing strategies and effectively reduce the network congestion.

El estudio e investigación en el campo de las redes ópticas de acceso han sido fomentadas en años recientes debido a la continua migración de Servicios multimedia que son ofrecidos a través de Internet. Aunque los dispositivos utilizados para implementar Fiber-to-the-Home (fibra a casa), que reemplazan las soluciones tradicionales basadas en cable de cobre, están basadas aún en micro-óptica, se puede prever una evolución hacia integración fotónica. Todavía queda la pregunta acerca de los diseños necesarios para este paso importante de integración, que debe ser optimizado en términos del desempeño de transmisión, eficiencia energética y costo con el fin de lograr todos los requerimientos de las redes fotónicas de siguiente generación. Como elemento más crítico en las redes de acceso ópticas es el equipo en los clientes, este trabajo se centra en éste. Los temes cubiertos abarcan una gama amplia e incluyen: el reciclado de longitudes de onda para transmisión de datos en full-dúplex a través de una sola frecuencia óptica; la generación de formatos de modulación avanzados con moduladores semiconductores de bajo costo y factor pequeño de integración; soporte de amplificación óptica a través de técnicas de sembrado y el soporte de funcionalidades de capes superiores en la capa física. Después de la prueba principal de las técnicas propuestas, se resaltan los beneficios, impedimentos y caminos de reemplazo hacia sistemas fotónicos multifuncionales a través de casos de estudio. Por su parte, los diseños más representativos se profundizan más sobre todo por su posibilidad de ser integrados fotónicamente. / Optical access technology has experienced a boost in the last years, thanks to the continuously migrating multimedia services that are offered over the internet. Though the devices used for deploying Fiber-to-the-Home instead of traditional copper-based solutions are still based on micro-optics, an evolution towards photonic integration can be foreseen. What remains is the question about the exact designs for this important step of integration, which should be optimized in terms of transmission performance, energy efficiency and cost to address all requirements of next-generation photonic networks. As the most critical element in optical access, the customer premises equipment is in primary focus of this discussion. The covered topics span over a wide range and include wavelength recycling for full-duplex data transmission on a single optical frequency, the generation of advanced modulation formats with low-cost semiconductor modulators with small form factor, support for optical amplification by means of seeding techniques and the support of higher layer functionality at the physical layer. Next to the principal proof of the proposed techniques, the benefits, impediments and upgrade paths towards multifunctional photonic systems are highlighted in different case studies, while the most representative designs are further discussed in their capability of being photonically integrated.

In recent years, the ever-increasing environmental friendliness concern has made energy efficiency in telecom networks as an important theme in their operations. Meanwhile, mission-critical (MC) services and systems (such as healthcare, police, and firefighting) have been acquiring special attention from telecom designers and operators. The currently deployed MC network technologies are indigent in terms of bandwidth capacity, and thus they are not able to support the emerging MC multimedia applications. Therefore in this thesis, we first explore the possibility of provisioning the MC services over the integration of fiber-wireless (FiWi) technologies, which has been considered as a promising candidate for the deployment of high-speed and mobile broadband access networks. We then investigate the energy efficiency problem in the FiWi integration, which consists of WiMAX in the wireless plane, and of Ethernet Passive Optical Network (EPON) - the most popular variant of the next-generation PON (NG-PON) technology, in the optical plane. In WiMAX, the energy saving protocol has been extensively investigated and standardized. Conversely, it has been recently studied in NG-PON, which currently consumes the least power among all the high-speed access networks. However, NG-PON has notably matured in the past few years and is envisioned to massively evolve in the near future. This trend will increase the power requirements of NG-PON and make it no longer coveted. Therefore we address the energy efficiency problem in NG-PON. For each of our contributions, we conduct extensive simulations to demonstrate the effectiveness and advantages of the proposed solutions.