This thesis focuses on the comprehensive study of controlling a customized Active Magnetic Bearing (AMB) installed on Bently Nevada’s RK4 rotor kit in Cal Poly’s Vibrations and Rotordynamics Lab. The AMB was uniquely designed and manufactured by a Cal Poly senior project team to fit Bently’s rotor kit and the results of this research are distinctive to the custom system. To achieve practical functionality of the AMB system, we designed a controller a Virtual Instrument (VI) using the National Instrument software, LabVIEW. From the experimental study, we calibrated the programming to find unknown parameters of the AMB system and validated the design using a well-established industrial rotordyanmics software, Bentley Nevada System 1. The development of the control programming consists of theoretical analysis (MATLAB/ Simulink) and simulation validation (MSC ADAMS View). Both linear and non-linear models were implemented in MATLAB and Simulink to effectively tune a Proportional-Integral-Derivative (PID) control developed for various AMB models. To validate the theoretical results, we compared them to results from a co-simulation using MSC Adams VIEW, a multi-body dynamics simulation, and Simulink. From experimental trial and error at a shaft rotational speed of 2800 rpm, a 16% decrease in shaft orbit was achieved. These results demonstrate the practicality of the control program and custom AMB rotor kit that can be used for further research.

A Thesis Submitted to the School of Graduate Studies in Partial Fulfillment of the Requirements for the Degree of Master of Applied Science in Mechanical Engineering / In the wake of the rising global demand for more electric transportation, aerospace electrification is becoming a highly active research area as commercial fully electric aircrafts are becoming a reality. The transportation electrification industry is challenged to develop powerful, safe, and compact-sized machines that can replace fossil fuel powered engines in aircrafts. Axial Flux Permanent Magnets (AFPM) machines are currently being intensively developed as a great candidate for this purpose due to their inherently higher power density compared to other machine electric machines topologies. The efforts of further increasing AFPM machines power density add more thermal challenges as intensive cooling is required at a relatively small machine package to avoid machine failure. One of the most concerning failure modes in these machines is power output reduction due to overheating of the rotor-mounted permanent magnets or even complete failure due to irreversible demagnetization. This research discusses the design process of an integrated rotor air cooling system for a 100 kW AFPM machine designed for an electric aircraft propulsion system. The embedded cooling system allows the rotor to be self-cooled at a sufficient cooling rate while minimizing the impact on machine efficiency due to windage power losses. The presented design process includes several stages of cooling enhancement including the addition and fine-tuning of rotor fan blades and rotor vents design. These enhancements are done by studying the air flow over the rotor surfaces in conjunction with heat transfer through Conjugate Heat Transfer (CHT) Computational Fluid Dynamics (CFD) analyses. In an initial study, different rotors with different combinations of rotor cooling features are studied and their thermal performance is compared. The results show that using rotor embedded fan blades in throughflow ventilated rotor geometry offers the best performance balance, achieving sufficient rotor cooling rate within a reasonable increase of windage power loss. A parametric study is performed to improve the rotor blade geometry for a higher ratio of heat transfer to windage losses. Another study is performed where the rotor and the enclosure geometries are fine-tuned simultaneously to reduce the negative effect on rotor heat transfer imposed by the enclosure. The final geometry of the rotor enclosure assembly is generated based on the research results and the design is integrated into the final machine prototype to be tested. / Thesis / Master of Applied Science (MASc) / Axial-flux permanent magnets (AFPM) machines are gaining the transportation electrification industy attention as a greener alternative to combustion engines in aircraft propulsion systems due to their high power and torque density. The intense endeavors of the current research to further improve AFPM machines power densities brings thermal design challenges to ensure the safe operation of the machine. Rotor permanent magnets failure due to demagnetization as a result of overheating can impose a great risk to the machine operation and safety. Accordingly, special attention should be paid to rotor thermal management. This research discusses the design process of an integrated rotor air cooling system for an AFPM machine designed for an electric aircraft. The machine mechanical and thermal design parameters are used to set an initial rotor design with different rotor cooling features based on literature findings. Rotor fan blades and air vents are selected as the main rotor cooling features for the design. Several design iterations are then made to fine-tune the rotor geometry targeting low operating temperature of the permanent magnets at a low cost of windage losses. The thermal performance of the different designs is assessed and compared to each other using conjugate heat transfer (CHT) computational fluid dynamics (CFD) analyses. Safe operating temperature of the magnets is achieved at an acceptable windage losses value with the final design, and it is selected for prototyping.

No description available.

No description available.

No description available.

No description available.

No description available.

No description available.

No description available.

No description available.