No description available.

Elimination or reduction of auxiliary oxygen use in Pulse Detonation Engines (PDEs) is necessary if the technology is to compete with existing Ramjet systems. This thesis investigated a Transient Plasma Ignition (TPI) system and found that the technology can at least reduce and may be able to completely remove the auxiliary oxygen requirement of current PDE systems. TPI was tested and compared with a traditional capacitive discharge spark plug system in a dynamic flow, ethylene/air mixture combustor. Ignition delay time, Deflagration-to-Detonation transition (DDT) distance and time, detonation wave speed and fire success rate performance were analyzed for various mass flow rates and stoichiometric ratios. A transient plasma dualelectrode concept was also employed and analyzed. Results show that TPI is more effective and reliable than the spark plug ignition with considerable improvements to DDT performance. The TPI dual-electrode concept was proven to be the most effective configuration with average reductions in DDT distance and time of 17% and 41% respectively when compared to the capacitive discharge spark plug system configuration.

Typescript (photocopy). / Digitized by Kansas Correctional Industries

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 1982. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / by Stephen Gregory Poulos. / M.S.

In this thesis Direct Numerical Simulation (DNS) is used to investigate the development of turbulent premixed flame kernels during the early stages of growth typical of the period following spark ignition. Two distinct aspects of this phase are considered: the interaction of the expanding kernel with a field of decaying turbulence, and the chemical and thermo-diffusive response of the flame for different fresh-gas compositions. In the first part of the study, three-dimensional, repeated simulations with single-step chemistry are used to generate ensemble statistics of global flame growth. The surface-conditioned mean fluid-velocity magnitude is found to vary significantly across different isosurfaces of the reaction progress variable, and this is shown to lead to a bias in the distribution of the Surface Density Function (SDF) around the developing flame. Two-dimensional simulations in an extended domain indicate that this effect translates into a similar directional bias in the Flame Surface Density (FSD) at later stages in the kernel development. Properties of the fresh gas turbulence decay are assessed from an independent, non-reacting simulation database. In the second part of this study, two-dimensional simulations with a detailed 68-step reaction mechanism are used to investigate the thermo-diffusive response of pure methane-air, and hydrogen-enriched methane-air flames. The changes in local and global behaviour due to the different laminar flame characteristics, and the response of the flames to strain and curvature are examined at different equivalence ratios and turbulence intensities. Mechanisms leading to flame quenching are discussed and the effect of mean flame curvature is assessed through comparison with an equivalent planar flame. The effects of hydrogen addition are found to be particularly pronounced in flame kernels due to the higher positive stretch rates and reduced thermo-diffusive stability of hydrogen-enriched flames.

Current stoichiometric spark-ignited engine technologies require costly catalytic converters for reductions in tailpipe emissions. Load control is achieved by using a throttle, which is a leading contributor to reductions in efficiency. Spark-ignited lean burn natural gas engines have been proven to be more efficient and emit fewer pollutants than their stoichiometric counterparts. Load reduction in these engines can be achieved by regulating the air/fuel ratio of the intake charge thereby reducing the efficiency penalties inherent to throttling. Partially stratified charge (PSC) can provide further reductions in emissions and improvements in efficiency by extending the lean limit of operation. PSC is achieved by the ignition of a small quantity of natural gas in the vicinity of the spark plug. This creates an easily ignitable mixture at the spark plug electrodes, thereby providing a high energy ignition source for the ultra-lean bulk charge. Stratified charge engine operation using direct injection (DI) has been proposed as a method of bridging the throttleless load reduction gap between idle and ultra-lean conditions. A previous study was conducted to determine if PSC can provide a high-energy ignition source in a direct injected stratified charge engine. Difficulties with igniting the PSC injections in an air-only bulk charge were encountered. This study focuses on a fundamental Schlieren image-based analysis of PSC combustion. Natural gas was injected through a modified spark plug located in an optically accessible combustion bomb. The relationships between PSC injection timing, fuel supply pressure and spark timing were investigated. Spark timing is defined as the duration between commanded start of injection and the time of spark. As the fuel supply pressure was increased, the minimum spark timing that lead to successful combustion also increased. The largest spark timing window that led to successful combustion was determined to be 80 ms wide at an injection fuel supply pressure of 300 psi. The amount of unburned natural gas increased with increasing spark timing. A cold flow study of the PSC injection system was also conducted. The PSC injection solenoid was found to have a consistent average injection delay of 1.95 ms. The slope of the linear response region of observed injection duration to commanded injection duration was 8.4. Due to plenum effects, the average observed injection duration of the entire PSC system was an order of magnitude longer than the commanded injection duration and was found to vary significantly with fuel supply pressure.

Current stoichiometric spark-ignited engine technologies require costly catalytic converters for reductions in tailpipe emissions. Load control is achieved by using a throttle, which is a leading contributor to reductions in efficiency. Spark-ignited lean burn natural gas engines have been proven to be more efficient and emit fewer pollutants than their stoichiometric counterparts. Load reduction in these engines can be achieved by regulating the air/fuel ratio of the intake charge thereby reducing the efficiency penalties inherent to throttling. Partially stratified charge (PSC) can provide further reductions in emissions and improvements in efficiency by extending the lean limit of operation. PSC is achieved by the ignition of a small quantity of natural gas in the vicinity of the spark plug. This creates an easily ignitable mixture at the spark plug electrodes, thereby providing a high energy ignition source for the ultra-lean bulk charge. Stratified charge engine operation using direct injection (DI) has been proposed as a method of bridging the throttleless load reduction gap between idle and ultra-lean conditions. A previous study was conducted to determine if PSC can provide a high-energy ignition source in a direct injected stratified charge engine. Difficulties with igniting the PSC injections in an air-only bulk charge were encountered. This study focuses on a fundamental Schlieren image-based analysis of PSC combustion. Natural gas was injected through a modified spark plug located in an optically accessible combustion bomb. The relationships between PSC injection timing, fuel supply pressure and spark timing were investigated. Spark timing is defined as the duration between commanded start of injection and the time of spark. As the fuel supply pressure was increased, the minimum spark timing that lead to successful combustion also increased. The largest spark timing window that led to successful combustion was determined to be 80 ms wide at an injection fuel supply pressure of 300 psi. The amount of unburned natural gas increased with increasing spark timing. A cold flow study of the PSC injection system was also conducted. The PSC injection solenoid was found to have a consistent average injection delay of 1.95 ms. The slope of the linear response region of observed injection duration to commanded injection duration was 8.4. Due to plenum effects, the average observed injection duration of the entire PSC system was an order of magnitude longer than the commanded injection duration and was found to vary significantly with fuel supply pressure.

Internal combustion engine emissions are currently a major source of air pollution. The harmful impact of engine emissions can be reduced when engines are fuelled by alternatives to petrol and diesel such as natural gas. The use of lean burn technology in spark-ignition engines has been dominant; however, the lean burn technique can not economically satisfy the increasingly restricted future emission standards particularly for NOx emissions. In this thesis, the use of the stoichiometric air-fuel mixture with exhaust gas recirculation (EGR) technique in a spark ignition natural gas engine is investigated. The aim of the research is to optimize the key engine operating conditions in order to obtain the lowest NO emissions accompanied with low fuel consumption and high power. This is achieved via both experimental and computer simulation research. / PhD Doctorate

Thesis (M.S.)--University of Nevada, Reno, 2006. / "August, 2006." Includes bibliographical references. Online version available on the World Wide Web.

Thesis (M.S.)--West Virginia University, 1998. / Title from document title page. "December 1998." Document formatted into pages; contains ix, 104 p. : ill. (some col.). Includes abstract. Includes bibliographical references (p. 78-79).