Maximum size-density relationships (MSDR) are used to quantify differences across sites in the number of trees of a given size and species that can be supported per hectare. These relationships are important to managers who are trying to maximize basal area and wood volume. In my study, I examined MSDR across Alabama, Georgia, Louisiana, and Mississippi using US Forest Service, Forest Inventory and Analysis (FIA) data. I determined the impact of species-specific, specific gravity, functional traits, and environmental factors on MSDR using a quantile regression approach. Overall, I found that climatic factors had the greatest influence on MSDR, and that species shade and drought tolerance were more influential than specific gravity across the southeastern US.

The objectives of this research were twofold: a) to define the relationship between tooth withdrawal and specific gravity for southern pine lumber and four different plate-to-wood load orientations, and b) to demonstrate how these relationships could be applied to new lumber grades to predict tooth withdrawal performance so that additional testing would not be necessary. The four orientations investigated were: a.) LRAA - plate axis parallel to load and wood grain parallel to load. b.) LREA - plate axis perpendicular to load and wood grain parallel to load. c.) LRAE - plate axis parallel to load and wood grain perpendicular to load. d.) LREE - plate axis perpendicular to load and wood grain perpendicular to load. For the LRAA, LREA, LRAE, LREE orientations, the following sample sizes were respectively: 27, 22, 27, and 29. Results showed specific gravity and embedment gap were excellent predictors of ultimate tooth withdrawal stress for the LRAA orientation. However, neither specific gravity nor percentage of latewood significantly influenced the location of tooth withdrawal. For the LREA orientation, specific gravity alone was a good predictor of ultimate tooth withdrawal stress. Furthermore, the side of the joint test specimen where tooth withdrawal initiated was dependent on the wood piece with the lowest mean specific gravity. For the LRAE orientation, specific gravity was a marginal predictor of ultimate tooth withdrawal stress. For the LREE orientation, specific gravity was a decent predictor of ultimate tooth-withdrawal stress. / Master of Science

Em virtude de muitas dúvidas ainda existentes, referentes ao desempenho e durabilidade dos concretos com agregados de RCD reciclados, sua utilização até o momento é limitada, não chegando aos níveis desejáveis e necessários. Somam-se a essas, a falta de gestão, de ferramentas de controle de qualidade, de normalização e de melhoria nas operações unitárias de beneficiamento do RCD. Os agregados reciclados apresentam características físicas e comportamento bastante heterogêneo, o que dificulta sua utilização com confiabilidade, principalmente em situações que demandam um maior controle e responsabilidade por parte do material empregado, como no caso de concretos estruturais. A porosidade e absorção dos agregados reciclados influenciam, de maneira significativa, as propriedades do concreto fresco e endurecido. Mesmo que estes sejam separados por fases (concreto, argamassa e cerâmica), é possível encontrar porosidades variadas dentro de uma mesma fase. Portanto, não se pode afirmar que o comportamento de concretos com agregados de mesma fase será homogêneo. Por este motivo, para esta pesquisa os agregados reciclados vermelho (predominância visual de cerâmica vermelha) e cinza (predominância visual de materiais cimentícios) foram separados em quatro faixas de densidade (d<1,9; 1,9<d<2,2; 2,2<d<2,5; d>2,5 g/cm³). Foram analisados os resultados de resistência à compressão, módulo de elasticidade, absorção de água, índice de vazios, massa específica e consumo de cimento. Os resultados obtidos nos ensaios de avaliação das propriedades físicas e mecânicas dos concretos usando agregados vermelho e cinza e concretos com agregados convencionais foram analisados para quantificar a influência da porosidade dos agregados. Verificou-se que a influência da natureza mineralógica dos agregados (vermelho ou cinza) influenciou as propriedades de maneira menos intensa que sua porosidade. Além disso, os concretos produzidos com RCD de densidade inferior a 2,2 g/cm3 apresentaram menor resistência e módulo e maior absorção de água, tornando o concreto muito menos eficiente para aplicações estruturais. A separação dos agregados em faixas de densidade garantiu um comportamento bastante homogêneo dos concretos, quando se utilizou agregados da mesma faixa. Com isso, foi possível estabelecer uma correlação entre a porosidade dos agregados e o desempenho mecânico dos concretos. A separação por faixas de densidade se mostrou como um critério confiável de classificação e caracterização dos agregados para a fabricação de concretos, podendo ser utilizado em conjunto com a separação visual normalmente empregada. / Construction and Demolition Waste (CDW) aggregates have not yet been widely used in concrete applications due to the many doubts relating to its performance and durability. The lack of an appropriate CDW recycling management, standardization, an innovative process technology as well as faster, cheaper and accurate quality control techniques also limits the use of this material. The reliable use of recycled CDW aggregates, especially in major situations such as in structural concrete, is still difficult due to its heterogeneous physical characteristics and behavior. Fresh and hard concrete properties are significantly influenced by recycled aggregate porosity and water absorption. Even if aggregates are separated in phases by hand sorting (concrete, mortar and ceramics) it is possible to find different porosities within the same phase and, for that reason, concretes will also present heterogeneous behavior. In this direction, the two types of recycled aggregates used in this research – named red (mainly constituted of red ceramics) and grey (mainly constituted of cimenticious materials) – were separated in four density classes (d<1.9; 1.9<d<2.2; 2.2<d<2.5; d>2.5 g/cm³). The compressive strength, elastic modulus, water absorption, specific weight and cement consumption of concretes were analyzed. The mechanical and physical properties of concretes were studied in terms of the recycled aggregate porosity and comparisons of results obtained with concretes using red or grey recycled aggregates and with ordinary aggregates were carried out. It was verified that the concretes properties were mostly influenced by the aggregates porosity when compared to its phase. Recycled aggregates with bulk specific gravity under 2.2 g/cm3 provided a significant reduction of the compressive strength and the elastic modulus and an increase of water absorption, producing concretes less efficient for structural applications. The behaviour of concretes produced by aggregates within the same density class was found to be homogeneous. A relation between porosity of aggregates and mechanical performance of concrete was verified. The heavy media separation can be used, together with the hand sorting, as an efficient and reliable aggregate quality control method for the production of concretes.

Phytophthora infestans (Mont) de Bary is a devastating pathogen in potato producing regions around the world. Populations of the organism in Canada shifted during the mid-1990’s as the US-1 strain (A1, metalaxyl-sensitive) was displaced by the highly aggressive, US-8 strain (A2, metalaxyl-insensitive). An increase in the incidence and severity of late blight has followed. Late blight is controlled by cultural practices aimed at eliminating disease sources and by the application of foliar fungicides. Tubers can become infected at harvest from contact with blighted vines leading to severe losses in storage. In many production areas, growers desiccate vines two to three weeks prior to harvest to reduce late blight tuber rot. However, in Manitoba, because of the loss of potential yield that results from vine killing prior to harvest in a late maturing cultivar such as Russet Burbank, growers are reluctant to adopt this practice. The objective of this study was to develop recommendations for preharvest management practices that reduce storage losses due to late blight. Field trials were conducted in 1997 and 1998 to investigate the effect of vine desiccation with diquat and/or a late season application of chlorothalonil and copper hydroxide on yield, processing quality, and disease development in storage. Desiccating vines with diquat two weeks prior to harvest reduced yield and tuber size. Compared to the untreated control, the largest reductions in marketable yield were observed for the early September harvest. By the late September harvest, however, the effect of vine killing in reducing marketable yield was less apparent. Specific gravity was lower in the vine killed treatment for all harvest dates in 1997 and in the early and mid September harvests in 1998. Vine killing did not contribute to elevated levels of reducing sugars or consistently darker fry colour at harvest or during storage. Skin-set was improved when vines were desiccated for all harvest dates in 1997 and at the early September harvest date in 1998. Vine killing reduced tuber rot in storage caused by Fusarium dry rot and Pythium leak for the early and mid September harvest dates in 1997. The incidence of late blight tuber rot was reduced in storage for the early September harvest in 1998 when vines were desiccated. The late-season application of chlorothalonil and copper hydroxide did not reduce tuber rot in storage in storage either year. Results from this study indicate that vine killing two weeks before an early to mid- September harvest is not recommended in Manitoba because of reductions in yield and specific gravity. Alternative management practices to reduce late blight tuber rot in storage should be investigated. / February 2005

Materials derived from chicken feathers could be used advantageously in composite building material applications. Such applications could potentially consume the five billion pounds of feathers produced annually as a by-product of the U.S. poultry industry. To aid the development of successful applications for chicken feather materials (CFM), the physical and mechanical properties of processed CFM have been characterized in this research. Results describing the moisture content, aspect ratio, apparent specific gravity, chemical durability, Youngs modulus, and tensile strength for processed CFM and specifically their fiber and quill components are presented herein. Processed chicken feather fiber and quill samples were found to have similar moisture contents in the range of 16 - 20%. The aspect ratio (i.e., length/diameter) of samples were found to be in the range of 30 - 50, and the fiber material was found to have a larger aspect ratio than the quill material. A comparison with values in the literature suggests that different processing regimes produce CFM with higher aspect ratios. Samples were found to have apparent specific gravities in the range of 0.7 - 1.2, with the fiber material having a higher apparent specific gravity than the quill material. A comparison with values in the literature suggests that apparent specific gravity results vary with fiber length and approach the value for keratin as fiber length decreases and internal voids become increasingly accessible. Chemical durability results showed that CFM rapidly degrade in highly alkaline (pH=12.4) environments and are, thus, likely incompatible with cement-based materials without special treatment. The Youngs modulus of processed chicken feather materials was found to be in the range of 3 - greater than 50 GPa and, thus, comparable to the Youngs moduli of other natural fibers. The tensile strength of oven-dried samples was found to be in the range of 10 - greater than 70 MPa. In agreement with results in the literature, the fiber material was found to have a greater tensile strength than the quill material. Finally, a simplified approach for comparing the effective Youngs moduli and effective tensile strengths of various processed CFM samples was introduced.

In long term, to discover the genes responsible for wood production, genetic control of wood specific gravity (WSG) in Pinus brutia Ten. (Turkish red pine) open pollinated Ceyhan progeny trial, which was established with the seeds collected from 168 clones originated from six clonal Turkish red pine seed orchards was studied. Wood samples were taken by destructive sampling during the rouging of this trial at the age of seven. Specifically / (1) to examine the magnitude of family differences and its components for wood specific gravity (WSG) and growth traits (height, diameter and stem volume) / (2) to determine WSG inheritance and its genetic correlation with growth traits / and (3) to estimate breeding values of 168 families for the WSG and to predict genetic gain if selection is based on phenotypic, rouged and genotypic seed orchard by reselecting the best parents with respect to WSG. Differences among the 168 families for mean WSG was large (ranged from 0.35 to 0.44), as indicated by high individual (0.42+0.07) and family mean (0.55+0.03) heritabilities. Family differences and high heritabilities were also observed for all growth traits. Genetic correlations between WSG and growth traits were statistically insignificant (near zero), while low and insignificant negative phenotypic correlations among the same traits were observed. Realized genetic gain for single trait selection at age seven was insignificant (0.37 %) for WSG and 8.4 % for stem volume in phenotypic seed orchards. Average genetic gain in breeding zone after roguing, by leaving the best 20 clones in each seed orchard, reached 1.7 % for WSG and 16.1 % for stem volume. Genetic gain (relative to controls) at the age of seven obtained from the first generation genotypic seed orchards consisting the best 30 clones was estimated 5.2 % for WSG and 35 % for stem volume. Multi-trait selection was also proposed in this study for the same traits. Selection of best 10 families for the highest WSG and stem volume breeding values produce 5.6 % genetic gain for WSG and 27.7 % genetic gain for stem volume. For the future, the 168 families with known phenotypic and genotypic values regarding to WSG will be screened for the genes responsible for wood production.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite. The specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials such as silica, base metals and their oxides, usually associated with gravitation–gold–recovery processes. The ore body investigated in this project originated from a mined gold reef containing a large proportion of gold locked inside the gold pyrite complexes. In the mine's processing plant a gold pyrite concentrate was produced by means of a flotation process. The roasting process that followed, oxidized the pyrite to iron oxide (hematite) and sulphur dioxide. The gold particles which were locked up inside the pyrite gold complex were exposed or liberated, allowing the chemicals to penetrate the complex and dissolve the gold. After the cyanide gold extraction process, the material was pumped on to a mine reserve dump, referred to as tailings or tailings reserve dump. The tailings usually contain iron oxides, free gold, gold associated with iron oxides and gold associated with silica, and free silica, commonly referred to as calcine. The gold content on the calcine dump was significantly lower than the flotation concentrate before the extraction of the gold and it was no longer viable for the mine to process the tailings further. As the volume of the mine reserve dump increased over the years, it became viable to recover the gold in a high volume low grade plant. Several attempts were made to recover the gold in this dump, but due to the high cost of processing and milling the material, it was not done. The norm in the mining industry is that it is impossible to concentrate the gold by means of gravity separation techniques where the average particle sizes are smaller than 50 um in diameter and upgrading with inexpensive gravity separation techniques was ruled out by the mine, because the average particle sizes were too small. The dump investigated in this project differed from other reserve dumps in that the main phase of material in this dump was hematite and not silica. A suspension of this material would have different fall–out properties than other mine reserve dumps, because of the hematite's high specific gravity compared to silica. This property of the material birthed the idea that the material will respond positively to high acceleration separation, although the particle sizes were too small for effective upgrading according to the norm in the mining industry. Using acceleration concentration as a first stage in the gold recovery process the production cost per gram of gold produced could be reduced significantly. Firstly, the volume of concentrated material to be treated in the chemical extraction process was reduced ninety percent and secondly, the gold concentration was increased significantly. If the gold could be concentrated to more than twenty grams of gold per ton, it could be extracted economically with an aggressive chemical processes. This was not possible with low grade material contained in the dump. The theoretical principle, on which this project was based, was to make use of high acceleration separation to establish separation between the particles associated with the gold, and the particles not associated with gold. Applying a high gravitational force would have an influence on the velocity by which the particles would fall–out in a suspension. As the acceleration force increased the fall–out velocity would also be increased and the particles with higher specific gravity would be affected more. A factor that was equally important was the particle size and weight distribution. A large hematite particle would compete with a small gold particle due to the similarity in weight. This could cause loss in small gold particles or retention of hematite particles with no gold content. Very little scientific information was available on the material investigated and in order to assemble a concentration plant setup, the head grade and particle size distribution for both the dump and bulk sample were determined accurately. Thereafter, chemical analyses and mineralogical examination were done on a representative sample of the bulk sample, determining the chemical composition of the material. The results obtained thereof were evaluated and used to configure a pilot plant. A large bulk sample was processed in the pilot plant and from the analytical results the efficiency could be evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes. / Thesis (M.Sc. Engineering Sciences (Chemical and Minerals Engineering))--North-West University, Potchefstroom Campus, 2012.

Phytophthora infestans (Mont) de Bary is a devastating pathogen in potato producing regions around the world. Populations of the organism in Canada shifted during the mid-1990’s as the US-1 strain (A1, metalaxyl-sensitive) was displaced by the highly aggressive, US-8 strain (A2, metalaxyl-insensitive). An increase in the incidence and severity of late blight has followed. Late blight is controlled by cultural practices aimed at eliminating disease sources and by the application of foliar fungicides. Tubers can become infected at harvest from contact with blighted vines leading to severe losses in storage. In many production areas, growers desiccate vines two to three weeks prior to harvest to reduce late blight tuber rot. However, in Manitoba, because of the loss of potential yield that results from vine killing prior to harvest in a late maturing cultivar such as Russet Burbank, growers are reluctant to adopt this practice. The objective of this study was to develop recommendations for preharvest management practices that reduce storage losses due to late blight. Field trials were conducted in 1997 and 1998 to investigate the effect of vine desiccation with diquat and/or a late season application of chlorothalonil and copper hydroxide on yield, processing quality, and disease development in storage. Desiccating vines with diquat two weeks prior to harvest reduced yield and tuber size. Compared to the untreated control, the largest reductions in marketable yield were observed for the early September harvest. By the late September harvest, however, the effect of vine killing in reducing marketable yield was less apparent. Specific gravity was lower in the vine killed treatment for all harvest dates in 1997 and in the early and mid September harvests in 1998. Vine killing did not contribute to elevated levels of reducing sugars or consistently darker fry colour at harvest or during storage. Skin-set was improved when vines were desiccated for all harvest dates in 1997 and at the early September harvest date in 1998. Vine killing reduced tuber rot in storage caused by Fusarium dry rot and Pythium leak for the early and mid September harvest dates in 1997. The incidence of late blight tuber rot was reduced in storage for the early September harvest in 1998 when vines were desiccated. The late-season application of chlorothalonil and copper hydroxide did not reduce tuber rot in storage in storage either year. Results from this study indicate that vine killing two weeks before an early to mid- September harvest is not recommended in Manitoba because of reductions in yield and specific gravity. Alternative management practices to reduce late blight tuber rot in storage should be investigated.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite. The specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials such as silica, base metals and their oxides, usually associated with gravitation–gold–recovery processes. The ore body investigated in this project originated from a mined gold reef containing a large proportion of gold locked inside the gold pyrite complexes. In the mine's processing plant a gold pyrite concentrate was produced by means of a flotation process. The roasting process that followed, oxidized the pyrite to iron oxide (hematite) and sulphur dioxide. The gold particles which were locked up inside the pyrite gold complex were exposed or liberated, allowing the chemicals to penetrate the complex and dissolve the gold. After the cyanide gold extraction process, the material was pumped on to a mine reserve dump, referred to as tailings or tailings reserve dump. The tailings usually contain iron oxides, free gold, gold associated with iron oxides and gold associated with silica, and free silica, commonly referred to as calcine. The gold content on the calcine dump was significantly lower than the flotation concentrate before the extraction of the gold and it was no longer viable for the mine to process the tailings further. As the volume of the mine reserve dump increased over the years, it became viable to recover the gold in a high volume low grade plant. Several attempts were made to recover the gold in this dump, but due to the high cost of processing and milling the material, it was not done. The norm in the mining industry is that it is impossible to concentrate the gold by means of gravity separation techniques where the average particle sizes are smaller than 50 um in diameter and upgrading with inexpensive gravity separation techniques was ruled out by the mine, because the average particle sizes were too small. The dump investigated in this project differed from other reserve dumps in that the main phase of material in this dump was hematite and not silica. A suspension of this material would have different fall–out properties than other mine reserve dumps, because of the hematite's high specific gravity compared to silica. This property of the material birthed the idea that the material will respond positively to high acceleration separation, although the particle sizes were too small for effective upgrading according to the norm in the mining industry. Using acceleration concentration as a first stage in the gold recovery process the production cost per gram of gold produced could be reduced significantly. Firstly, the volume of concentrated material to be treated in the chemical extraction process was reduced ninety percent and secondly, the gold concentration was increased significantly. If the gold could be concentrated to more than twenty grams of gold per ton, it could be extracted economically with an aggressive chemical processes. This was not possible with low grade material contained in the dump. The theoretical principle, on which this project was based, was to make use of high acceleration separation to establish separation between the particles associated with the gold, and the particles not associated with gold. Applying a high gravitational force would have an influence on the velocity by which the particles would fall–out in a suspension. As the acceleration force increased the fall–out velocity would also be increased and the particles with higher specific gravity would be affected more. A factor that was equally important was the particle size and weight distribution. A large hematite particle would compete with a small gold particle due to the similarity in weight. This could cause loss in small gold particles or retention of hematite particles with no gold content. Very little scientific information was available on the material investigated and in order to assemble a concentration plant setup, the head grade and particle size distribution for both the dump and bulk sample were determined accurately. Thereafter, chemical analyses and mineralogical examination were done on a representative sample of the bulk sample, determining the chemical composition of the material. The results obtained thereof were evaluated and used to configure a pilot plant. A large bulk sample was processed in the pilot plant and from the analytical results the efficiency could be evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes. / Thesis (M.Sc. Engineering Sciences (Chemical and Minerals Engineering))--North-West University, Potchefstroom Campus, 2012.

Phytophthora infestans (Mont) de Bary is a devastating pathogen in potato producing regions around the world. Populations of the organism in Canada shifted during the mid-1990’s as the US-1 strain (A1, metalaxyl-sensitive) was displaced by the highly aggressive, US-8 strain (A2, metalaxyl-insensitive). An increase in the incidence and severity of late blight has followed. Late blight is controlled by cultural practices aimed at eliminating disease sources and by the application of foliar fungicides. Tubers can become infected at harvest from contact with blighted vines leading to severe losses in storage. In many production areas, growers desiccate vines two to three weeks prior to harvest to reduce late blight tuber rot. However, in Manitoba, because of the loss of potential yield that results from vine killing prior to harvest in a late maturing cultivar such as Russet Burbank, growers are reluctant to adopt this practice. The objective of this study was to develop recommendations for preharvest management practices that reduce storage losses due to late blight. Field trials were conducted in 1997 and 1998 to investigate the effect of vine desiccation with diquat and/or a late season application of chlorothalonil and copper hydroxide on yield, processing quality, and disease development in storage. Desiccating vines with diquat two weeks prior to harvest reduced yield and tuber size. Compared to the untreated control, the largest reductions in marketable yield were observed for the early September harvest. By the late September harvest, however, the effect of vine killing in reducing marketable yield was less apparent. Specific gravity was lower in the vine killed treatment for all harvest dates in 1997 and in the early and mid September harvests in 1998. Vine killing did not contribute to elevated levels of reducing sugars or consistently darker fry colour at harvest or during storage. Skin-set was improved when vines were desiccated for all harvest dates in 1997 and at the early September harvest date in 1998. Vine killing reduced tuber rot in storage caused by Fusarium dry rot and Pythium leak for the early and mid September harvest dates in 1997. The incidence of late blight tuber rot was reduced in storage for the early September harvest in 1998 when vines were desiccated. The late-season application of chlorothalonil and copper hydroxide did not reduce tuber rot in storage in storage either year. Results from this study indicate that vine killing two weeks before an early to mid- September harvest is not recommended in Manitoba because of reductions in yield and specific gravity. Alternative management practices to reduce late blight tuber rot in storage should be investigated.