No description available.

No description available.

No description available.

No description available.

No description available.

This thesis deals with the development and numerical modeling of Fiber Reinforced Polymer (FRP) wind turbine towers and luminaires. More specifically, this project is designed to capitalize on the technologies developed at the University of Manitoba to design FRP composite structures for use in remote communities where the costs of transportation and erection make the use of steel towers prohibitive. The work presented includes the analysis of a 50 m tall 750 kW wind turbine tower according to International Electrotechnical Commission (IEC) and Canadian Standard Association (CSA) standards using Glass Fiber Reinforced Polymer (GFRP), Carbon Fiber Reinforced Polymer (CFRP) and conventional steel. Standard luminaires, 6 m and 12 m, were also designed according to American Association of State Highway and Transportation Officials (AASHTO) standards for highway luminaires. The results showed that FRP can be effectively used as an alternative material for wind turbine towers and luminaires. Fiber Reinforced Polymer (FRP) composite wind turbine towers and luminaires studied in this project are lighter than similar structures fabricated using steel. Furthermore, these structures also meet the structural performance requirements set by AASHTO, IEC and CSA standards. / October 2016

No description available.

The performance requirements of turbofan engines demands a stability and transient capability beyond that associated with the past generations of gas turbine engines. The axial flow fan unit is most vulnerable to loading limitations due to the primary problems associated with the compression process, its sensitivity to inlet distortion and the difficulty to design for an overall optimum blade duty in a machine of wide radial blade loading distribution. The development of mathematical models with some capability of predicting the stable operating range of an axial flow fan has to overcome the difficulties associated with the modelling of the radially distinct flow regions and their dynamic interaction. ' The current investigation combined the available knowledge of one-dimensional models (based on the principles of conservation of mass, linear momentum and energy) with the assumptions of the parallel compressor theory, in order to develop a linearized system of equations for stability analysis (surge prediction). The stability conditions which emerged from this approach were applied on the experimentally derived characteristics of a low hub to tip ratio split flow fan in a manner which involved the modelling of the dynamic interaction of the inner and outer flow region of the fan. The development of the governing equations was achieved by applying one-dimensional flow analysis to the inner and outer section of the fan. Their interaction was modelled on the experimentally obtained radial movement of the splitter streamline and the discharge ,static pressure 'radial distribution. The inner and outer region were treated as a lumped volume element search operating on a local masflow averaged total pressure rise characteristic and alternatively acting in conjunction with a common nozzle and separate nozzles. The experimental investigation was carried out on a low hub totipratio two-stage split flow fan(with the facility of independent bypass and core throttles)in order to examine the localised and overall performance of such a fan(and the staling processes involved)and to enable the application of the stability analysis. The influence of reducing the distance between the fan flow spliter and the last bladerowasal so investigated, «The mathematical mode1s predicted the point of dynamic instability within 4.52 of the experimental observed mas flow rate and pressure is value.

The ingestion of hot mainstream gas into the wheel-space between the rotor and staler discs is one of the most important internal cooling problems for gas turbine designers. To solve this problem, engineers design a rim seal at the periphery of wheel-space and direct a sealing flow from the internal cooling system to prevent ingress. The main aim of this thesis is to build a simple computational model to predict the scaling effectiveness of externally-induced ingress for engine designers. The axisymmetric model represents a gas turbine wheel-space and provides useful information related to the fluid dynamics and heat transfer in the wheel-space. At the same time, this model saves much computation time and cost for engine designers who currently use complex and time-consuming 3D models. The- computational model in this -thesis is called the prescribed ingestion model. Steady simulations are carried out using the commercial CFD code, ANSYS CFX with meshes built using ICEM CFD. Boundary conditions are applied at the ingress inlet of the model using experimental measurements and a mass-based averaging procedure. Computational parameters such as rotational Reynolds number, non-dimensional sealing flow rate and thermal conditions on the rotor are selected to investigate the fluid dynamics and heat transfer at typical experimental rig operating conditions. Different rim seal geometries arc investigated and results are compared with experimental data. In addition to the prescribed ingestion model, two typical axisymmetric rotor-stator system models without ingress arc established. The aim of these rotor-stator models is to investigate the fluid dynamics and heat transfer of the wheel-space in the situation without ingress. The effects of geometry and turbulence model also arc studied in these simulations. Most results from these simulations are in good agreement with experimental data from the literature, which enhances confidence in the prescribed Ingestion model.

The low pressure (LP) exhaust system presents a promising avenue for improving the performance of large steam turbines. For this reason, LP exhaust systems have attracted the attention of the research community for decades. Nevertheless, we still lack understanding of the flow physics and loss mechanisms in the exhaust system, especially at part-load conditions. It is also unclear how the exhaust system should be designed when its required operating range widens. This thesis provides solutions to these aerodynamic issues through experimental and numerical investigations, and provides tools that could contribute to better designs of LP exhaust systems. Firstly, the Computational Fluid Dynamics (CFD) solver ANSYS CFX was validated against experiments performed on a scaled test rig under representative part-load flow conditions. This validation exposed the weakness of Reynolds-averaged Navier-Stokes (RANS) CFD when there is a highly swirling flow and large separation regions in the exhaust diffuser. To facilitate the numerical studies, a series of tools were also developed. A design suite, ExhaustGen, was used to automate the pre- and post-processing of CFD calculations. The exhaust diffuser was parametrised using "Minimum Energy Curves", which reduce the dimension of parameter space. Further, a suitable stage-hood interface treatment (Multiple Mixing Planes) was chosen to predict the circumferentially non-uniform flow in the exhaust hood at low computational cost. Numerical investigation of the baseline geometry provided insights into the key flow features and loss mechanisms in the exhaust system, over a wide range of operating conditions. In particular, the bearing cone separation was identified as a key source of loss at part-load conditions. The effect of stage-hood interaction on the performance and design of the exhaust system was studied by varying the rotor blade design, which can positively influence system performance. Finally, a global sensitivity study was performed to identify the most influential design parameters of the exhaust hood. These findings allow, for the first time, LP exhaust hood performance maps to be constructed, so that the benefits of choosing a suitable hood geometry and blade design can be revealed. The thesis also offers contribution towards formulating LP exhaust system design guidance for a wide operating range.