Non-metallic inclusions in steels are generally considered to be detrimental for mechanical properties. However, it has been recognized that certain inclusions, such as Ti-oxide and TiN, can serve as potent nucleation sites for the formation of intragranular ferrite (IGF) in low-alloy steels. The formation of IGF could improve the toughness of the coarse grained heat affected zone (CGHAZ) of weld metals. Thus, the present thesis mainly focuses on the effect of size of nucleation sites on the IGF formation. Quantitative studies on the composition, size distribution and nucleation probability for each size of the inclusions as well as the area fraction, starting temperature and morphology of an IGF have been carried out. In the present work, the Ti-oxide and TiN powders were mixed with metallic powders. The mixed powders were heated up to the liquid state and cooled with a slow cooling rate of 3.6 ºC/min. These as-cast steels with Ti-oxide and TiN additions were used to simulate the IGF formation in the CGHAZ of weld metals. Specifically, the inclusion and microstructure characteristics in as-cast steels have been investigated. The results show that the nucleant inclusion was identified as a TiOx+MnS phase in steels with Ti2O3 additions and as a TiN+Mn-Al-Si-Ti-O+MnS phase in steels with TiN additions. In addition, the TiOx and TiN phases are detected to be the effective nucleation sites for IGF formation. It is clearly shown that an increased inclusion size leads to an increased probability of IGF nucleation. This probability of IGF nucleation for each inclusion size of the TiOx+MnS inclusions is clearly higher than that of the complex TiN+Mn-Al-Si-Ti-O+MnS inclusions. In addition, the area fraction of IGF in the steels with Ti2O3 additions is larger than that of the steels with TiN additions. This result agrees with the predicted tendency of the probability of IGF nucleation for each inclusion size in the steels with Ti2O3 and TiN additions. In order to predict the effective inclusion size for IGF formation, the critical diameters of the TiO, TiN and VN inclusions, which acted as the nucleation sites of IGF formation, were also calculated based on the classical nucleation theory. The critical diameters of TiO, TiN and VN inclusions for IGF formation were found to be 0.192, 0.355 and 0.810 μm in the present steels. The calculation results were found to be in agreement with the experiment data of an effective inclusion size. Moreover, the effects of the S, Mn and C contents on the critical diameters of inclusions were also calculated. It was found that the critical diameter of the TiO, TiN and VN inclusions increases with an increased content of Mn or C. However, the S content doesn’t have a direct effect on the critical diameter of the inclusions for IGF formation. The probability of IGF nucleation for each inclusion size slightly decreases in the steel containing a higher S content. This fact is due to that an increased amount of MnS precipitation covers the nucleant inclusion surface. In the as-cast experiment, it was noted that an IGF can be formed in steels with Ti2O3 and TiN additions with a cooling rate of 3.6 ºC/min. In order to control the microstructure characteristics, such as the area fraction and the morphology of an IGF, and to investigate the starting temperature of IGF and grain boundary ferrite (GBF) formation, the dynamic transformation behavior of IGF and GBF was studied in-situ by a high temperature confocal laser scanning microscope (CLSM). Furthermore, the chemical compositions of the inclusions and the morphology of IGF after the in-situ observations were investigated by using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and electron probe microanalysis (EPMA) which equipped wavelength dispersive spectrometer (WDS). The results show that the area fraction of IGF is larger in the steels with Ti2O3 additions compared to the steels with TiN additions, after the same thermal cycle has been imposed. This is due to that the TiOx phase provides more potent nucleation sites for IGF than the TiN phase does. Also, the area fraction of IGF in the steels is highest after at an intermediate cooling rate of 70 ºC/min, since the competing phase transformations are avoided. This fact has been detected by using a hybrid methodology in combination with CLSM and differential scanning calorimetry (DSC). In addition, it is noted that the morphology of an IGF is refined with an increased cooling rate. / <p>QC 20150325</p>

Lightweight cellular concrete (LCC) is mainly a mixture of water, cement, and foam bubbles. LCC generally has a cast density between 20-60 pcf and an air content between 49-84%. LCC is often used as a fill material because it has a low unit weight which reduces settlement. LCC is increasingly being considered as a backfill behind Mechanically Stabilized Earth (MSE) walls and embankments. Although engineers are using LCC in MSE walls or free face walls (MSE wall without the concrete panels or reinforcements), there is presently a lack of information regarding the performance and behavior of LCC to guide them. This research attempts to answer questions on the design of MSE walls backfilled with LCC and free face LCC walls by providing a well-documented case history and evaluating if LCC can be modeled as a c-ϕ material. A steel frame test box (10 ft wide x 12 ft long x 10 ft high) with a MSE wall on one side was constructed for the research. The box was filled with four lifts of LCC with steel ribbed-strip reinforcements extending into the LCC behind the MSE wall panels at the center of each lift. After the LCC was cured, two static load tests were performed by applying a surcharge load to the surface of the LCC. In one test, surcharge pressure was applied adjacent to the MSE wall to produce failure of the wall system. In a second test, the surcharge pressure was placed adjacent to a free face of the LCC to produce failure. String potentiometers (string pots), load cells, pressure plates, and strain gages were used to measure the behavior of the MSE wall and free face wall during testing. These two tests provided a comparison between LCC behavior with a MSE wall relative to a LCC free face. Failure of the free face wall with unreinforced LCC backfill in this test can be predicted using Rankine’s lateral force equation using a c-ϕ model. Failure angle at the base of the free face wall was between 51-63° which corresponds with an average friction angle (ϕ) of 24° and cohesion (c) of 1575 psf with an upper bound ϕ = 34° and a c = 1285 psf. The presence of reinforcements in the LCC backfill behind the MSE wall increased the capacity of the wall to hold a surcharge load. The presence of reinforcements in the LCC behind MSE walls also led to a much more ductile surcharge pressure vs. lateral deflection curve for the MSE wall compared to the free face wall.

No description available.

La profondeur possible d’imagerie en laser-scanning microscopie est limitée non seulement par la distance de travail des lentilles de objectifs mais également par la dégradation de l’image causée par une atténuation et une diffraction de la lumière passant à travers l’échantillon. Afin d’étendre cette limite, il est possible, soit de retourner le spécimen pour enregistrer les images depuis chaque côté, or couper progressivement la partie supérieure de l’échantillon au fur et à mesure de l‘acquisition. Les différentes images prises de l’une de ces manières doivent ensuite être combinées pour générer un volume unique. Cependant, des mouvements de l’échantillon durant les procédures d’acquisition engendrent un décalage non seulement sur en translation selon les axes x, y et z mais également en rotation autour de ces même axes, rendant la fusion entres ces multiples images difficile. Nous avons développé une nouvelle approche appelée 2D-SIFT-in-3D-Space utilisant les SIFT (scale Invariant Feature Transform) pour atteindre un recalage robuste en trois dimensions de deux images. Notre méthode recale les images en corrigeant séparément les translations et rotations sur les trois axes grâce à l’extraction et l’association de caractéristiques stables de leurs coupes transversales bidimensionnelles. Pour évaluer la qualité du recalage, nous avons également développé un simulateur d’images de laser-scanning microscopie qui génère une paire d’images 3D virtuelle dans laquelle le niveau de bruit et les angles de rotations entre les angles de rotation sont contrôlés avec des paramètres connus. Pour une concaténation précise et naturelle de deux images, nous avons également développé un module permettant une compensation progressive de la luminosité et du contraste en fonction de la distance à la surface de l’échantillon. Ces outils ont été utilisés avec succès pour l’obtention d’images tridimensionnelles de haute résolution du cerveau de la mouche Drosophila melanogaster, particulièrement des neurones dopaminergiques, octopaminergiques et de leurs synapses. Ces neurones monoamines sont particulièrement important pour le fonctionnement du cerveau et une étude de leur réseau et connectivité est nécessaire pour comprendre leurs interactions. Si une évolution de leur connectivité au cours du temps n’a pas pu être démontrée via l’analyse de la répartition des sites synaptiques, l’étude suggère cependant que l’inactivation de l’un de ces types de neurones entraine des changements drastiques dans le réseau neuronal. / Although laser scanning microscopy is a powerful tool for obtaining thin optical sections, the possible depth of imaging is limited by the working distance of the microscope objective but also by the image degradation caused by the attenuation of both excitation laser beam and the light emitted from the fluorescence-labeled objects. Several workaround techniques have been employed to overcome this problem, such as recording the images from both sides of the sample, or by progressively cutting off the sample surface. The different views must then be combined in a unique volume. However, a straightforward concatenation is often not possible, because the small rotations that occur during the acquisition procedure, not only in translation along x, y and z axes but also in rotation around those axis, making the fusion uneasy. To address this problem we implemented a new algorithm called 2D-SIFT-in-3D-Space using SIFT (scale Invariant Feature Transform) to achieve a robust registration of big image stacks. Our method register the images fixing separately rotations and translations around the three axes using the extraction and matching of stable features in 2D cross-sections. In order to evaluate the registration quality, we created a simulator that generates artificial images that mimic laser scanning image stacks to make a mock pair of image stacks one of which is made from the same stack with the other but is rotated arbitrarily with known angles and filtered with a known noise. For a precise and natural-looking concatenation of the two images, we also developed a module progressively correcting the sample brightness and contrast depending on the sample surface. Those tools we successfully used to generate tridimensional high resolution images of the fly Drosophila melanogaster brain, in particular, its octopaminergic and dopaminergic neurons and their synapses. Those monoamine neurons appear to be determinant in the correct operating of the central nervous system and a precise and systematic analysis of their evolution and interaction is necessary to understand its mechanisms. If an evolution over time could not be highlighted through the pre-synaptic sites analysis, our study suggests however that the inactivation of one of these neuron types triggers drastic changes in the neural network.

<p>A new kind of lipid/polymer composite particle, consisting of a biodegradable polymer matrix with well-defined lipid domains, has been created. The lipid used is the water-swelling lipid monoolein (MO), which forms a reversed bicontinuous cubic diamond structure in aqueous solutions. The polymer is poly(d,l-lactide-co-glycolide) (PLG), which degrades into water-soluble monomers through hydrolysis. This new particle might be a good alternative for encapsulation of active substances intended to be released over a longer period of time, i.e. sustained/retained/controlled release.</p><p>To prepare such particles can be difficult. Suitable phase behaviour and a solvent with the right properties are needed. For this reason, the phase behaviours of several different lipid/polymer/solvent/water systems have been explored. From the phase behaviour of a suitable system (i.e. MO/PLG/ethyl acetate/water), a route for formation of lipid/polymer composite particles has been deduced. Particles have been formed and distinct, water-swelling, lipid domains have been confirmed by characterization by means of confocal laser scanning probe microscopy (CLSM). </p><p>The sample preparation process has been automated and a method based on using a robotic liquid handler has been developed. Phase diagrams have been determined by examination of macroscopic behaviours and the microstructures of the phases have been studied by small- and wide-angle X-ray scattering (L₃, V₂, L_α, L), nuclear magnetic resonance self-diffusion (L, L₃), viscosimetry (L) and rheology (L). Several different theoretical models have been applied for interpretation of the results. For example, the swelling of the reversed bicontinuous cubic phases and the sponge phase have been modelled by applying the theory of infinite periodical minimal surfaces, the sponge phase has been shown to be bicontinuous according to the theory of interconnected rods and the phase behaviour of the polymer has been described by the Flory-Huggins theory. The main focus of this work (4/5) concerns phase studies in multicomponent systems from a physical-chemical point of view.</p>

A new kind of lipid/polymer composite particle, consisting of a biodegradable polymer matrix with well-defined lipid domains, has been created. The lipid used is the water-swelling lipid monoolein (MO), which forms a reversed bicontinuous cubic diamond structure in aqueous solutions. The polymer is poly(d,l-lactide-co-glycolide) (PLG), which degrades into water-soluble monomers through hydrolysis. This new particle might be a good alternative for encapsulation of active substances intended to be released over a longer period of time, i.e. sustained/retained/controlled release. To prepare such particles can be difficult. Suitable phase behaviour and a solvent with the right properties are needed. For this reason, the phase behaviours of several different lipid/polymer/solvent/water systems have been explored. From the phase behaviour of a suitable system (i.e. MO/PLG/ethyl acetate/water), a route for formation of lipid/polymer composite particles has been deduced. Particles have been formed and distinct, water-swelling, lipid domains have been confirmed by characterization by means of confocal laser scanning probe microscopy (CLSM). The sample preparation process has been automated and a method based on using a robotic liquid handler has been developed. Phase diagrams have been determined by examination of macroscopic behaviours and the microstructures of the phases have been studied by small- and wide-angle X-ray scattering (L3, V2, Lα, L), nuclear magnetic resonance self-diffusion (L, L3), viscosimetry (L) and rheology (L). Several different theoretical models have been applied for interpretation of the results. For example, the swelling of the reversed bicontinuous cubic phases and the sponge phase have been modelled by applying the theory of infinite periodical minimal surfaces, the sponge phase has been shown to be bicontinuous according to the theory of interconnected rods and the phase behaviour of the polymer has been described by the Flory-Huggins theory. The main focus of this work (4/5) concerns phase studies in multicomponent systems from a physical-chemical point of view.

Sphaerodoridae is a group of benthic marine worms (Annelida) characterized by the presence of spherical tubercles covering their whole surface. They are commonly considered as belonging to Phyllodocida although sistergroup relationships are still far from being understood. Primary homology assessments of their morphological features are lacking, hindering the appraisal of evolutionary relationships between taxa. Therefore, our detailed morphological investigation focuses on different Sphaerodoridae as well as on other members of Phyllodocida using an integrative approach combining scanning electron microscopy (SEM) as well as immunohistochemistry with standard neuronal (anti-5-HT) and muscular (phalloidin-rhodamine) markers and subsequent CLSM analysis of whole mounts and sections. Furthermore, we provide histological (HES) and light microscopical data to shed light on the structures and hypothetical function of sphaerodorid key morphological features. We provide fundamental details into the sphaerodorid morphology supporting a Phyllodocida ancestry of these enigmatic worms. However, the muscular arrangement and the presence of an axial muscular pharynx is similar to conditions observed in other members of the Errantia too. Furthermore, nervous system and muscle staining as well as SEM and histological observations of different types of tubercles indicate a homology of the so called microtubercles, present in the long-bodied sphaerodorids, to the dorsal cirri of other Errantia. The macrotubercles seem to represent a sphaerodorid autapomorphy based on our investigations. Therefore, our results allow comparisons concerning morphological patterns between Sphaerodoridae and other Phyllodocida and constitute a starting point for further comparative investigations to reveal the evolution of the remarkable Sphaerodoridae.