Chitosan, Whey Protein Isolate (WPI) and vital wheat gluten (WG) are three biomaterials that have quite promising properties for packaging purposes. They have good film forming properties and good gas barrier properties in dry conditions. Moreover, because they are produced from industrial waste of food processing, they offer an ecological advantage over polymers made from petroleum. However, their physicochemical characteristics still must be improved for them to be of commercial interest for the food packaging industry. The purpose of this work was to study different strategies aiming to improve the water resistance and aging properties of these polymers, which are some of the key disadvantages of these materials. The produced solution cast chitosan and WPI films were characterised with scanning electron microscopy (SEM), density measurements and thermogravimetry. The water vapour transmission rate was determined at a relative humidity of 11%. In the first part, mechanical properties of solid films and seals were assessed by tensile testing. WG film’s tensile properties and oxygen and water vapour permeabilities were measured as a function of aging time. The changes in the protein structure were determined by infrared spectroscopy and size-exclusion high-performance liquid chromatography and the film structure was revealed by optical and scanning electron microscopy. Gluten-clay nanocomposites were characterised by tensile testing, X-ray diffraction and transmission electron microscopy. The incorporation of a hydrophobic biodegradable polymer, poly ( ε-caprolactone), PCL, in both chitosan and whey protein, yielded a significant decrease in water vapour transmission rate. It was observed that a certain amount of the PCL particles were ellipsoidal in chitosan and fibrous in WPI. The obtained data also indicated that the particle shape had an important influence in the water vapour transmission rate. In the second part, the aging properties of WG films, plasticized with glycerol and cast from water/ethanol solutions with pH=4 or pH=11 were investigated. WG films made from alkaline solutions were mechanically more time-stable than the acidic ones, the latter being initially very ductile but turning brittle towards the end of the aging period. The protein solubility measurements indicated that the protein structure of the acidic films was initially significantly less aggregated than the in basic films. During aging the acidic films lost more mass than the basic films through slow evaporation of volatiles (water/ethanol) and through migration of glycerol to the paper support. The oxygen permeability was also lower for the basic films. In the last part, the properties of new and aged glycerol-plasticized WG films at acidic and basic conditions containing ≤4.5 wt% natural or quaternary-ammonium-salt-modified montmorillonite were studied. Films of WG with montmorillonite were possible to produce by solution casting. The aging rate of acidic and basic films was unaffected by the incorporation of clay. However, the large reduction in water vapour permeability for most systems suggested that the clay sheets were evenly distributed within the films. The film prepared from basic solution and containing natural clay was almost completely exfoliated as revealed by transmission electron microscopy and X-ray diffraction. The best water vapour barrier properties were obtained by using modified clay. / QC 20101013

<p>The use of synthetic materials for tissue and organ reconstruction, i. e. tissue engineering, has become a promising alternative to current surgical therapies and may overcome the shortcomings of the methods in use today. The challenge is in the design and reproducible fabrication of biocompatible and bioresorbable polymers, with suitable surface chemistry, desirable mechanical properties, and the wanted degradation profile. These material properties can be achieved in various manners, including the synthesis of homo- and copolymers along with linear and star-shaped architectures. In many applications the materials’ three-dimensional structure is almost as important as its composition and porous scaffolds with high porosity and interconnected pores that facilitate the in-growth of cells and transportation of nutrients and metabolic waste is desired.</p><p>In this work linear and star-shaped polymers have been synthesized by ring-opening polymerization using a stannous-based catalyst and a spirocyclic tin initiator. A series of linear copolymers with various combinations of 1,5-dioxepane-2-one (DXO), Llactide (LLA) and ε-caprolactone (CL) have been polymerized using stannous octoate as catalyst. It is shown that the composition of the polymers can be chosen in such a manner that the materials’ mechanical and thermal properties can be predetermined. A solvent-casting and particulate leaching scaffold preparation technique has been developed and used to create three-dimensional structures with interconnected pores. The achieved physical properties of these materials’ should facilitate their use in both soft and hard tissue regeneration.</p><p>Well defined star-shaped polyesters have been synthesized using a spirocyclic tin initiator where L-lactide was chosen as a model system for the investigation of the polymerization kinetics. Neither the temperature nor the solvent affects the molecular weight or the molecular weight distribution of the star-shaped polymers, which all show a molecular weight distribution below 1.19 and a molecular weight determined by the initial monomer-to-initiator concentration.</p>

Η εργασία αυτή επιχειρεί να επισημάνει και να ερμηνεύσει τις κυρίαρχες τάσεις που παρατηρούνται στις Α.Ξ.Ε. (Άμεσες Ξένες Επενδύσεις) που πραγματοποιούνται από χώρες-μέλη των BRICS στην Αφρική αξιοποιώντας τα υπάρχοντα θεωρητικά υποδείγματα. / This paper attempts to identify and interpret the dominant trends in FDIs (Foreign Direct Investments) made ​​by member countries of BRICS in Africa, utilizing existing theoretical models.

L'alcool polyvinylique a été fonctionnalisé avec des aldéhydes et des acides boroniques dans le but d'obtenir des polymères pouvant apporter de la brillance tout en étant solubles dans les formulations de rouges à lèvres ou de vernis à ongles. De bons taux de fonctionnalisation ont été obtenus permettant d'avoir une bibliothèque de poly(vinyl acétals) et de poly(vinyl esters boroniques) d'une cinquantaine de polymères. Une multi-fonctionnalisation du PVA a été effectuée pour obtenir des polymères alliant ces deux propriétés. Cinq poly(vinyl acétals) ont ainsi permis d'apporter une forte brillance à des rouges à lèvres. La E-poly-L-lysine a également été fonctionnalisée avec diverses cétones afin d'obtenir de nouvelles poly-4-imidazolidinones. Ces polymères sont prometteurs pour des applications dans des produits cosmétiques tels que des soins. Ils ont également été utilisés en catalyse organique asymétrique.

The aim of this thesis is to determine the feasibility of an injectable delivery system based on 5-ethylene ketal ε-caprolactone for localized delivery of vascular endothelial growth factor (VEGF) and hepatocyte growth factor (HGF) for treating critical limb ischemia. HGF and VEGF were chosen because of their ability to simultaneously stimulate the proliferation and migration of endothelial cells, to initiate the formation of blood vessels and the recruitment of pericytes to stabilize the blood vessels. Homopolymer of 5-ethylene ketal ε-caprolactone and its copolymer with D,L-Lactide were synthesized by ring opening polymerization using hydrophobic initiator (octan-1-ol) or an hydrophilic initiator (MPEG), and stannous octanoate as a co-initiator/catalyst. The resulting polymers were amorphous and viscous liquids at room temperature. The viscosity, biodegradation rate, and release rate were varied by copolymerizing with D,L-lactide and/or initiating with MPEG or octan-1-ol. In vitro, the polymers degraded with surface erosion characterized by a nearly linear mass loss with time with no significant change in number average molecular weight and glass transition temperature. The ratio of EKC to DLLA in the copolymer remained the same throughout the degradation studies. A similar degradation mechanism was observed in vivo when the copolymer initiated with octan-1-ol was implanted subcutaneously in rats. In vivo, the polymer exhibited a moderate chronic inflammatory response, characterized by the presence of neutrophils, macrophages, fibroblasts and fibrous capsule formation. The inflammatory response decreased with time but was still on going after 18 weeks of subcutaneous implantation. Protein release from the polymer was transported by convection through the hydrated polymer region, at a rate determined by the osmotic pressure generated and the hydraulic conductivity of the polymer. Highly bioactive VEGF and HGF were released in a sustained manner, without burst effect for over 41 days when delivered simultaneously, using the osmotic release mechanism. VEGF was released at the rate of 36 ± 7 ng/day for 41 days, while HGF was released at the rate of 16 ± 2 ng/day for 70 days. Factors that influenced release of proteins were their solubility in the concentrated trehalose solution and hydraulic permeability of the polymer. This delivery system can serve as a potential vehicle for controlled release of VEGF and HGF for treating critical limb ischemia or the controlled release of other proteins for other clinical applications. / Thesis (Ph.D, Chemical Engineering) -- Queen's University, 2012-05-23 10:18:48.307

The flow pattern in the uphill teeming process has been found to be closely related to the quality of ingots and further to affect the yield of ingot production, which is crucial for the steel making process. The formation of non-metallic inclusion and entrapment of mold flux has been considered to be affected by the flow pattern in the gating system and molds by many previous researchers. The aim of this study is to investigate the flow pattern of steel in the gating system and molds during the initial filling stage. In addition, to study the utilization of swirl blade implemented at the bottom of the vertical runner on the improvement of initial filling condition in the mold. A three dimensional model of two molds gating system for 6.2 ton ingots from Scana Steel was adopted in the present work. A reduced geometry model including one mold and a runner, based on the method from previous researchers, was also used for comparison with the current more extensive model. Moreover, a reduced geometry model including one swirl blade and a runner was simulated to find effects of an increased-length vertical runner on the flow pattern improvement at the vertical runner outlet. Flow pattern, hump height and wall shear stress were respectively studied. A reduced geometry with homogenous inlet conditions fails to describe the fluctuating conditions present as the steel enters the mold. However, the trends are very similar when comparing the (hump height-surface height) evolution over time. The implementation of swirl blades gives a chaotic initial filling condition with a considerable amount of droplets being created when steel enters the molds during the first couple of seconds. However, a more calm filling condition with less fluctuation is achieved at the molds after a short while. Moreover, the orientation of the swirl blades affects he flow pattern of the steel. A proper placement of a swirl blade improves the initial filling conditions. The utilization of swirl blades might initially result in larger hump height. However, it gives fewer fluctuations as the casting proceeds. In the model without swirl blades, the maximum wall shear stress fluctuates with a descending trend as the filling proceeds. An implementation of swirl blades can decrease and stabilize the wall shear stress in the gating system. A special attention should be made in choosing refractory at the center stone, the horizontal runner near center stone and the vertical runner at the elbow. This is where the wall shear stress values are highest or where the exposure times are long. / QC 20120203

Narrow molecular weight fractions of Poly(ε-caprolactone) were successfully obtained using the successive precipitation fractionation technique with toluene/n-heptane as a solvent/nonsolvent pair. Calorimetric studies of the melting behavior of fractions that were crystallized either isothermally or under constant cooling rate conditions suggested that the isothermal crystallization of the samples should be used for a proper evaluation of the molecular weight dependence of the observed melting temperature and degree of crystallinity in PCL. The molecular weight and temperature dependence of the spherulitic growth rate of fractions was studied in the context of the Lauritzen-Hoffman two-phase model and the Strobl three-phase model of polymer crystallization. The zero-growth rate temperatures, determined from spherulitic growth rates using four different methods, are consistent with each other and increase with chain length. The concomitant increase in the apparent secondary nucleation constant was attributed to two factors. First, for longer chains there is an increase in the probability that crystalline stems belong to loose chain-folds, hence, an increase in fold surface free energy. It is speculated that the increase in loose folding and resulting decrease in crystallinity with increasing chain length are associated with the ester group registration requirement in PCL crystals. The second contribution to the apparent nucleation constant arises from chain friction associated with segmental transport across the melt/crystal interface. These factors were responsible for the much stronger chain length dependence of spherulitic growth rates at fixed undercooling observed here with PCL than previously reported for PE and PEO. In the case of PCL, the scaling exponent associated with the chain length dependence of spherulitic growth rates exceeds the upper theoretical bound of 2 predicted from the Brochard-DeGennes chain pullout model. Observation that zero-growth and equilibrium melting temperature values are identical with each other within the uncertainty of their determinations casts serious doubt on the validity of Strobl three-phase model. A novel method is proposed to determine the Porod constant necessary to extrapolate the small angle X-ray scattering intensity data to large scattering vectors. The one-dimensional correlation function determined using this Porod constant yielded the values of lamellar crystal thickness, which were similar to these estimated using the Hosemann-Bagchi Paracrystalline Lattice model. The temperature dependence of the lamellar crystal thickness was consistent with both LH and the Strobl model of polymer crystallization. However, in contrast to the predictions of Strobl’s model, the value of the mesomorph-to-crystal equilibrium transition temperature was very close to the zero-growth temperature. Moreover, the lateral block sizes (obtained using wide angle X-ray diffraction) and the lamellar thicknesses were not found to be controlled by the mesomorph-to-crystal equilibrium transition temperature. Hence, we concluded that the crystallization of PCL is not mediated by a mesophase. Metallocene-catalyzed linear low-density (m-LLDPE with 3.4 mol% 1-octene) and conventional low-density (LDPE) polyethylene blends of different compositions were investigated for their melt-state miscibility and concurrent crystallization tendency. Differential scanning calorimetric studies and morphological studies using atomic force microscopy confirm that these blends are miscible in the melt-state for all compositions. LDPE chains are found to crystallize concurrently with m-LLDPE chains during cooling in the m-LLDPE crystallization temperature range. While the extent of concurrent crystallization was found to be optimal in blends with highest m-LLDPE content studied, strong evidence was uncovered for the existence of a saturation effect in the concurrent crystallization behavior. This observation leads us to suggest that co-crystallization, rather than mere concurrent crystallization, of LDPE with m-LLDPE can indeed take place. Matching of the respective sequence length distributions in LDPE and m-LLDPE is suggested to control the extent of co-crystallization. / Ph. D.

The use of degradable biomedical materials has during the past decades indeed modernized medical science, finding applications in e.g. tissue engineering and drug delivery. The key question is to adapt the material with respect to mechanical properties, surface characteristics and degradation profile to suit the specific application. Degradation products are generally considered non-toxic and they are excreted from the human body. However, large amounts of hydroxy acids may induce a pH decrease and a subsequent inflammatory response at the implantation site. In this study, macromolecular design and a combination of cross-linking and adjusted hydrophilicity are utilized as tools to control and tailor degradation rate and subsequent release of degradation products from biomedical polyester-ethers. A series of different homo- and copolymers of -caprolactone (CL) and 1,5-dioxepan-2-one (DXO) were synthesized and their hydrolytic degradation was monitored in phosphate buffer solution at pH 7.4 and 37 °C for up to 546 days. The various materials comprised linear DXO/CL triblock and multiblock copolymers, PCL linear homopolymer and porous structure, and random cross-linked homo- and copolymers of CL/DXO using 2,2’-bis-(ε-caprolactone-4-yl) propane (BCP) as a cross-linking agent. The results showed that macromolecular engineering and controlled hydrophilicity of cross-linked networks were useful implements for customizing the release rate of acidic degradation products in order to prevent the formation of local acidic environments and thereby reduce the risk of inflammatory responses in the body. / QC 20101109

The use of synthetic materials for tissue and organ reconstruction, i. e. tissue engineering, has become a promising alternative to current surgical therapies and may overcome the shortcomings of the methods in use today. The challenge is in the design and reproducible fabrication of biocompatible and bioresorbable polymers, with suitable surface chemistry, desirable mechanical properties, and the wanted degradation profile. These material properties can be achieved in various manners, including the synthesis of homo- and copolymers along with linear and star-shaped architectures. In many applications the materials’ three-dimensional structure is almost as important as its composition and porous scaffolds with high porosity and interconnected pores that facilitate the in-growth of cells and transportation of nutrients and metabolic waste is desired. In this work linear and star-shaped polymers have been synthesized by ring-opening polymerization using a stannous-based catalyst and a spirocyclic tin initiator. A series of linear copolymers with various combinations of 1,5-dioxepane-2-one (DXO), Llactide (LLA) and ε-caprolactone (CL) have been polymerized using stannous octoate as catalyst. It is shown that the composition of the polymers can be chosen in such a manner that the materials’ mechanical and thermal properties can be predetermined. A solvent-casting and particulate leaching scaffold preparation technique has been developed and used to create three-dimensional structures with interconnected pores. The achieved physical properties of these materials’ should facilitate their use in both soft and hard tissue regeneration. Well defined star-shaped polyesters have been synthesized using a spirocyclic tin initiator where L-lactide was chosen as a model system for the investigation of the polymerization kinetics. Neither the temperature nor the solvent affects the molecular weight or the molecular weight distribution of the star-shaped polymers, which all show a molecular weight distribution below 1.19 and a molecular weight determined by the initial monomer-to-initiator concentration. / QC 20101217

The isothermal crystallization and melting temperatures of poly(ε-caprolactone) were correlated using fast differential scanning calorimetry. The melting kinetics was found to be independent of isothermal crystallization temperature and time. The conventional Hoffman-Weeks method could not be used to determine the equilibrium melting temperature because the observed melting temperatures were greater than the crystallization temperatures by a constant, so the Gibbs-Thomson method was used instead, yielding an equilibrium melting temperature of 103.4 ± 2.3°C. A modification was proposed to the non-linear Hoffman-Weeks equation that included a non-linear undercooling dependence for the kinetic fold surface free energy upon crystallization and permitted accurate modeling of the observed melting behavior. The isothermal crystallization rates of four narrow molecular weight poly(ethylene oxide) fractions were characterized using fast differential scanning calorimetry for crystallization temperatures spanning 100°C range with the lower limit approaching the glass transition. A transition from homogeneous to heterogeneous primary nucleation was observed at −5°C. The kinetic analysis suggested that the crystal growth geometry depends strongly on temperature, where rod-like structures begin to appear near the glass transition temperature, highly branched solid sheaves grow throughout the homogeneous primary nucleation temperature range, and spherulites grow in the heterogenous primary nucleation range. Poly(δ-valerolactone) was synthesized using microwave-assisted techniques. Narrow molecular weight fractions were obtained using successive precipitation fractionation. Preliminary isothermal crystallization studies suggest that conventional thermal analysis methods are not adequate to measure the melting temperatures accurately due to reorganization during heating. / Doctor of Philosophy / Plastics may be classified into two general categories: those which form ordered domains upon solidification, i.e. undergo crystallization, and those which remain disordered upon solidification, i.e. form glasses. This work is focused on studying the crystallization and melting processes in two linear polymers, poly(ε-caprolactone) and poly(ethylene oxide), using new experimental technology. In the case of poly(ε-caprolactone), the experimental data could not be rationalized by existing theories, and we have proposed modifications to these theories that explained the results. In the case of poly(ethylene oxide), the application of new experimental technology resulted in previously unreported data that indicated novel behavior at very low crystallization temperatures. In the last portion of this work, poly(δ-valerolactone) was made using a novel approach. Conventional experimental approaches to measuring the crystallization and melting behavior were shown to be inadequate.