Orientador: Antonio Carlos Bannwart / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica, Instituto de Geociencias / Made available in DSpace on 2018-08-14T16:09:37Z (GMT). No. of bitstreams: 1 Lima_IvanNovilleRochaCorrea_M.pdf: 2854489 bytes, checksum: fec392ec12651861ca4547ea5ce279c9 (MD5) Previous issue date: 2009 / Resumo: O presente trabalho tem por objetivo central a medição experimental do coeficiente de transferência de calor bifásico no padrão gás-líquido horizontal intermitente, por ser este um padrão muito comum nas operações de produção de petróleo. Para alcançar esse objetivo, foi construído um aparato experimental consistindo de uma seção de testes alimentada por uma mistura pré-aquecida de ar e água, a diferentes pares de vazões e temperaturas de entrada. Para realizar a troca térmica, o tubo foi circundado por uma jaqueta de água gelada submetida a diversas vazões e temperaturas de entrada, formando, com o tubo central, uma seção de troca térmica de correntes paralelas. A metodologia experimental consistiu em medir a taxa de transferência de calor do fluido interno para o fluido externo e, a partir da diferença média de temperatura entre o fluido quente e a parede, determinar o coeficiente de transferência de calor entre o fluido quente e a parede, para cada elenco de condições de operação. O procedimento foi realizado tanto para os ensaios em escoamento monofásico como para o escoamento bifásico. Os resultados para o coeficiente de transferência de calor do fluido quente foram comparados às correlações e aos modelos existentes e apresentaram resultados satisfatórios. / Abstract: The main objective of the present work is the experimental measurement of the two-phase heat transfer coefficient in the intermittent horizontal gas-liquid flow pattern. This flow pattern is very common in oil production pipelines. In order to reach this objective, an experimental apparatus was built, consisting of a test section fed with an air-water mixture pre-heated at different pairs of inlet flow rates and temperatures. In order to realize the heat transfer, the pipe was surrounded by a jacket containing cold water under various inlet flow rates and temperatures, forming with the central pipe a heat transfer section of parallel current. The experimental methodology consisted of measuring the heat transfer rate from the internal to the external fluid, and from the average difference of the temperature between the hot fluid and the pipe wall, determine the heat transfer coefficient between the hot fluid and the pipe wall for each cast of operating condition. The procedure was carried through for both single phase and two-phase tests. The results of the heat transfer coefficients between the hot fluid were compared with some correlations and existing models and presented satisfactory results. / Mestrado / Explotação / Mestre em Ciências e Engenharia de Petróleo

A pesquisa realizada tratou do estudo da transferência de calor e do fluxo crítico durante a ebulição convectiva no interior de canais de diâmetro reduzidos a partir de dados levantados em bancadas experimentais construídas para esta finalidade. Extensa pesquisa bibliográfica foi efetuada e os principais métodos disponíveis para previsão de coeficiente de transferência de calor, fluxo crítico e mapas de escoamento foram levantados. Os resultados obtidos foram parametricamente analisados e comparados com os métodos da literatura. Pela primeira vez para microcanais, resultados experimentais foram levantados por um mesmo autor em laboratórios distintos buscando verificar a tendência e comportamentos. Tal comparação tem sua importância destacada em face das elevadas discrepâncias observadas na literatura quando resultados de autores distintos, obtidos em condições similares, são comparados. Os resultados levantados foram utilizados na elaboração de modelos que consideram os padrões de escoamento observados em microcanais. A incorporação dos padrões permitiu o desenvolvimento de modelos mecanísticos para coeficiente de transferência de calor, fluxo crítico e critérios para a caracterização da transição entre macro e microcanais baseados na formação do padrão de escoamento estratificado e na simetria do filme líquido no escoamento anular. / This research comprises an experimental and theoretical study on flow boiling heat transfer and critical heat flux inside small diameter tubes based on data obtained in experimental facilities specially designed for this purpose. A broad literature review was carried out and the main methods to predict the heat transfer coefficient, critical heat flux and flow patterns were pointed out. The experimental results were parametrically analyzed and compared against the predictive methods from literature. For the first time, microchannels experimental results obtained by an unique researcher in distinct laboratories were compared and a reasonable agreement was observed. The importance of such a comparison is high-lighted for flow boiling inside microchannels due to the high discrepancies ob-served when results from independent laboratories obtained under similar experimental conditions are compared. Moreover, the experimental results obtained in the present study were used to develop correlations and models for the heat transfer coefficient and heat flux that takes into account the flow patterns observed in microchannels. The heat transfer coefficient and critical heat flux models were developed based on mechanistic approach. In addition, criteria to characterize macro to microchannel transition were proposed based in the occurrence of the stratified flow pattern and the liquid film symmetry under annular flow conditions.

A têmpera dos aços envolve a austenitização de uma peça seguida por um resfriamento rápido para promover a formação de microestrutura martensítica. É necessário avaliar os meios de têmpera para manter o processo de têmpera sob controle. Os parâmetros mais importantes no processo de resfriamento são o coeficiente de transferência de calor e/ou o fluxo de calor entre o meio de têmpera e a peça a ser resfriada. Um dos métodos de se avaliar os meios de têmpera (meios de resfriamento) e saber o que está acontecendo dentro da peça durante o resfriamento do ponto de vista térmico é o problema inverso de condução de calor. O problema inverso de condução de calor consiste na determinação de parâmetros como fluxo de calor, taxa de resfriamento e temperatura em qualquer posição através da peça, assim como o coeficiente de transferência de calor. Esses parâmetros são obtidos a partir de medições de temperatura em um ou mais pontos dentro da peça. O escopo deste trabalho foi desenvolver um software baseado no problema inverso condução de calor para avaliar meios de resfriamento para têmpera. A validação deste código foi feita usando água, óleo de soja, óleo mineral e solução aquosa de NaNO3. / Steels quenching involves part austenitization followed by a fast cooling to promote martensitic microstructure formation. It is necessary to evaluate quenchants in order to keep the quenching process under control. The most important cooling process parameters are the heat transfer coefficient and/or the heat flux between the quenchant and the part to be cooled. One of the methods to evaluate quenchants (cooling media) and to know what is happening inside the part during the cooling in the thermal point of view is the inverse heat conduction problem. The inverse heat conduction problem consists in the determination of parameters like heat flux, cooling rate and temperature in any position across the part, as well as the heat transfer coefficient. These parameters are obtained from temperature measurements in one or more points inside the part. The scope of this work was to develop a software based in the inverse heat conduction problem in order to evaluate quenchants for quenching. The validation of this code was made using water, soybean oil, mineral oil and NaNO3 aqueous solution.

Cette thèse, financée dans le cadre du projet européen CSP2, porte sur l'étude d'un nouveau type de récepteur solaire thermique à concentration utilisant comme fluide caloporteur une suspension dense de fines particules en circulation ascendante dans des tubes verticaux. Ladite suspension est obtenue par fluidisation de particules de classe A. Le principe consiste à créer un écoulement ascendant de la suspension dans un tube vertical exposé au rayonnement solaire concentré qui chauffe la paroi du tube, qui transmet ensuite cette chaleur aux particules, qui la transportent jusqu'à un cycle de conversion d'énergie pour la production d'électricité. Au contraire des fluides solaires classiques, les particules peuvent atteindre les hautes températures (> 700 °C) permettant l'utilisation de cycles à haut rendement de conversion (Brayton, cycles combinés), tout en permettant un stockage direct de la pour une production continue. Au cours de la thèse, un récepteur à un tube a été testé avec succès au grand four solaire du laboratoire PROMES-CNRS à Odeillo, les particules en sortie atteignant 750 °C, ce qui a prouvé la faisabilité du concept et permis la détermination des premières valeurs de coefficient d'échange de chaleur tube-suspension. L'hydrodynamique de l'écoulement et les mécanismes d'échange de chaleur ont été observés grâce à des simulations numériques 3D. Un récepteur de 150 kWth à 16 tubes a ensuite été testé et modélisé, validant l'utilisation du procédé à plus grande échelle. / This thesis, financed in the frame of the CSP2 European project, concerns the study of a new kind of thermal concentrating solar receiver using a dense suspension of solid particles circulating upward in vertical tubes. The suspension is obtained by fluidizing Geldart A-type particles. The principle consists in creating an upward flow of the suspension in a vertical tube exposed to the concentrated solar radiation that heats the tube wall. The heat is then transmitted to the particles circulating inside that transport it to a conversion cycle for electricity production. Contrarily to usual solar heat transfer fluids, particles can reach high temperatures (> 700 °C) that permit to power high efficiency thermodynamic cycles such as Brayton or combined cycles. Moreover they can be used as a direct heat storage medium for continuous electricity production. During this thesis, a one-tube solar receiver was successfully tested at the PROMES-CNRS solar furnace in Odeillo, with particle outlet temperatures of 750 °C reached. The first values of wall-to-suspension heat transfer coefficient were calculated and a Nusselt correlation was determined. A specific flow pattern with a particle downward flux close to the wall and upward flux in the tube center was underlined. The flow hydrodynamics and the heat transfer mechanisms were studied thanks to 3D numerical simulations. A 16-tube 150 kWth receiver was finally tested and modeled, proving the process applicability at larger scale.

No presente trabalho são relatados os resultados obtidos por meio de ensaios de caracterização para os diferentes tipos de óleos vegetais (algodão, canola, girassol, milho e soja), no estado novo e puro, tais como viscosidade, número de acidez, índice de iodo, índice de saponificação, cromatografia gasosa, curvas de resfriamento e coeficiente de transferência de calor. Esses mesmos ensaios foram realizados também com as amostras de óleo de soja com diferentes concentrações de aditivos antioxidantes. As diferentes formulações feitas com óleo de soja foram submetidas a um processo de envelhecimento acelerado (durante 72 horas), suas propriedades foram comparadas com as de dois óleos minerais utilizados para têmpera. O mesmo foi feito para os óleos vegetais, estes porém foram envelhecidos durante 48 horas. Pode-se então, comparar qual amostra sofreu menor oxidação durante um mesmo tempo de envelhecimento e, desta maneira, avaliar qual aditivo antioxidante obteve melhor desempenho, retardando o processo de oxidação no óleo de soja. Esses estudos também permitiram verificar qual, dentre os óleos vegetais, possui as melhores propriedades para ser utilizado no tratamento térmico de têmpera. Amostras do aço AISI 4140 foram temperadas nos diferentes óleos estudados, obteve-se a curva de dureza e as micrografias óticas para cada amostra temperada. / In this work, the results obtained from the characterization of different vegetable oils (cotton, canola, sunflower, corn and soybean) are reported. The oils were evaluated at \"new condition\" and \"pure\" by viscosity, acid and iodine number, saponification, gas chromatography, cooling curves and heat transfer coefficient. These same analyses were also performed on samples of soybean oil containing various concentrations of antioxidant. The various formulations prepared with soybean oil were accelerated aged for 72 hours and their properties were compared with two mineral oils used for quenching. Likewise, the vegetable oils were aged for 48 hours long. Therefore, it was possible to identify which sample exhibited the lower oxidation process at the same aging time and, thus, evaluate the antioxidant additive that promoted the improved oxidation performance for soybean oil. Also, these studies allowed verifying which of the vegetable oils had the best properties to be used as quenchants. Samples of AISI 4140 steel were quenched in different oils and the hardness curve and optical microscopy for each sample were obtained.

The diploma thesis is elaborate in order to evaluate the economic returns of each proposed building insulation options for seniors in Šternberk. For the calculation use to secluded brick apartment building in the street Žitná. The theoretical section describes the types of buildings according to heating demand and a list of different variants of thermal insulation materials. The second part contains suggestions for building insulation in several variants. It worked certificate of energy performance of buildings, costs of proposed options and the costs of operating the apartment building before and after the insulation. Based on the comparison of results is elaborate economic returns for each of the proposed options.

This diploma thesis is focused on measurement of thermal properties of clothes by thermal manikin and on application of results for prediction of thermal comfort in system iHVAC. First part of thesis is dedicated to research with relation to this topic and to definitions of main computational equations necessary for experimental measurement. The choise of method for measurement based on available standards is an important part of this thesis. The main focus of thesis lies on measuring 5 combinations of clothes at different calibration temperatures and same temperature of manikin surface. Then data are examined and also the analysis of uncertaities and repeatability is maked. According to assupmtion , the independence of value of heat transfer coefficient to ambient temperature is comfirmed and calculated heat resistance of every single clothes is compared to existing wardrobe for system iHVAC. The outcome of this thesis is specificied and completed virtual wardrobe which serves to prediction of thermal comfort in car.

This diploma thesis describes possibilities of thermal insulation of a detached house and choice optimization of insulating materials especially based on economic and ecologic factors. The thesis describes basic physical effects that are associated with heat transfer and that should be respected in insulation design. These effects influence the choice of suitable insulating materials based on their properties.

The main aim of this thesis is the model design and control the secondary circuit block VVER 440. The search part of my work is a description of the secondary circuit. In the first part of the calculation is performed for the rated secondary circuit. The second calculation part focuses on the calculation circuit of the secondary for the reduced, influenced by shutting down one steam generator.

This thesis deals with the influence of the oxide layer on the spray cooling of steel surfaces. As part of the work steel samples with oxide layer are made and the thickness, porosity and surface roughness of this layer are characterized. The average thermal conductivity of porous oxide layer is determined for different regimes of oxidation. Further, the influence of the oxide layer on the heat transfer coefficient during the spray cooling is experimentally investigated on created samples and the basic numerical simulation of the cooling is done for selected experiment with oxide layer. The thesis also contains theoretical introduction to given issue.