Tato disertační práce pojednává o plazmonických anténách. Rezonanční vlastnosti plazmonických antén jsou studovány teoreticky i experimentálně. Teoretické výpočty jsou prováděny v programu Lumerical FDTD Solutions užitím numerické metody konečných diferencí v časové doméně. Pro experimentální studium byly antény vyrobeny pomocí elektronové litografie. Rezonanční vlastnosti vyrobených antén jsou studovány fourierovskou infračervenou spektroskopií. Práce se zaměřuje na studium rezonančních vlastností antén vyrobených na vrstvě nanokrystalického diamantu. Dále zkoumá možnost využití antén jako plazmonického senzoru funkcionalizovaného k detekci streptavidinu. Nakonec je představena anténa tvaru písmene V, u které dochází v důsledku porušení symetrie antény ke směrovému rozptylu dopadajícího světla. Tato směrovost se ovšem projevuje jen na vlnových délkách blízkých kvadrupólovému módu antény.

No description available.

Amorphous ribbons of alloy composition Fe75B10Si15 are cast by melt spinning and annealed to partially nanocrystalline states. The magnetic properties are investigated by VSM and MTGA. Structure is examined using XRD and SEM. Results obtained show nanostructured material with excellent soft magnetism in samples annealed at temperatures below the crystallization temperature as well as enhancement of magnetic hardness for annealing at high temperatures. This validates Herzer’s Random Anisotropy model of magnetism in nanostructured materials and provides basis for further inquiry into tweaking alloy compositions and/or manipulating annealing parameters. Also, increase of Curie temperature is noted with respect to increasing annealing temperatures arising from stress relaxation, validating a study on the relationship between the two.

No description available.

No description available.

Crack propagation studies in nanocrystalline alpha-iron samples with grain sizes ranging from 6 to 12 nm are reported at temperatures ranging from 100K to 600K using atomistic simulations. For all grain sizes, a combination of intragranular and intergranular fracture is observed. Mechanisms such as grain boundary accommodation, grain boundary triple junction, grain nucleation and grain rotation are observed to dictate the plastic deformation energy release. Intergranular fracture is shown to proceed by the coalescence of nanovoids formed at the grain boundaries ahead of the crack. The simulations also show that at an atomistic scale the fracture resistance and plastic deformation energy release mechanisms increase with increasing temperature. Finally a softening of the material occurs with decreasing grain size. The elastic properties are found to decrease and the fracture resistance to increase with decreasing grain size. / Master of Science

Ball milling has been shown to produce nanostructures in metal powders through severe repetitive deformation. Ball milling at cryogenic temperatures (cryomilling) is more effective in this capacity due to the low temperature by slowing recovery and minimizing diffusion distances between different components. Nanostructured metals are of interest because of their unique physical and mechanical properties. The result of cryomilling is powder consisting of crystallites on the order of 30 – 50 nm. In order to characterize the properties of this material, it is often necessary to consolidate the powder, which is often difficult without causing significant grain growth. In this work, aluminum-rich and magnesium-rich alloys of varying composition are produced by cryomilling and characterized by x-ray diffraction. A novel consolidation process called high shear powder consolidation (HSPC) is used to densify as-received and as-milled powders with minimal growth. The construction of a cryomill, along with a modification for improving process yield, has provided a platform for the study of nanocrystalline metals. It has been shown that bulk nanocrystalline materials are attainable and that alloy composition influences mechanical properties. / Master of Science

Yes / The tribological performance of a nanocrystalline coating is heavily influenced by its composition, morphology, and microstructural characteristics. This research work describes the effect of heat treatment temperature on the microstructural, morphological, and mechanical behavior of nanocrystalline Ni/TiO2 coatings produced by electrophoresis. The surface morphology and coating cross section were characterized by scanning electron microscopy (SEM). The composition of coatings and the percentage of TiO2 nanoparticles incorporated in the Ni matrix were studied and estimated by using an energy-dispersive spectroscopic (EDS) analysis, while x-ray diffractometry (XRD) was used to investigate the effect of heat treatment temperature on phase structure. The results showed agglomeration of TiO2 nanoparticles on the surface of the coating. The high hardness and wear resistance recorded for the as-deposited coating was attributed to the uniform distribution of TiO2 nanoparticle clusters throughout the cross section of the coating. Heat treatment of the Ni/TiO2 coatings to temperatures above 200 °C led to significant grain growth that changed the surface morphology of the coating and reduced the strengthening effects of the nanoparticles, thus causing a reduction in the hardness and wear resistance of the coatings.

High dielectric constant materials are of technological importance as they lead to the miniaturization of the electronic devices. For instance, in the case of memory devices based on capacitive components, such as static and dynamic random access memories, the dielectric constant will ultimately decide the level of miniaturization. In this context, the observation of anomalously high dielectric constant (>10) in the double perovskite Sr2SbMnO6 (SSM) over wide frequency (100 Hz1 MHz) and (190373 K) temperature range has attracted a great deal of attention. However, unfortunately their dielectric losses were also high which limit their use for possible capacitor and related applications. The dielectric loss however was known to decrease with decreasing crystallite size in electroceramics. Therefore, the present work has been focused on the synthesis of nanocrystalline SSM powders by moltensalt route. The characterization of the ceramics fabricated from these powders for their microstructural and dielectric properties. A cubic phase of SSM powder was obtained by calcining the as synthesized powders at 900°C/10h by using sulphate flux. The crystallite size was ~ 60 nm. The activation energy associated with the particle growth was found to be 95 ± 5 kJmol-1 . The ceramic sintered at 1075°C/16h exhibited high dielectric constant (>10at 1 kHz) with low loss (0.72 at 1 kHz) at room temperature. The results are interpreted in terms of a twolayer model with conducting grains partitioned from each other by poorly conducting grain boundaries. Using this model, we attributed the two electrical responses in impedance and modulus formalisms to the grain and grain boundary effects, respectively, while the detected Debyelike relaxation and large dielectric constant were explained in terms of MaxwellWagner relaxation.

In this thesis, novel bulk Al-based alloys with high content of Al have been produced by powder metallurgy methods from amorphous and partially amorphous materials. Different processing routes, i.e. mechanical alloying of elemental powder mixtures, controlled pulverization of melt-spun glassy ribbons and gas atomization, have been employed for the production of the Al-based powders. Among the different processing routes, gas atomization is the best choice for the production of Al-based amorphous and partially amorphous powders as precursors for the subsequent consolidation step because it allows the production of large quantities of powders with homogeneous properties (e.g. structure and thermal stability) along with a uniform size distribution of particles. Amorphous and nanocrystalline powders have to be consolidated to achieve dense bulk specimens. However, consolidation of these phases is not an easy task and special care has to be taken with respect to accurate control of the consolidation parameters in order to achieve dense bulk specimens without inducing undesirable microstructural transformations (e.g. crystallization and grain coarsening) or insufficient particle bonding. Consequently, the effect of temperature on viscosity as well as on phase formation has been studied in detail in order to select the proper consolidation parameters. Following their characterization, the Al-based powders have been consolidated into bulk specimens by hot pressing (HP), hot extrusion and spark plasma sintering (SPS) and their microstructure and mechanical properties have been extensively investigated. Consolidation into highly-dense bulk samples cannot be achieved without extended crystallization of the glassy precursors. Nevertheless, partial or full crystallization during consolidation leads to remarkable mechanical properties. For example, HP Al84Gd6Ni7Co3 samples display a remarkably high strength of about 1500 MPa, which is three times larger than the conventional high-strength Al-based alloys, along with a limited but distinct plastic deformability (3.5 – 4%). Lower strength (930 MPa) but remarkably larger plastic strain exceeding 25 % has been achieved for the Al87Ni8La5 gas-atomized powders consolidated by SPS above their crystallization temperature. Similarly, HP Al90.4Y4.4Ni4.3Co0.9 bulk samples display high compression strength ranging between 820 and 925 MPa combined with plastic strain in the range 14 – 30%. Finally, preliminary tensile tests for the Al90.4Y4.3Ni4.4Co0.9 alloy reveal promising tensile properties comparable to commercial high-strength Al-based alloys. The mechanical behavior of the consolidated specimens is strictly linked with their microstructure. High strength and reduced plasticity are observed when a residual amorphous phase is present. On the other hand, reduced strength but enhanced plastic deformation is a result of the complete crystallization of the glass and of the formation of a partially or fully interconnected network of deformable fcc Al. These results indicate that the combined devitrification and consolidation of glassy precursors is a particularly suitable method for the production of Al-based materials characterized by high strength combined with considerable plastic strain. Through this method, the mechanical properties of the consolidated samples can be varied within a wide range of strength and ductility depending on the microstructure and the consolidation techniques used. This might open a new route for the development of innovative high-performance Al-based materials for transport applications.