Thesis (MIng)--University of Stellenbosch, 2000. / ENGLISH ABSTRACT: Fouling is readily acknowledged as one of the most critical problems limiting the wider application of membranes in liquid separation processes. A better understanding of fouling layer formation and its monitoring is needed in order to improve on existing cleaning techniques. Plant operation can be optimised if fouling can be monitored by noninvasion means either on the plant itself or on an attached monitoring device. The overall scope of this research was to develop a non-destructive, real-time, in situ visualisation technique or device for concentration polarisation and fouling layer monitoring. Ultrasonic-time-domain-reflectometry (UTDR) was employed as a visualisation technique to provide real-time characterisation of the fouling layer. A 24 cm-long rectangular flat sheet aluminium cell was designed and used as separation device for a desalination system. The experimental results obtained using this module confirmed that there are an excellent correspondence between the flux decline behaviour and the UTDR response from the membrane. The ultrasonic technique could effectively detect fouling layer initiation and growth on the membrane in real-time. In addition to the measurement of fouling, the ultrasonic technique was also successfully employed for monitoring membrane cleaning. Since no real-time permeation data is available during cleaning operations in industrial applications, a UTDR monitoring device may prove to be a very valuable technique in optimising cleaning strategies. The technique was further tested on an 8-inch diameter spiral wrap industrial module and good results were obtained. Stagnant zones, as well as flux flow behaviour inside the module could be determined. However, more research IS needed to fully understand the complex phenomena inside a spiral wrap module. Overall, the UTDR technique and its use in monitoring devices have a major impact in the membrane industry due to its extremely powerful capabilities. / AFRIKAANSE OPSOMMING: Membraan-bevuiling of -verstopping is die grootste struikelblok wat die algemene aanwending van membrane vir verskillende watersuiweringsprosesse negatief beinvloed. 'n Beter begrip van membraan-bevuiling, asook beter metingsmetodes daarvan is nodig om op bestaande skoonmaaktegnieke te verbeter. Die hoofdoel van hierdie studie was die ontwikkeling van 'n nie-destruktiewe-in-lyn visuele tegniek vir die meting van konsentrasie polarisasie en membraan-bevuiling. Deur gebruik te maak van ultrasoniese klank golwe, is 'n tegniek ontwikkel wat 'n direkte visuele aanduiding kon gee van die toestand van membraan-bevuiling binnein die module. 'n Reghoekige aluminium-module, 24 cm lank, is ontwerp en gebou waarbinne die membraan geplaas is vir die skeidingsproses. Resultate dui daarop dat daar 'n uitstekende verband bestaan tussen die afname in permeaatvloei en die ultrasoniese eggo vanaf die membraan. Die ultrasoniese tegniek kon die vorming van en toename in membraan-bevuiling doeltreffend karakteriseer. In teenstelling hiermee, is die tegniek ook suksesvol aangewend om die skoonmaak-proses van membrane te ondersoek. Met min of geen data beskikbaar vir die skoonmaak-proses van membrane in die industriële sektor, het die tegniek enorme potensiaal in die optimisering van bestaande skoonmaak-tegnieke. Die tegniek is verder aangewend op 'n industriële 8-duim deursnee spiraal-module en goeie resultate is verkry. Stagnante sones asook vloed-vloei-patrone binne-in die module kon suksesvol bepaal word. Baie navorsing is egter nog nodig om die ingewikkelde data wat gegenereer word tydens die ondersoek van 'n spiraal-module ten volle te verstaan. Die enorme potensiaal en moontlikhede van die ultrasoniese tegniek kan die begin wees van 'n revolusie in die membraan-industrie.

A structural health monitoring system is desired to monitor the integrity of cylindrical, multi-layer carbon over-wrapped pressure vessels intended to house hydrogen at high pressures. In order to develop the system based on ultrasonic guided wave technology, the interaction between ultrasonic guided waves and defect types of interest must be understood. Finite element models in two and three dimensions are developed to predict guided wave motion in the reservoirs. Key parameters are optimized including frequency range, excited modes, detected modes, and transducer dimensions. A novel baseline subtraction technique in the frequency wavenumber domain is presented to increase lower level detection limits. Some experiments are carried out to corroborate the findings in the finite element environment.

Humpback Chub Gila cypha are endangered cyprinids endemic to the Colorado River drainage and are adapted to live in fast currents of warm, turbid water. Although nine known aggregations of Humpback Chub currently exist in the main-stem Colorado River in the Grand Canyon, little is known about their reproduction. I hypothesized that Colorado River water temperatures below Glen Canyon Dam are too low due to hypolimnetic water releases from Lake Powell for female Humpback Chub to develop mature eggs for spawning. Ultrasonic imaging, also called ultrasound, is an effective, non-lethal method used to determine sex and maturity of a variety of freshwater, anadromous, and marine fishes. However, many previous studies have been performed in laboratory environments. I developed a standardized method for ultrasonically scanning endangered Humpback Chub Gila cypha in remote locations within Grand Canyon, Arizona, USA. This method minimized stress to individual fish and took less than 1 min to perform. I was able to identify female fish with eggs based on two jpeg images and one 10 s video clip collected in the field. I also used ImageJ®, a National Institute of Health image processing program, to develop a brightness index to evaluate the maturity of eggs in female fish. I collected ultrasonic scans of captive, ripe Humpback Chub held at the Southwestern Native Aquatic Resources and Recovery Center (SNARRC) to determine that female fish were potentially ripe when a subsample of their eggs exhibited a brightness value within the 32-44 range. Although I was able to estimate egg maturity, I was not able to estimate egg mass of female fish. I used ultrasound to evaluate reproductive condition of 751 Humpback Chub in Grand Canyon. I documented egg development in female fish from the main-stem Colorado River, Little Colorado River, Havasu Creek, and Shinumo Creek. Egg development in Humpback Chub varies by location and time of year. Potentially ripe (stage 3) female fish were found at all sample locations and dates except at Shinumo Creek in 2013 and 2014. Potentially ripe females were also detected in every main-stem aggregation except for Pumpkin Springs and in two locations outside of established aggregations. Fisheries managers can use ultrasound to collect vital information about the reproductive status of fishes that cannot be killed and that are found in remote or rugged field locations. My findings indicate that female Humpback Chub are able to produce eggs throughout the main-stem Colorado River and that internal egg development and egg production likely do not limit recruitment. However, female fish may never experience the environmental triggers they need to spawn or may not experience conditions that would allow eggs and larvae to survive.

published_or_final_version / Electrical and Electronic Engineering / Master / Master of Philosophy

No description available.

No description available.

The goal of this thesis is to develop more effective quantitative procedures to evaluate the stability of deteriorated metal culverts and a better understanding of the deteriorated culverts' behaviour through non-destructive testing, full scale experiments and numerical analyses. First, three design cases were examined using numerical analysis to study the effects of corrosion, burial depth and staged construction on the capacity of deteriorated steel culverts. Then, a method to measure the remaining wall thickness of two 1.8 m diameter corroded metal culverts using ultrasonic device was developed. Both culverts were then buried in the test pit at Queen's University and tested under nominal and working vehicle loads at 0.9m cover and 0.6m cover. The more heavily corroded structure (CSP1) was tested up to its ultimate limit state, inducing local bending across the crown, as well as local buckling of the remnants of the corrugated steel wall between perforations at the haunches. The results suggest that the single axle pads interact to influence the culvert's behaviour despite the shallow cover used in these experiments. CSP1 was able to carry the working load and did not fail until reaching 340 kN, which was equal to 90% of the fully factored load. The experiment suggests that less deteriorated metal culverts (as compared to CSP1) may have the required capacity. Two finite element packages, CANDE and ABAQUS, were used to perform the numerical investigation and the AASHTO and CHBDC approaches were then used to calculate the thrust force in the culverts. Although the numerical analysis produced conservative values for the thrust forces, it failed to capture the non-linear behaviour of both specimens in the experiments. Both the AASHTO and the CHBDC approaches produced unconservative thrust forces compared to experimental results while numerical analysis using Moore's spreading factor produced the most conservative results in terms of thrust. The analysis suggests that CANDE could be used to predict thrust forces in less deteriorated metal culverts. A procedure to assess the stability of deteriorated corrugated metal culverts based on quantitative data was developed using the numerical analysis and experimental results. / Thesis (Master, Civil Engineering) -- Queen's University, 2013-01-30 12:56:17.945

Bone cutting is widely used in orthopaedic, dental and neuro surgeries and is a technically demanding surgical procedure. Novel surgical methods are continually introduced in orthopaedic, neuro and dental surgeries and are aimed at minimising the invasiveness of the operation and allowing more precise cuts. One such method that utilises cutting with superimposed ultrasonic vibration is known as ultrasonically- assisted cutting (UAC). The main concern in bone cutting is the mechanical and thermal damage to the bone tissue induced by high-speed power tools. Recent technological improvements are concerned with the efforts to decrease the force required by the surgeon when cutting the bone as well as increases in surgery speed. A programme of experiments was conducted to characterise properties of a bone and get a basic understanding of the mechanics of bone cutting. The experiments included: (a) nanonindentation and tension tests to obtain the properties for the finite element (FE) bone cutting model, (b) high-speed filming to observe the chip formation process, which influences thermomechanics of the cutting process in conventional drilling (CD) and ultrasonically-assisted drilling (UAD) and, (c) plane cutting and drilling experiments to measure the levels of force and temperature rise in the bone tissue. Novel two-dimensional finite element (FE) models of cortical bone cutting were developed for conventional and ultrasonically-assisted modes with the MSC.MARC general FE code that provided thorough numerical analysis of thermomechanics of the cutting process. Mechanical properties such as the elastic modulus and strain-rate sensitivity of the bone material were determined experimentally and incorporated into the FE models. The influence of cutting parameters on the levels of stress, penetration force and temperature in the bone material was studied using conventional cutting (CC) and ultrasonically-assisted cutting (UAC). The temperature rise in the bone material near the cutting edge was calculated and the effect of cutting parameters on the level of thermal necrosis was analysed. The necrosis depth in bone was calculated as a distance from the cut surface to the point where the thermal threshold level was attained. Comparative studies were performed for the developed FE models of CC and UAC of bone and the results validated by conducting experiments and using data from scientific publications. The main outcome of the thesis is an in-depth understanding of the bone cutting process, and of its possible application in orthopaedics. Recommendations on further research developments are also suggested.

Dissertation submitted in partial compliance with the requirements for the Master's Degree in Technology: Chiropractic, Durban Institute of Technology, 2005. Thesis (M.Tech.: Chiropractic)-Dept. of Chiropractic, Durban Institute of Technology, 2005 xiv, 99 leaves / Plantar Fasciitis (PF), also called ‘the painful heel syndrome’, is a common cause of heel pain (Barrett and O’Malley, 1999:2200), accounting for between 7% and 10% of all running injuries (Batt and Tanji, 1995:77; Chandler and Kibler, 1993:345). Primarily an overuse injury, resulting from tensile overload, it involves inflammation and micro-tears of the plantar fascia at its insertion on the calcaneus (Lillegard and Rucker, 1993:168; Barrett and O’Malley, 1999:2200). The body’s attempt to heal these micro-tears leads to chronic inflammation and the formation of adhesions (Ambrosius and Kondracki, 1992:30). Transverse friction massage has been found to be beneficial in the treatment of PF (Hyde and Gengenbach, 1997:478,481; Hertling and Kessler, 1996:137). Cyriax (1984) and Prentice (1994) state the effect of frictions to include the breakdown of adhesions (scar tissue), as well as preventing the formation of further adhesions. Graston Technique Instrument-assisted Soft Tissue Mobilisation (GISTM), based on the principles of frictions, aims to break down adhesions, realign collagen fibres and aid in the completion of the inflammatory process (Carey-Loghmani, 2003:31, 51-62; Hammer, 2001). Enabling us to see changes on ultrasonography, which has been found to be an objective, non-invasive way of evaluating PF (Wall and Harkness, 1993:468; Tsai et al, 2000:259; Cardinal et al, 1996:258). These changes include decreased thickness of the fascia. The aim of the study was to see the effect of GISTM on PF in runners, in terms of ultrasonography, and identify any correlation between these findings and other objective and subjective findings. / M

Thesis submitted in full compliance with the requirements for the Masters in Technology Degree: Radiography, Durban University of Technology, 2006. / This study aimed at determining and evaluating the prevalence of gallstones in the Black population of District 28 (D28) in relation to age, gender, diet and body mass index (BMI) in order to identify people at high risk and advise them so that they can avoid the complications and decrease the morbidity rate. Blacks are thought to have increased prevalence of gallstones but there has been no systematic evaluation of its prevalence in D28. METHODS AND MATERIALS 389 Black people from D28 were selected from referrals (for many different radiological examinations) coming to the X-ray and ultrasound departments. Some of the respondents were staff members who also met the selection criteria for the study. An interview was conducted at Ngwelezane hospital using a structured questionnaire on health, social and diet history of the respondents. All information was entered into the data sheet. All respondents were then scanned using Mid-range ultrasound machines to establish the presence of gallstones and this information was thereafter documented on the data sheet. SPSS version 11.5 (SPSS Inc, Chicago, III) was used for data analysis. Prevalence and 95% confidence intervals were calculated using the Epitable module of Epi Info version 6.04 (CDC, 2001). Pearson's Chi square tests were used to assess associations between categorical variables and gall stones. Logistic regression analysis was applied to assess the independent effects of multiple risk factors on the development of gallstones. Backwards elimination method based on likelihood ratios was used with entry and exit probabilities set at 0.05 and 0.1 respectively / M