Conductive polymers, since from their discovery, have become a prominent area of research and found many useful applications in all fields of our daily life. Examples are light emitting diodes, heat generation, chemical sensors and electro-active membranes. Polymer coated textile substrates give flexible and lightweight materials. One well utilized and thoroughly explored conductive polymer is poly(3,4-ethylenedioxythiophene) also known as PEDOT. Although there are different ways to produce PEDOT one of the most common is the VPP technique. The typical procedure when using VPP is to introduce the monomer vapor to an oxidant coated substrate so that it polymerizes on the surface of the substrate. Throughout this study, the VPP technique has been used to produce PEDOT on different textile fibers. Aim was first of all optimizing the process gaining low electric resistance, i. e. high conductivity, of produced coated fibers but also multilayer coatings of fibers. Outcome indicates some parameters not having a clear influence over the results while others had a more distinct impact. A noteworthy result was obtained by coating a substrate, namely lyocell fiber, multiple times with layers deposited directly on each other. This decreased the resistance from 5.1 (± 1.6) kΩ/10 cm to 1.0 (± 0.1) kΩ/10 cm, for one layer and multiple layers respectively. Adding 15 wt. % of the copolymer PEG-PPG-PEG to the oxidant solution decreased the resistance from 6.8 (± 1.2) kΩ/10 cm to 3.9 (± 0.8) kΩ/10 cm. Final conclusion is that among the ways, to improve conductivity for PEDOT coated fibers, applied in this study are best results obtained by multi-layer coating.

Electrochemical copolymerizations of thiophene (Th) and 3,4-ethylenedioxythiophene (EDOT) was performed in this study. Incorporation of Th with EDOT units have accelerated deposition rate in relative to the simple polymerization behavior of EDOT. The electrochemical properties of poly(thiophene-co-3,4-ethylenedioxythiophene) (PTh-EDOT) are different from the homopolymers of polythiophene (PTh) and poly(3,4-ethylenedioxythiophene) (PEDOT). PTh-EDOT were then served as cathode materials of lithium-ion (Li-ion) batteries to test their capability to transfer lithium ion in 1.0 M LiPF6/ethylene carbonate/dimethyl carbonate solution. PTh-EDOT copolymer prepared from the monomer ratio of 1/1 (Th/EDOT) shows better stability than PEDOT and PTh homopolymers, polymer property enhancement by copolymerization is thus demonstrated. A composite electrode material PEDOT/LiCoO2 was prepared from the electrochemical polymerization of EDOT on LiCoO2 electrode was primarily prepared to inspect the influence of PEDOT on the electrochemical features of LiCoO2. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) show the successful deposition of PEDOT over LiCoO2 particles. Compared to the simple LiCoO2 electrode, PEDOT/LiCoO2 composite cathode shows enhanced properties including rate capability and cycle stability for potential Li-ion battery application. Nevertheless, differential scanning calorimetry (DSC) scans on the fully charged cathodes imply that PEDOT may reduce the thermal stability of LiCoO2. Two carbon materials, vapor grown carbon fibers (VGCF) and nano-scaled Ketjen black EC (KB), were implemented into LiCoO2 electrode. The influence of different carbon additive and their content on the performance of LiCoO2 such as rate capability and cycle ability has been evaluated. KB shows more positive effects than VGCF even in the case of a low 1 wt% content. Furthermore, incorporation of PEDOT was made by electrochemical deposition of EDOT on the preformed LiCoO2-VGCF and LiCoO2-KB composite electrodes. The influence of the carbon additives and the conductive PEDOT polymer on LiCoO2 was then investigated. Compared to the electrodes without PEDOT coating, PEDOT-incorporated composite electrodes show larger capacity, better transfer rate of lithium ions in electrolytes, and enhanced cycle ability. The electrochemical deposition of PEDOT on the LiCoO2/nano-carbon cathodes provides a new approach to implement the conducting polymers in Li-ion batteries.

Electrically conductive or electro-active fibers are the key components of smart and interactive textiles, which could be used in medical, sports, energy, and military applications in the near future. The functionalization of high-performance textile yarns/fibers with conjugated polymers can produce conductive fibers with better electro-mechanical properties, which is difficult with commonly used spinning techniques. In this thesis work, textile-based conductive yarns/fibers were prepared by coating viscose and polyester (PET) yarns with the conjugated polymer PEDOT. For coating purposes, an efficient technique called chemical vapor deposition (CVD) was used, which is a solventless technique and can produce PEDOT polymer layers with high conductivity values. The polymerization of EDOT monomer vapors and coating of oxidant (FeCl3 or FepTS) enriched viscose and PET yarns took place simultaneously. The PEDOT-coated viscose and polyester yarns showed relatively high conductivity values, which could be sufficient for many electronic applications. The polymerization process and the quality of PEDOT polymer strongly depends on different reaction conditions. In this research work, the impact of most of these reaction parameters on the electrical, mechanical, and thermal properties of PEDOT-coated conductive yarns was considered separately. Under specific reaction conditions, it was found that viscose fibers were successfully coated with PEDOT polymer and showed rather high electrical conductivity (≥ 15 S/cm). However, due to the acid hydrolysis of viscose fibers in FeCl3 solutions, the mechanical properties were drastically reduced. In order to improve the mechanical properties of conductive yarns, a relatively stable and chemical-resistant substrate (PET) was coated with PEDOT polymer. Comparative studies between PEDOT-coated viscose and PET conductive yarns showed that the electrical and mechanical properties were enhanced by changing the substrate material. Later on, PEDOT-coated conductive fibers were treated with silicone elastomer solution and due to the thin silicone layers, the hydrophobic properties, flexibility, and durability of coated yarns was improved. Furthermore, a novel electrical resistance-measuring setup was developed, which can be used not only for fibers but also for fabric structures. The electrical characterization of PEDOT-coated conductive yarns showed that it can be used effectively for sensitive fibers without damaging their surface morphology. Finally, the use of conductive yarns as stretch sensors was evaluated. For this purpose, small rectangular knitted patches of conductive yarns were prepared and then the change in electrical resistance values at different extension percentages (5–50%) was investigated. The constant variations in electrical resistance values at different extension and relaxation cycles for longer periods of time revealed that the conductive yarns produced have the potential to be used as stretch sensors for monitoring of vital signs in medical and sports applications. / <p>Thesis for the Degree of Doctor of Philosophy to be presented on March 08, 2013, 10.00 in KA-salen, Kemigården 4, Chalmers University of Technology, Gothenburg</p>

Poly(3,4-ethylendioxythiophen) (PEDOT) ist ein Kunststoff der zur Gruppe der intrinsisch leitfähigen Polymere (ILP) zählt. Aufgrund seiner chemischen und thermischen Stabilität findet er Verwendung in antistatischen Verkleidungen und als Elektrodenmaterial. PEDOT (und andere ILP) zeigen aufgrund ihrer Schaltbarkeit zwischen (reduzierten, ) neutralen und oxidierten Zuständen unterschiedliche Eigenschaften wie Leitfähigkeit, Farbe oder Viskoelastizität. Im Rahmen dieser Arbeit wurden die elektrochemischen und viskoelastischen Eigenschaften von PEDOT-Filmen untersucht. Dabei wurde die Quarzmikrowaage (QCM) in Verbindung mit potentiostatischen (Potentialsprung, PS) und potentiodynamischen (Cyclovoltammetrie, CV) elektrochemischen Methoden verwendet, so dass in situ elektrochemische und mechanische Eigenschaften der Filme zugänglich waren. Zur Bestimmung der viskoelastischen Eigenschaften wurde ein Auswertealgorithmus entwickelt, welcher auf ein mathematisches Modell zur Bestimmung des Schermoduls nach Efimov zurückgreift. Während der Herstellung wurden Parameter wie Lösungsmittel, Leitsalz, Vorpolarisations- und Abscheidungspotential variiert und die erhaltenen Filme bezüglich Schermodul und Morphologie charakterisiert. Es konnte gezeigt werden, dass die Elektrolytzusammensetzung einen entscheidenden Einfluss auf die viskoelastischen Eigenschaften der Filme besitzt, welche mit der Morphologie der Filme korrelieren. Des Weiteren wurden die Änderungen der viskoelastischen Eigenschaften dieser Filme untersucht, welche während dem elektronischen Schalten zwischen neutralem und oxidiertem Zustand aufgrund des Ionenaustausches erfolgen. CV- und PS-Experimente zeigten, dass die viskoelastischen Eigenschaften durch Konzentration und pH-Wert des Elektrolyten beeinflusst werden und in unterschiedlicher Weise auf die Potentialänderungen reagieren. Durch den Einbau von Magnetit-Partikeln in die Schichten konnten Hybridfilme erhalten werden, deren Eigenschaften durch das Anlegen eines äußeren Magnetfeldes beeinflusst werden können. Solche Filme zeigten in einem äußeren Magnetfeld (0,7T) höhere Schermodule und einen stark unterdrückten Ionenaustausch.

The subject of the present licentiate thesis is density functional theorybased electronic structure calculations of organic thermoelectric materials and novel organic molecules. We used the Car-Parrinello molecular dynamics method in order to investigate the electronic structure of “green energy” and “greenchemistry” compounds. First, we have investigated the electronic structure of the poly(3,4-ethylene-dioxythiophene) (PEDOT) and its derivatives - the best studied and successfully implemented by industry organic thermoelectric material. Its transparency, low toxicity and high stability in the oxidized state are combined withan ability to produce electrical current when applying a temperature gradient. This makes PEDOT a perfect “organic metal” and a first candidate for organic thermoelectrogenerators - devices that can produce “green energy” from a temperature difference. The average structures found in these quantum dynamical simulations agree well with earlier static electronic structure studies. The energy gap of two, four and six unit oligomers of PEDOT was calculated and was found to lie in the range of previous theoretical studies. We have also calculatedthe point-charge distributions along the polymer backbone in order to investigate the polaron formed by doping agents of PEDOT. Our analysis allowed us to predict possible localization of the charge in the center of the polymer chain. However, further calculations of the twelve unit PEDOT and its selenium and tellurium derivatives will provide more information. First-principles calculations for the tellurium derivative of PEDOT are here presented for the first time. The second part of our investigation concerns theoretical calculations of novel piperidine-containing acetylene glycols. These molecules were newly synthesized by our experimental collaborators and are expected to provideplant growth stimulation properties, the same as its diacetylene analogs. We performed quantum mechanical calculations of four compounds, presented ananalysis of the highest occupied and lowest unoccupied molecular orbitals and collected detailed information on point-charges for further parametrization of novel molecules for future computational studies. According to these results, the low production yield found in the experiments cannot be attributed to chemical instability in these novel compounds. / <p>QC 20150629</p> / ScalTEG SSF

Conductive polymers are also known as "organic metals" due to their semiconducting properties. They are found in a wide range of applications in the field of organic electronics. However, the growing number of experimental works is not widely supported with theoretical calculations. Hence, the field of conductive polymers is experiencing lack of understanding of mechanisms occurring in the polymers. In this PhD thesis, the aim is to increase understanding of conductive polymers by performing theoretical calculations.        The polymers poly(3,4-ethylenedioxythiophene) (PEDOT) together with its selenium (PEDOS) and tellurium (PEDOTe) derivatives, poly(p-phenylene) (PPP) and naphthobischalcogenadiazoles (NXz) were studied. Several computational methods were applied for analysis of mentioned structures, including density functional theory (DFT), tight-binding modelling (TB), and Car-Parrinello molecular dynamics (CPMD) calculations. The combination of CPMD and DFT calculations was applied to investigate the PEDOT, PEDOS and PEDOTe. The polymers were studied using four different functionals in order to investigate the full picture of structural changes, electronic and optical properties. Temperature effects were studied using molecular dynamics simulations. Wide statistics for structural and molecular orbitals analysis were collected.         The TB method was employed for PPP. The formation and motion of the excitations, polarons and bipolarons, along the polymer backbone was investigated in presence of electric and magnetic fields. The influence of non-magnetic and magnetic impurities was determined.        The extended π-conjugated structures of NXz were computed using B3LYP and ωB97XD functionals in combination with the 6-31+G(d) basis set. Here, the structural changes caused by polaron formation were analyzed. The combined analysis of densities of states and absorption spectra was used for understanding of the charge transition. / <p>QC 20170928</p>