This thesis examines converter topologies suitable for Module Integrated Converters (MICs) in grid interactive photovoltaic (PV) systems, and makes a contribution to the development of the MIC topologies based on the two-inductor boost converter, which has received less research interest than other well known converters. The thesis provides a detailed analysis of the resonant two-inductor boost converter in the MIC implementations with intermediate constant DC links. Under variable frequency control, this converter is able to operate with a variable DC gain while maintaining the resonant condition. A similar study is also provided for the resonant two-inductor boost converter with the voltage clamp, which aims to increase the output voltage range while reducing the switch voltage stress. An operating point with minimized power loss can be also established under the fixed load condition. Both the hard-switched and the soft-switched current fed two-inductor boost converters are developed for the MIC implementations with unfolding stages. Nondissipative snubbers and a resonant transition gate drive circuit are respectively employed in the two converters to minimize the power loss. The simulation study of a frequency-changer-based two-inductor boost converter is also provided. This converter features a small non-polarised capacitor in a second phase output to provide the power balance in single phase inverter applications. Four magnetic integration solutions for the two-inductor boost converter have also been presented and they are promising in reducing the converter size and power loss.

This thesis applies digital repetitive control to a single-phase DC-to-AC converter, with some proposed designs to improve stability and enhance performance of the converter under various load variations. A practical DC-to-AC converter is required to convert DC power to stable AC power with low harmonic distortion when attached to various linear or nonlinear loads. This thesis combines repetitive control with feedback dithering modulation and optimal state feedback to control the converter. The repetitive control is responsible for regulating output power and eliminating harmonics, while the feedback dithering modulation for switching the power transistors with reduced switching noise and the state feedback for stabilizing the converter under various load variations. The presented control and modulation schemes of the power converter are implemented on an FPGA (Field Programmable Gate Array). The experiments confirm the excellent performance and robustness of the converter, indicating a total harmonic distortion of less than 0.5% for the converter when attached to various linear or nonlinear loads.

The objective of the proposed research is to investigate feasible approaches to dynamic control of the power grid. Growth in the demand for electric power, and an increase in the penetration of renewable energy resources are causing congestion on an already aging power grid. Conventional grid control involves the use of static assets that operate on long time scales. These assets provide no dynamic control on the grid, and are typically used for scheduled support. Existing solutions (FACTS devices) to dynamic grid control have seen minimal market penetration because of high cost and low reliability. The proposed research provides a solution for dynamic control of the power grid that augments existing grid assets with a thin AC converter (TACC) to realize enhanced dynamic control. The TACC is a direct AC converter with filter elements and no bulk energy storage that dynamically reflects the asset value on the grid. The converter has a fail-normal mode of operation that returns the asset to its initial operating state, thereby not degrading system reliability. Some applications of TACCs include Inverter-Less STATCOMs and Controllable Network Transformers, which are realized by augmenting shunt VAR capacitors and load tap changers respectively. The principle of virtual quadrature sources is proposed to enable conditioning of AC voltages and currents. The concept is a novel method to realize control of phase angle and, or harmonics in single-phase AC converters, with no bulk energy storage. This concept is used to control the TACC and provides the asset with significantly enhanced control capabilities. Scaling of the TACC to utility voltage and power levels has been addressed by proposing a novel multilevel direct AC converter. The concept proposes the use of commercially available low cost semiconductor devices to realize high power converters. The specific application chosen to validate the concept of TACCs, through a medium voltage design, is the Inverter-less STATCOM.

Thesis (MEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: The development of fast and efficient processors, programmable devices and high power semiconductors has led to the increased use of semiconductors directly in the power supply path in order to achieve strict power quality standards. New and advanced algorithms are used in the process and calculated on-line to bring about the required fast response to voltage variations. Losses in high voltage semiconductors increase with increased operating frequencies. A balance between semiconductor power losses and power quality is achieved through control of power semiconductor switching frequencies. A predictive control algorithm to achieve high power quality and limit the power losses in the high power semiconductor switches through switching frequency control is discussed for a tap switched voltage regulator. The quality of power, voltage regulator topology and the control algorithm are discussed. Simulation results of output voltage and current are shown when the control algorithm is used to control the regulator. These results are verified by practical measurements on a synchronous buck converter. / AFRIKAANSE OPSOMMING: Die ontwikkeling van vinnige en doeltreffende verwerkers, programmeerbare toestelle en hoëdrywings halfgeleiers het gelei tot 'n groter gebruik van halfgeleiers direk in die kragtoevoer pad om streng elektriese toevoer kwaliteit standaarde te bereik. Nuwe en gevorderde algoritmes word gebruik in die proses en word aan-lyn bereken om die nodige vinnige reaksie tot spanningswisselinge te gee. Verliese in hoë-spannings halfgeleiers verhoog met hoër skakel frekwensies. 'n Balans tussen die halfgeleier drywingsverliese en spanningskwalteit is behaal deur die skakel frekwensie in ag te neem in die beheer. 'n Voorspellinde-beheer algoritme om ‘n hoë toevoerkwaliteit te bereik en die drywingsverliese in die hoëdrywingshalfgeleier te beperk, deur skakel frekwensie te beheer, is bespreek vir 'n tap-geskakelde spanning reguleerder. Die toevoerkwaliteit, spanningsreguleerder topologie en die beheer algoritme word bespreek. Simulasie resultate van die uittree-spanning en stroom word getoon wanneer die beheer algoritme gebruik word om die omsetter te beheer. Hierdie resultate is deur praktiese metings op 'n sinkrone afkapper.

Submitted by Alex de Sá Martins null (lex.martins@hotmail.com) on 2017-12-16T23:31:27Z No. of bitstreams: 1 ANÁLISE E PROJETO DO CONVERSOR FONTE-Y PARA USO....pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) / Approved for entry into archive by Maria Marlene Zaniboni null (zaniboni@bauru.unesp.br) on 2017-12-18T12:51:16Z (GMT) No. of bitstreams: 1 martins_as_me_bauru.pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) / Made available in DSpace on 2017-12-18T12:51:16Z (GMT). No. of bitstreams: 1 martins_as_me_bauru.pdf: 2723184 bytes, checksum: 9e77f24832992941e605e87a84c25d1a (MD5) Previous issue date: 2017-10-26 / Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) / Este trabalho aborda o estudo de topologia de conversor de energia baseada no uso de configuração de rede de impedância denominada fonte-Y, com o objetivo de ser aplicado em sistemas de geração distribuída de energia, em redes de baixa tensão. Em sistemas de geração distribuída de energia usualmente se faz necessária a existência de um estágio elevador de tensão e um estágio inversor, ambos controlados para produzir tensão e/ou corrente senoidal com mesma frequência, amplitude e fase da rede elétrica. Nesse sentido, este trabalho propõe a aplicação do conversor fonte- Y entre a geração e a conexão com e rede elétrica, de forma que as ações de conversão relacionadas com a elevação (CC-CC) e inversão (CC-CA) sejam efetuadas de forma integrada por uma única estrutura, contribuindo com a possibilidade de melhoria no rendimento global devido à minimização de estágios de conversão em cascata. Inicialmente, é efetuado um levantamento bibliográfico relacionando as principais topologias de conversores utilizando redes de impedância com indutores acoplados, considerando os aspectos operacionais, arranjo de impedância e ganho estático idealizado, desprezando perdas entre tensão de entrada e tensão máxima de saída obtida. Segue-se o estudo da operação de conversor CCCC empregando rede de impedância do tipo Y, definição das equações que regem o comportamento no tempo das tensões e correntes nos capacitores e indutores. É feita uma avaliação comparativa do ganho estático de tensão obtido e dos esforços nos semicondutores em função das variáveis de controle de projeto e operação disponíveis. Prossegue-se com o estudo da operação do conversor CC-CA empregando rede de impedância do tipo Y, considerando extensão das expressões encontradas para a operação como conversor CC-CC. Por fim, simulações computacionais foram desenvolvidas no ambiente PSIM contemplando o emprego dos circuitos e estratégias de modulação relacionadas com aplicações do conversor fonte- Y, em operação CC-CC e operação CC-CA visando a integração em sistemas de geração de energia, para demonstrar as vantagens e desvantagens do uso dessa topologia. / This paper deals with the study of energy converter topology based on the use of impedance network configuration called Y-source, with the objective of being applied in photovoltaic energy cogeneration systems in low voltage grids. In photovoltaic energy generation systems, it is usually necessary to have a voltage boost stage and an inverter stage, both controlled to produce voltage and / or sine current with the same frequency, amplitude and phase of the power grid. In this sense, this work proposes the application of the Y-source converter between the photovoltaic generation and the connection with the electric grid, so that the conversion actions related to elevation (DC-DC) and inversion (DC-AC) in a way integrated by a single structure, contributing to the possibility of improvement in the overall yield due to the minimization of cascade conversion stages. Initially a bibliographical survey was performed relating the main inverter topologies using impedance networks with coupled inductors considering the operational aspects, impedance arrangement and ideal static gain between the input voltage and the maximum output obtained. ext, the study of the DC-DC converter operation using the Y-type impedance network, definition of the equations governing the time behavior of the voltages and currents in the capacitors and inductors, is presented. It is also done the comparative evaluation of the static voltage gain obtained and the stresses in the semiconductors according to the available control and design control variables. Study of the operation of the DC-AC converter employing type Y impedance network, considering the extension of the expressions found for the operation as DC-DC converter. Finally, computational simulations were developed in the PSIM environment, considering the use of circuits and modulation strategies related to Y-source converter applications, in DC-DC operation and DC-AC operation for integration into power cogeneration systems, to demonstrate advantages and disadvantages of using this topology. / 134173/2017-1

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / This thesis proposes a design of a power supply for high-pressure discharge lamps based on a high efficiency and high power factor electronic ballast, without exciting the intrinsic acoustic resonance. The ballast consists on a bipolar buck chopper operating in continuous conduction mode (CCM), with an input filter, and an igniter circuit. It works with a switching frequency of 33 kHz and supplies the lamp in the mains frequency. The igniter circuit provides the necessary high voltage for the lamp's startup initial procedure. It is controlled by an 8 bits microcontroller, thus contributing to reduction in the number of parts and the ballast final cost, without compromising its reliability. Two possible solutions for an igniter circuit are proposed, the first based on a igniter device, and the second on a LC resonant circuit. A study on the ignition process and the required circuits to guarantee it, and a brief review on the electrical characteristics of electromagnetic ballasts are also included as secondary contributions. Experimental results with a 70W HPS lamp supplied by a 220V±20% and 60 Hz mains, are presented to validate the proposed ballast. The behavior of the experimental ballast shows that it is a good choice in avoiding unstable effects provoked by acoustic resonance phenomenon. / Esta dissertação apresenta o projeto de uma fonte de alimentação para lâmpadas de descarga em alta pressão baseada em um reator eletrônico com alto rendimento e ótimo fator de potência que não excita de forma destrutiva a ressonância acústica (AR). O reator consiste de um conversor buck bipolar operando em modo continuo (CCM), com filtro de entrada acoplado e com um circuito de ignição. O conversor opera em 33 kHz e alimenta a lâmpada em freqüência de rede. O circuito de ignição fornece a alta tensão para a formação inicial do arco elétrico. O controle do reator é implementado em um microcontrolador de 8 bits, o que contribui com a redução do número de componentes e do custo final do sistema, sem prejudicar a confiabilidade do mesmo. Duas propostas de circuito de ignição são apresentadas, uma baseada em um dispositivo ignitor, e a segunda em um circuito LC ressonante. Uma breve revisão e avaliação das características elétricas do reator eletromagnético é também apresentada a título de comparação. Um estudo do processo de ignição e os circuitos necessários a formação do arco é também incluído. Resultados experimentais para uma lâmpada HPS de 70W alimentada a partir de uma rede de 220V±20% e 60Hz são apresentados para validar o reator proposto e demonstram que este é uma boa escolha para evitar os efeitos danosos do fenômeno da ressonância acústica.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / This thesis proposes to improve the efficiency of public illumination systems by means of AC chopper based power converters. A comparative study of high performance AC/AC converters feeding high pressure sodium lamps on mains frequency is presented. These converters are obtained using standard DC/DC topologies with bi-directional switches (four quadrants). A high pressure lamp ballast design methodology is also presented, based on the suppositions of high input power factor and without exciting acoustic resonances at destructive levels. The topologies used are the Buck-Boost, Ćuk, SEPIC and ZETA operating on continuous current mode, with or without input filter, and an ignition circuit. The converters' switching frequencies are 33 kHz feeding the lamp at low frequency (mains frequency). The ignition circuit providing the high voltage required to guarantee the initial arc to start-up the lamp, is presented, analyzed and optimized in the thesis. To control the ballast a 32 bits microcontroller is used, contributing to reduce the component count and the overall system cost. The base to propose a new control design methodology and power circuit parts specification is the Brazilian standards and a comparison with the electromagnetic ballasts output waveforms. Experimental results supplying a 70 W HPS lamp, connected to the mains (220 V ±20% e 60 Hz) through the proposed ballasts, are presented in order to validate the thesis. / Este trabalho visa aprimorar os sistemas de iluminação pública aplicando reatores eletrônicos baseados em conversores CA/CA. Apresenta-se um comparativo entre conversores tradicionais CC/CC, aplicando a eles interruptores bidirecionais em tensão e corrente, de modo a alimentar a lâmpada de alta pressão de sódio na frequência da rede de alimentação, formando um conversor estático CA/CA com alto rendimento. Apresenta uma metodologia de projeto para fonte de alimentação de lâmpadas de descarga em alta pressão baseada em reatores eletrônicos com alto rendimento e elevado fator de potência, que não excitam de forma destrutiva a ressonância acústica (AR). O reator consiste dos conversores Buck-Boost, Ćuk, SEPIC e ZETA bipolares operando por modulação de largura de pulso (PWM) em modo de condução de corrente contínua (CCM), com ou sem filtro de entrada acoplado e com um circuito de ignição. O conversor opera em 33 kHz e alimenta a lâmpada na frequência da rede. O circuito de ignição fornece a alta tensão para a formação inicial do arco elétrico e neste trabalho de doutoramento foi equacionado e otimizado quando comparado ao modelo tradicional. O controle do reator é implementado em um microcontrolador de 32 bits, o que contribui com a redução do número de componentes e do custo final do sistema, sem prejudicar a confiabilidade do mesmo. As formas de onda de saída de reatores eletromagnéticos e as normas vigentes servem de base para o dimensionamento dos componentes e a obtenção de uma nova metodologia de controle. Resultados experimentais para uma lâmpada HPS de 70 W alimentada a partir de uma rede de 220 V ±20% e 60 Hz são apresentados para validar os reatores propostos.

Este trabalho, constitui-se em uma contribuição para o estudo das estratégias de mo-dulação direta baseadas em histerese e que funcionam em frequência fixa de comutação. Tem como objetivo principal propor a estratégia delta modificada, que diferencia-se na forma de ajuste da largura de banda de histerese, alterando-se seus limites e em como executa o comando de bloqueio das chaves de potência, para que a corrente de saída se mantenha em frequência fixa de operação e apresente rápida resposta dinâmica no sistema controlado. Para tanto, não necessita da utilização de derivadas, nem de uma corrente média de referência, tão pouco, se utiliza dos tempos de comutação. A estratégia proposta, comprova que é possível produzir os adequados pulsos de comando para o processamento da energia proveniente de célula combustível, através do conversor estático de potência, utilizando-se, principalmente, dos valores de ultrapassagem nos limites estabelecidos de histerese. Como objetivo secundário desta pesquisa, desenvolve-se um conversor CC/CC auxiliar para adaptar e estabilizar a energia proveniente da CAC, compondo-se um sistema útil que serve de base para fornecer energia, aos mais diversos tipos de cargas em CC. Além disso, apresenta-se uma revisão das estratégias de modulação em modo direto para o controle da corrente de saída no conversor estático, tendo como base a tensão nos terminais de um indutor. Contudo, outras estratégias são naturalmente citadas, no transcorrer deste trabalho, devido haver combinações entre as diferentes estratégias moduladoras e controladoras comentadas. / This work, is a contribution to the study of direct modulation strategies based on hysteresis and that operate at fixed switching frequency. Its main objective is to propose the modified delta strategy, which differentiates from the others strategies in the form of adjustment of hysteresis bandwidth, changing its limits and in executing the locking command of the power keys, so that the output current is maintain at fixed frequency of operation and a rapid dynamic response in the controlled system. In order to do so, it does not require the use of derivatives or a reference average current and also the switching times are not used. This strategy shows that it is possible to produce the appropriate command pulses for the processing of fuel cell energy by the static power converter using mainly the exceedance limit values. As a secondary objective of this research, an auxiliary DC/DC converter is developed to adapt and stabilize the energy coming from the fuel cell, forming a useful system that serves as a base to supply power to the most diverse types of DC loads. In addition, we present a review of the direct-mode modulation strategies for the control of the output current in the static converter, updating data, and based on the voltage at the terminals of an inductor; how-ever, others strategies are naturally cited because there are combinations between the different modulating strategies and controllers commented on in the course of this work.

The Diploma thesis deals with control of three-phase active rectifier and a three-phase DC/AC converter. It also explains phase-locked loop principle. The theoretical part including first three chapters lists several control approaches to three phase active rectifier and three phase DC/AC converter. Described control approaches to the active rectifier are control in dq frame and control in dq UVW frame. Listed control approaches to the DC/AC converter include cascaded control structure and a full state feedback control. The practical part is divided into last three chapters and includes mathematical description of phase-locked loop principle, model of active rectifier controlled in dq frame and a model of DC/AC converter controlled both by a cascaded control and a full¬ state feedback. The models are created in Matlab Simulink.

The topic of this diploma thesis is a traction drive of electrocar with fuel cell. The drive is supplied with hydrogen fuel cell with power of 2 kW. The traction drive consists of the three-phase DC/AC converter and the asynchronous machine. The main part of this work is a creation of the mathematical model of the traction drive in program Matlab–Simulink.