Master of Science / Department of Architectural Engineering / Don Phillippi / Concrete anchors represent an important transition for both the design and construction of a project. Anchors are produced in two main categories: cast-in-place and post-installed. For designers, anchors are used to attach steel members to supporting concrete members. The anchors are designed using the provisions outlined in Building Code Requirements for Structural Concrete, ACI 318-11, Appendix D. These anchors are used to transmit tension and shear forces by using an individual anchor or a multiple anchor group. For contractors, anchor installation marks the transition between concrete and steel construction. Various types of anchors are produced by manufacturers, requiring contractors to be familiar with many installation methods. Careful planning and coordination is necessary to layout and place anchors into their correct location. Once anchors are installed, they must be protected from damage resulting from moving machinery and material. The purpose of this report is to introduce the basics to design concrete anchors by outlining the provisions in ACI 318-11 Appendix D and demonstrating these provisions with design examples. Anchor types, applications and common construction issues important to the structural engineer are also discussed.

A numerical technique based on the theory of plasticity is developed to predict an optimum failure surface generatrix and concrete breakout capacity of single anchors away from edges under tensile loads. Concrete is regarded as a rigid, perfectly plastic material obeying a modified coulomb failure criteria with effective compressive and tensile strengths. The failure mode is idealized as an assemblage of two rigid blocks separated by failure surfaces of displacement discontinuity. Minimization of the collapse load predicted by the energy equation produces the optimum shape of the failure surface generatrix. A simplified solution is also developed by approximating the failure surface as two straight lines. The effect of different parameters on the concrete breakout capacity of anchors is reviewed using the developed mechanism analysis, ACI 318-05, and test results of 501 cast-in-place and 442 post-installed anchor specimens. The shape of failure surface and concrete breakout capacity of anchors predicted by the mechanism analysis are significantly affected by the ratio between effective tensile and compressive strengths of concrete. For anchors installed in concrete having a low ratio between effective tensile and compressive strengths, a much larger horizontal extent of failure planes in concrete surface is predicted by the mechanism analysis than recommended by ACI 318-05, similar to test results. Experimental concrete breakout capacity of anchors is closer to the prediction obtained from the mechanism analysis than ACI 318-05. ACI 318-05 provisions for anchors sharply underestimate the breakout capacity of cast-in-place and post-installed anchors having effective embedment depths exceeding 200 and 80 mm (7.87 to 3.15 in.), respectively, installed in concrete of compressive strength larger than 50 MPa (7250 psi).

Yes / The validity of the modification factor specified in the ACI 318-11 shear provision for concrete members to account for the reduced frictional properties along crack interfaces is examined using a comprehensive database comprised of 1716 normalweight concrete (NWC) beam specimens, 73 all-lightweight concrete (ALWC) beam specimens, and 54 sand-lightweight concrete (SLWC) beam specimens without shear reinforcement. Comparisons of measured and predicted shear capacities of concrete beams in the database show that ACI 318-11 provisions for shear-transfer capacity of concrete are less conservative for lightweight concrete (LWC) beams than NWC beams. A rational approach based on the upper-bound theorem of concrete plasticity has been developed to assess the reduced aggregate interlock along the crack interfaces and predict the shear-transfer capacity of concrete. A simplified model for the modification factor is then proposed as a function of the compressive strength and dry density of concrete and maximum aggregate size on the basis of analytical parametric studies on the ratios of shear-transfer capacity of LWC to that of the companion NWC. The proposed modification factor decreases with the decrease in the dry density of concrete, gives closer predictions to experimental results than does the ACI 318-11 shear provision and, overall, improves the safety of shear capacity of LWC beams.

Master of Science / Department of Civil Engineering / Asadollah Esmaeily / The shear and combined shear and torsion provisions of the AASHTO LRFD (2008) Bridge Design Specifications, as well as simplified AASHTO procedure for prestressed and non-prestressed reinforced concrete members were investigated and compared to their equivalent ACI 318-08 provisions. Response-2000, an analytical tool developed based on the Modified Compression Field Theory (MCFT), was first validated against the existing experimental data and then used to generate the required data for cases where no experimental data was available. Several normal and prestressed beams, either simply supported or continuous were used to evaluate the AASHTO and ACI shear design provisions In addition, the AASHTO LRFD provisions for combined shear and torsion were investigated and their accuracy was validated against the available experimental data. These provisions were also compared to their equivalent ACI code requirements. The latest design procedures in both codes propose exact shear-torsion interaction equations that can directly be compared to the experimental results by considering all ϕ factors as one. In this comprehensive study, different over-reinforced, moderately-reinforced, and under-reinforced sections with high-strength and normal-strength concrete for both solid and hollow sections were analyzed. The main objectives of this study were to: • Evaluate the shear and the shear-torsion procedures proposed by AASHTO LRFD (2008) and ACI 318-08 • Validate the code procedures against the experimental results by mapping the experimental points on the code-based exact interaction diagrams • Develop a MathCAD program as a design tool for sections subjected to shear or combined shear and torsion

Experiments were conducted to investigate the punching shear behaviour of thick slabs with identical spans and depths, subjected to monotonic point load conditions. Variables included: reinforcement ratio, column size, and reinforcement size. Analytical studies conducted as part of this thesis indicate that the current CSA A23.3 and the ACI 318 can be unconservative for thick slabs with low reinforcement ratios. The new fib Model Code provisions for punching offer an effective method for determining the full load-rotation behaviour of a slab up to failure, including accurate failure predictions. A summary of the background of current design procedures and standards will be presented, and a comparison between the different design equations and theories will be given. Based on the findings of this project, it is proposed that the provisions accepted by the fib Model Code should be considered for implementation in the CSA and ACI standards.

Experiments were conducted to investigate the punching shear behaviour of thick slabs with identical spans and depths, subjected to monotonic point load conditions. Variables included: reinforcement ratio, column size, and reinforcement size. Analytical studies conducted as part of this thesis indicate that the current CSA A23.3 and the ACI 318 can be unconservative for thick slabs with low reinforcement ratios. The new fib Model Code provisions for punching offer an effective method for determining the full load-rotation behaviour of a slab up to failure, including accurate failure predictions. A summary of the background of current design procedures and standards will be presented, and a comparison between the different design equations and theories will be given. Based on the findings of this project, it is proposed that the provisions accepted by the fib Model Code should be considered for implementation in the CSA and ACI standards.

Shear strength of precast/prestressed hollow-core (PHC) slabs subjected to concentrated or line loads, especially near supports, may be critical and usually is the governing criteria in the design. This study presents the second phase of a research program, undergoing at the University of Manitoba, to calibrate the shear equations in the Canadian code for predicting the shear capacity of PHC slabs. This phase includes both experimental and numerical investigations using a finite element analysis (FEA) software package. The length of bearing, void shape and size, level of prestressing and shear span-to-depth ratio were investigated. The experimental results were compared to the predictions of the Canadian, American and European codes. It was concluded that the Canadian code is unduly conservative. However, the special European code for PHC slabs resulted in better and more consistent predictions. The FEA suggested that the adequate prestressing reinforcement ratio to obtain highest shear capacity ranges between 0.7% and 1.1%.

Shear strength of precast/prestressed hollow-core (PHC) slabs subjected to concentrated or line loads, especially near supports, may be critical and usually is the governing criteria in the design. This study presents the second phase of a research program, undergoing at the University of Manitoba, to calibrate the shear equations in the Canadian code for predicting the shear capacity of PHC slabs. This phase includes both experimental and numerical investigations using a finite element analysis (FEA) software package. The length of bearing, void shape and size, level of prestressing and shear span-to-depth ratio were investigated. The experimental results were compared to the predictions of the Canadian, American and European codes. It was concluded that the Canadian code is unduly conservative. However, the special European code for PHC slabs resulted in better and more consistent predictions. The FEA suggested that the adequate prestressing reinforcement ratio to obtain highest shear capacity ranges between 0.7% and 1.1%.

This diploma thesis deals with the comparison of design method of concrete constructions according to currently valid European standard EN 1992 and American standards ACI 318. For comparison was selected parts of the office building. In this work was assessed locally supported slab, columns and staircase.

This work deals with the analysis of reinforced concrete structures according to the currently valid standard EN 1992-1-1 (EC 2) compared with the analysis according to the American standard ACI 318-08. Static solution includes an assessment of slab in local supports, calculation of columns and footings according to 1st critical state for both standards. The slab is also assessed according to the 2st critical state according to EC 2.