The development of technologies to reduce turbofan engine noise reveals the fan noise, the first stage of an engine, as a great contributor for the total noise of an airplane. So a better understanding of the fan noise generation came up and motivated the construction of a fan rig test facility at the University of São Paulo in São Carlos by a partnership between the university and EMBRAER S.A.. The fan rig is composed of a long duct (12mlong) comprising a 16-bladed fan rotor and 14-vaned stator. The rotor is powered by an 100 hp electrical motor allowing speed up to 4250 RPM resulting in 0.1Mach axial flow. A 77-microphone wall-mounted array was designed for fan noise analysis. A cooperation with NASA-Glenn allowed data and information exchanging from their similar fan rig setup, the ANCF, grating then the validation of the in-house developed software. A short guide for duct-array is proposed in this work. Complex software was developed to process the data from the microphones array. We performed 3 different types of analysis: power spectral density, noise imaging obtained by acoustic beamforming and modal analysis.We proposed a different technique for modal analysis based on beamforming images in this work.We did not find any similar technique in the references. The results obtained by this technique were validated with data from ANCF-NASA. Comparative results are presented for both fan rigs, such as: power spectral densities for different fan speeds, modal analysis at the blade passing frequency (strong tones generated by the fan), noise imaging obtained by beamforming for rotating and static noise sources. Finally, results achieved in this work are in agreement with those observed in the references consulted. / Como desenvolver de tecnologias para redução de ruído de motores aeronáuticos turbofans, o ruído gerado pelo fan (primeiro estágio do motor) vem se mostrando cada vez mais um grande contribuinte na emissão total de ruído em um avião. Com isso, a necessidade de se estudar mecanismos geradores de ruído nestes motores veio à tona e motivou a construção de uma bancada de experimentos aero-acústicos junto àUniversidade de São Paulo, campus São Carlos, oriundo da parceria entre EMBRAER S.A. e Universidade de São Paulo. A bancada de ensaios compõe um conjunto rotor/estator, sendo que o fan (rotor) é equipado com 16 pás e a estatora 14 pás, conectado a um motor elétrico de 100 hp através de um eixo ao rotor, alcançando 4250 RPM com velocidade de escoamento axial médio de 0,1 Mach. Esta bancada é composta por um longo duto e a seção de ensaio com o fan localiza-se ao centro. Uma antena dispondo de 77 microfones foi especialmente projetada para fazer aquisição do ruído gerado pelo fan. Uma parceria com a NASA-Glenn possibilitou a troca de informações e dados experimentais de sua bancada de experimentos similar (ANCF) ajudando assim a validar os códigos desenvolvidos bem como comparar resultados para ambas as bancadas. Umpequeno roteiro para projeto de antena para análise modal e beamforming em duto é apresentado neste trabalho. Um complexo software foi desenvolvido a fim de processar sistematicamente os dados aquisitados pelos microfones da antena. Três tipos de análise são feitas: Via espectro densidade de potência; Imagem de ruído acústico obtido através da técnica de beamforming, e por último, análise modal. Uma técnica diferente para análise modal baseada em imagens obtidas através de beamforming é proposta neste trabalho. Nada similar foi encontrado nas referências consultadas. Os resultados foram validados com dados de fontes sintéticas produzidas pela bancada ANCF-NASA. Resultados comparativos para ambas as bancadas são exibidas neste trabalho, tais quais: Análise do espectro densidade de potência para diferentes rotações do fan; análise modal nas frequências de passagem das pás (forte ruído tonal gerado pelo fan); imagem acústica do ruído gerado tanto por fontes rotativas quanto para fontes estáticas. Finalmente, os resultados obtidos estão de acordo com o esperado e de antemão observados nas referências consultadas.

A redução do ruído externo gerado por aeronaves operando nas proximidades de grandes centros urbanos é apontada como uma questão vital para a manutenção e expansão sustentável das atividades da aviação civil. Nas últimas décadas, reduções significativas no ruído gerado pelos sistemas de propulsão da aeronave tornaram relevantes as contribuições do trem de pouso e dos dispositivos de hiper-sustentação (flapes e eslates) para o ruído global da aeronave. A caracterização do espectro acústico de cada componente hiper-sustentador é necessária para o desenvolvimento de métodos preditivos de ruído e projetos aerodinâmicos que viabilizem a redução de ruído sem penalizações severas para o desempenho e a segurança da aeronave. Experimentos com modelos em escalas mostram que a contribuição de cada elemento hiper-sustentador para o ruído global é determinada pelo tamanho e modelo da aeronave. Tal fato dificulta a generalização dos resultados experimentais e determina a caracterização do espectro acústico de cada componente de um aerofólio em termos de sua geometria e configuração operacional. Este trabalho tem como objetivo principal a caracterização do ruído do eslate a partir de medições experimentais com um aerofólio hiper-sustentador McDonnell Douglas (30P30N), composto por flape, eslate e elemento principal. Os experimentos foram realizados em túnel de vento de seção fechada, e as medições acústicas contaram com o uso de uma antena composta por 62 microfones. Os dados acústicos foram processados com algoritmos de beam-forming convencional e deconvolução DAMAS (Deconvolution Approach for the Mapping of Acoustic Sources). A aplicação de técnicas de beam-forming permite representar uma distribuição espacial de fontes na forma de um mapa acústico e determinar o nível de ruído gerado por fontes que concorrem de forma independente para o ruído global. A base de dados experimentais permite o estudo do ruído do eslate sob diferentes configurações operacionais e geométricas do aerofólio. A análise do espectro acústico do eslate revela a ocorrência de ruído tonal em baixa e alta frequências, e ruído de banda larga em média frequência. Os mapas de beam-forming obtidos associam o ruído de banda larga com uma distribuição bidimensional de fontes ao longo da envergadura do eslate. O ruído do eslate aumenta com a velocidade de escoamento livre, enquanto que os picos tonais de baixa frequência e o ruído de banda larga decrescem com o aumento do ângulo de ataque do aerofólio de 2° para 10°. Os espectros de ruído do eslate colapsam quando reescalados pelo número de Mach do escoamento livre elevado a uma potência entre 4 e 5, e o ruído tonal colapsa em Strouhal dado pela corda do eslate e pela velocidade do escoamento base. Os resultados mostram que o ruído do eslate é fortemente dependente da geometria do aerofólio, particularmente para variações de overlap. Uma boa correspondência quantitativa foi obtida comparando-se espectros experimentais de ruído do eslate com espectros numéricos, obtidos a partir de um modelo com a mesma geometria e em condições de teste idênticas, o que indica a viabilidade do uso de túneis de vento de secção fechada para a realização de experimentos aeroacústicos. / The reduction in the noise produced by aircraft operating in the vicinity of large urban centers is an important issue for a sustainable growth in the civil aviation activities. Over the last decades, from a signicant reduction achieved in the noise generated by aircraft propulsion systems, the contribution of both landing gears and high-lift devices (flaps and slats) has become important to the aircraft overall noise. The identication of the noise signature of each high-lift component is required for the development of both noise prediction methods and new aerodynamic design concepts toward achieving a noise reduction without severe penalty over the aircraft performance and safety. Scaled model experiments have shown that the importance of each airframe component to the overall noise is determined by particularities in both aircraft geometry and size. Such noise model dependence hampers the generalization of experimental results from a reference testing model and leads to the necessity of assessing noise generation according to the testing model geometry and operational condition. This study focuses mainly on the characterization of slat noise from experimental measurements on a high-lift Mcdonnell Douglas (30P30N) airfoil, composed of a slat, a ap and a main element. Measurements were performed in a closed-section wind tunnel by a 62-microphone array and the acoustic data were processed with in-house codes based on conventional beam-forming and DAMAS (Deconvolution Approach for theMapping of Acoustic Sources) algorithms. Beam-forming techniques potentially enable the representation of a spatial source distribution as an acoustic map, from which the contribution of independent sources to the overall noise can be estimated. The experimental database enables the study of the slat noise from dierent airfoil operational conditions and geometrical settings. The slat noise spectral signature reveals the occurrence of tonal noise over both low- and high-frequency bands and also broadband noise over a mid-frequency range. Beam-forming maps indicate the slat broad-band noise originates from a source spatially distributed along the slat span. The slat noise increases in function of the ow speed, whereas low-frequency tonal peaks and the broadband noise decrease as the airfoil angle of attack increases from 2 to 10. The slat noise spectra scalle when the Mach number is raised to a power between 4 and 5, and the tonal noise collapses with Strouhal based on the slat chord and the ow speed. Results show the slat noise is strongly in uenced by the airfoil geometry, particularly for variations in the overlap. A good quantitative agreement was achieved through the comparison between the experimental and numerical slat noise spectra for the same model geometry and test conditions, which indicates the viability of performing aeroacoustic experiments in closed-section wind tunnels.

Les gaines rectangulaires utilisées dans les réseaux de transport de gaz, notamment dans l'industrie de l'aluminium, sont soumises à des excitations provenant du flux s'écoulant à l'intérieur. Ce travail de thèse vise à comprendre quels sont les phénomènes impliqués dans la vibration des gaines rectangulaires de transport de gaz. Dans un premier temps nous présentons un modèle semi-analytique de gaine rectangulaire homogène basé sur le couplage de 4 plaques. Cette modélisation nous permet ainsi de définir les caractéristiques modales de la gaine. Ce modèle a été validé expérimentalement et numériquement par un code élément-finis. Dans un second temps, nous appliquons diverses excitations aérodynamiques et aéroacoustiques à notre gaine afin de déterminer quelles sont les contributions prépondérantes. Les comparaisons entre les résultats numériques et expérimentaux dans le cas d'un écoulement en gaine droite montrent que les contributions aéroacoustiques sont prépondérantes. Les mêmes tendances ressortent lors d'essais dans des configurations en coude, sauf à proximité de celui-ci où les sources aérodynamiques sont également importantes. Pour finir, nous appliquons ces recherches à une gaine rectangulaire utilisées dans l'industrie de l'aluminium. Nous constatons que le modèle que nous avons développé permet d'obtenir des tendances sur la réponse vibratoire de la gaine et met de nouveau en avant l'importance des contributions de type aéroacoustiques. Des pistes de réduction des niveaux vibratoires sont explorées et notamment celles de l'impact des paramètres géométriques de la structure. / Rectangular duct used for gas transport ductwork, especially in the aluminium industry, are excited by the internal flow. This thesis seeks to understand what are the phenomena involved in the vibration of the gaz transport ductwork. Firstly, we present a semi-analytical model of a homogeneous rectangular duct based on the coupling of 4 plates. This modeling allow us to define the duct modal characteristics and is validated by using both experimental and numerical (FEM) ways. Secondly, we applied aeroacoustic and aerodynamic excitations to our duct in order to determine which are the main contributions. Comparisons between numerical and experimental results, in the case of a straight duct highlight that aeroacoustic sources are predominant. The same trends are found with a bend configuration with few changes close to the band where aerodynamic sources seems to be predominant also. Finally, we apply our model to a large rectangular duct used in the aluminium industry. We note that the model gives good trends and highlights again the importance of the aeroacoustic contributions. Some reflexions about how to reduce the vibration levels by changing geometrical parameters are given at the end.

Αντικείμενο της εργασίας είναι η αεροδυναμική και αεροακουστική ανάλυση στροφείων ανεμοκινητήρων οριζοντίου άξονα (α-ο-α). Ο υπολογισμός του πεδίου ροής και των αεροδυναμικών συντελεστών του στροφείου ενός ανεμοκινητήρα επιτυγχάνεται κατά δύο τρόπους, με σκοπό την άμεση σύγκριση των αποτελεσμάτων με κριτήρια αφενός την ακρίβεια και αφετέρου την ευκολία ή πρακτικότητα που προσδιορίζεται κύρια σε όρους χρόνου υπολογισμού και διαθεσιμότητας υπολογιστικών πόρων. Οι δύο επιλεγμένοι τρόποι που διαφοροποιούνται στην φυσικο-μαθηματική μοντελοποίηση του προβλήματος ροής γύρω από το στροφείο του ανεμοκινητήρα, αποτελούν δύο δοκιμασμένες μεθοδολογίες ή τεχνικές ανάλυσης και σχεδιασμού περιστρεφόμενων στροφείων, τα οποία μπορούν να λειτουργούν ως κινητήριες μηχανές ή ως εργομηχανές, είναι η μέθοδος των επιφανειακών στοιχείων και η αριθμητική επίλυση των εξισώσεων Navier-Stokes. Για την αξιολόγηση των υπολογιστικών αποτελεσμάτων επιλέχθηκε ως στροφείο αναφοράς, ο πειραματικός ανεμοκινητήρας NREL phase II. Ο αλγόριθμος των επιφανειακών στοιχείων συμπλέχτηκε με ολοκληρωτικά σχήματα πρόλεξης και υπολογισμού του οριακού στρώματος με σκοπό να συμπεριληφθούν τα φαινόμενα συνεκτικότητας της ροής. Πραγματοποιήθηκε παραμετρική ανάλυση του δρομέα του ανεμοκινητήρα για διαφορετικές συνθήκες λειτουργίας του. Η σύγκριση των αποτελεσμάτων των συντελεστών πίεσης των περιστρεφόμενων πτερυγίων για τέσσερις θέσεις κατά το εκπέτασμα του πτερυγίου με τα πειραματικά δεδομένα δείχνει ικανοποιητική συμφωνία. Για την ανάλυση του πεδίου ροής που παράγεται γύρω από περιστρεφόμενους δρομείς α-ο-α χρησιμοποιήθηκε η μέθοδος της υπολογιστικής ρευστοδυναμικής (CFD). Πραγματοποιήθηκαν RANS προσομοιώσεις για διαφορετικές συνθήκες λειτουργίας του ανεμοκινητήρα και για τέσσερα διαφορετικά μοντέλα τύρβης. Το k-ω SST μοντέλο τύρβης έχει τις μικρότερες αποκλίσεις με τα πειραματικά αποτελέσματα. Η αεροακουστική ανάλυση του στροφείου ενός ανεμοκινητήρα επιτυγχάνεται με την επίλυση της ακουστικής εξίσωσης Ffowcs-Williams Hawkings, μέσω ενός υπολογιστικού κώδικα που αναπτύχθηκε γι’ αυτό το σκοπό. Από τα αποτελέσματα των προσομοιώσεων, φάνηκε στα ροδογράμματα κατευθυντικότητας του ήχου, τα επίπεδα της ακουστικής πίεσης να είναι υψηλότερα για θέσεις παρατηρητή ανάντη και κατάντη του ανεμοκινητήρα. / The aim of this study is to represent the aerodynamic and aeroacoustic analysis of horizontal axis wind turbine (ΗAWT) rotors. The calculation of the flow field and the aerodynamic coefficients over the wind turbine rotor are performed using two methodologies, the panel method and the numerical solution of Navier-Stokes equations. These two methodologies are differentiated in the mathematical modeling approach of the flow around the rotor and are utilized in the design and manufacturing phases of horizontal axis wind turbine rotors. Moreover, the results of these two methodologies are compared in terms of the accuracy and the computational time required. For the evaluation of the computational results the experimental wind turbine NREL phase II is chosen as the reference rotor. An invicid/viscous interaction algorithm is developed using integral boundary layer equations coupled with the low order panel method solution in order to account the viscous effects. A parametric analysis of the wind turbine rotor is conducted for different operating conditions. The comparison of the results of the pressure coefficients of the rotating blades for four spanwise positions along the blade with the experimental data shows satisfactory agreement. The analysis of the near and far flow field of HAWT is obtained via CFD by RANS simulations of four different turbulence models (Spalart-Allmaras, k-ε, k-ε RNG and k-ω SST). From the conducted study, it is confirmed the ability of analysis of a HAWT rotor flow field with the RANS equations and the good agreement of the computations with experimental data, when the k-ω SST turbulence model is used. The aeroacoustic analysis of the HAWT is based on the solution of the Ffowcs Williams-Hawkings (FW-H) equation via a computer code developed for this purpose. The radiation patterns of the calculated aeroacoustic noise show that high level amplitudes are calculated for upwind and downwind positions.

Lors des mesures acoustiques dans les souffleries à veine ouverte, les ondes acoustiques émises par une maquette ou une source située dans la veine se propagent dans la couche de cisaillement turbulente qui se forme aux abords du jet avant d’être reçues par les microphones localisés en dehors. L’onde acoustique interagit avec le champ de vitesse turbulent de la couche de mélange ce qui a pour effet de modifier son contenu spectral, de redistribuer spatialement son énergie et de moduler sa phase et son amplitude, on parle alors de diffusion acoustique. Cette thèse a consisté à l’étude de la diffusion d’une onde acoustique par une couche de cisaillement turbulente à l’aide d’une simulation numérique aux grandes échelles. Pour cela, il a d’abord été nécessaire de réaliser la simulation numérique aux grandes échelles d’une couche de cisaillement turbulente plane dans son régime auto-similaire. Dans un second temps, nous avons simulé l’interaction entre une onde acoustique et l’écoulement turbulent afin d’étudier les caractéristiques du champ de pression diffusé qui en résulte. Nous avons notamment vérifié que la simulation était capable de prédire précisément les fréquences sur lesquelles est répartie la plupart de l’énergie acoustique ainsi que la forme du spectre de pression diffusé. Finalement, le champ de vitesse du milieu turbulent qui est corrélé avec l’enveloppe du champ de pression diffusé a été reconstruit à l’aide de la méthode de l’estimation stochastique linéaire. Cette méthode nous a notamment permis de visualiser les larges structures turbulentes qui interviennent principalement dans le mécanisme de diffusion acoustique. / During open jet wind tunnel measurements, the acoustic waves emitted by a device or an acoustic source located inside the flow propagate inside the turbulent shear layer that develops at the periphery of the jet before being received by microphones located outside the flow. The acoustic wave interacts with the turbulent velocity field leading to a change of directivity, a phase and amplitude modulation as well as a spectral re-distribution of the acoustic energy over a band of frequencies. This phenomenon is known as acoustic scattering. This work has consisted in the study of the scattering of an acoustic wave by a turbulent shear layer using large-eddy simulation. The first step of the study has consisted in the large-eddy simulation of a turbulent shear layer in its self-similar state. In a second second step, the direct computation of the interaction between the acoustic wave and the turbulent flow has been performed in order to study the characteristics of the resulting scattered pressure field. It has been shown that the numerical simulation is able to accurately predict the frequencies on which the main part of the scattered energy is redistributed, as well as the shape of the scattered pressure spectrum. Finally, the turbulent velocity field which is correlated with the envelope of the scattered pressure field is reconstructed using the linear stochastic estimation method. This method has enabled the visualization of the large turbulent structures that mainly take part in the acoustic scattering mechanism.

Pendant sa mission, un lanceur est soumis à des excitations large bande, sévères, aérodynamiques, de provenances diverses, qui peuvent mettre en danger la survivabilité de la charge utile et de l’équipement électronique du véhicule, et par conséquent le succès de la mission. Les structures aérospatiales sont généralement caractérisées par l’utilisation de matériaux composites exotiques des configurations et des épaisseurs variantes, ainsi que par leurs géométries largement complexes. Il est donc d’une importance cruciale pour l’industrie aérospatiale moderne, le développement d’outils analytiques et numériques qui peuvent prédire avec précision la réponse vibroacoustique des structures larges, composites de différentes géométries et soumis à une combinaison des excitations aéroacoustiques. Récemment, un grand nombre de recherches ont été menées sur la modélisation des caractéristiques de propagation des ondes au sein des structures composites. Dans cette étude, la méthode des éléments finis ondulatoires (WFEM) est utilisée afin de prédire les caractéristiques de dispersion des ondes dans des structures composites orthotropes de géométries variables, nommément des plaques plates, des panneaux simplement courbés, des panneaux doublement courbés et des coques cylindriques. Ces caractéristiques sont initialement utilisées pour prédire la densité modale et le facteur de perte par couplage des structures connectées au milieu acoustique. Par la suite, la perte de transmission (TL) à large bande des structures modélisées dans le cadre d’une analyse statistique énergétique (SEA) dans un contexte ondulatoire est calculée. Principalement en raison de la complexité géométrique importante de structures, l’utilisation des éléments finis (FE) au sein de l’industrie aérospatiale est souvent inévitable. L’utilisation de ces modèles est limitée principalement à cause du temps de calcul exigé, même pour les calculs dans la bande basses fréquences. Au cours des dernières années, beaucoup de chercheurs travaillent sur la réduction de modèles FE, afin de rendre leur application possible pour des systèmes larges. Dans cette étude, l’approche de SOAR est adoptée, afin de minimiser le temps de calcul pour un système couplé de type structurel-acoustique, tout en conservant une précision satisfaisante de la prédiction dans un sens large bande. Le système est modélisé sous diverses excitations aéroacoustiques, nommément un champ acoustique diffus et une couche limite turbulente (TBL).La validation expérimentale des outils développés est réalisée sur un ensemble de structures sandwich composites orthotropes. Ces derniers sont utilisés afin de formuler une approche couche équivalente unique (ESL) pour la modélisation de la réponse spatiale du panneau dans le contexte d’une approche de matrice de raideur dynamique. L’effet de la température de la structure ainsi que du milieu acoustique sur la réponse du système vibroacoustique est examiné et analysé. Par la suite, un modèle de la structure SYLDA, également fait d’un matériau sandwich orthotrope, est testé principalement dans le but d’enquêter sur la nature de couplage entre ses divers sous-systèmes. La modélisation ESL précédemment développée est utilisé pour un calcul efficace de la réponse de la structure dans la gamme des basses et moyennes fréquences, tandis que pour des fréquences plus élevées, une hybridisation WFEM / FEM pour la modélisation des structures discontinues est utilisé. / During its mission, a launch vehicle is subject to broadband, severe, aeroacoustic and structure-borne excitations of various provenances, which can endanger the survivability of the payload and the vehicles electronic equipment, and consequently the success of the mission. Aerospace structures are generally characterized by the use of exotic composite materials of various configurations and thicknesses, as well as by their extensively complex geometries and connections between different subsystems. It is therefore of crucial importance for the modern aerospace industry, the development of analytical and numerical tools that can accurately predict the vibroacoustic response of large, composite structures of various geometries and subject to a combination of aeroacoustic excitations. Recently, a lot of research has been conducted on the modelling of wave propagation characteristics within composite structures. In this study, the Wave Finite Element Method (WFEM) is used in order to predict the wave dispersion characteristics within orthotropic composite structures of various geometries, namely flat panels, singly curved panels, doubly curved panels and cylindrical shells. These characteristics are initially used for predicting the modal density and the coupling loss factor of the structures connected to the acoustic medium. Subsequently the broad-band Transmission Loss (TL) of the modelled structures within a Statistical Energy Analysis (SEA) wave-context approach is calculated. Mainly due to the extensive geometric complexity of structures, the use of Finite Element(FE) modelling within the aerospace industry is frequently inevitable. The use of such models is limited mainly because of the large computation time demanded even for calculations in the low frequency range. During the last years, a lot of researchers focus on the model reduction of large FE models, in order to make their application feasible. In this study, the Second Order ARnoldi (SOAR) reduction approach is adopted, in order to minimize the computation time for a fully coupled composite structural-acoustic system, while at the same time retaining a satisfactory accuracy of the prediction in a broadband sense. The system is modelled under various aeroacoustic excitations, namely a diffused acoustic field and a Turbulent Boundary Layer (TBL) excitation. Experimental validation of the developed tools is conducted on a set of orthotropic sandwich composite structures. Initially, the wave propagation characteristics of a flat panel are measured and the experimental results are compared to the WFEM predictions. The later are used in order to formulate an Equivalent Single Layer (ESL) approach for the modelling of the spatial response of the panel within a dynamic stiffness matrix approach. The effect of the temperature of the structure as well as of the acoustic medium on the vibroacoustic response of the system is examined and analyzed. Subsequently, a model of the SYLDA structure, also made of an orthotropic sandwich material, is tested mainly in order to investigate the coupling nature between its various subsystems. The developed ESL modelling is used for an efficient calculation of the response of the structure in the lower frequency range, while for higher frequencies a hybrid WFEM/FEM formulation for modelling discontinuous structures is used.

In a society where environmental noise is becoming a major health and economical concern, sound emissions are an increasingly critical design factor for vehicle manufacturers. With about a quarter of the European population living close to roads with heavy traffic, traffic noise in urban landscapes has to be addressed first. The current introduction of electric vehicles on the market and the need for sound systems to alert their presence is causing a shift in mentalities requiring engineering methods that will have to treat noise management problems from a broader perspective. That in which noise emissions need not only be considered as a by-product of the design but as an integrated part of it. Developing more sustainable ground transportation will require a better understanding of the sound field emitted in various realistic operating conditions, beyond the current requirements set by the standard pass-by test, which is performed in a free-field. A key aspect to improve this understanding is the development of efficient numerical tools to predict the generation and propagation of sound from moving vehicles. In the present thesis, a methodology is proposed aimed at evaluating the pass-by sound field generated by vehicle acoustic sources in a simplified urban environment, with a focus on flow sound sources. Although it can be argued that the aerodynamic noise is still a minor component of the total emitted noise in urban driving conditions, this share will certainly increase in the near future with the introduction of quiet electric engines and more noise-efficient tyres on the market. This work presents a complete modelling of the problem from sound generation to sound propagation and pass-by analysis in three steps. Firstly, computation of the flow around the geometry of interest; secondly, extraction of the sound sources generated by the flow, and thirdly, propagation of the sound generated by the moving sources to observers including reflections and scattering by nearby surfaces. In the first step, the flow is solved using compressible detached-eddy simulations. The identification of the sound sources in the second step is performed using direct numerical beamforming with linear programming deconvolution, with the phased array pressure data being extracted from the flow simulations. The outcome of this step is a set of uncorrelated monopole sources. Step three uses this set as input to a propagation method based on a point-to-point moving source Green's function and a modified Kirchhoff integral under the Kirchhoff approximation to compute reflections on built surfaces. The methodology is demonstrated on the example of the aeroacoustic noise generated by a NACA air inlet moving in a simplified urban setting. Using this methodology gives insights on the sound generating mechanisms, on the source characteristics and on the sound field generated by the sources when moving in a simplified urban environment. / I ett samhälle där buller håller på att bli ett stort hälsoproblem och en ekonomisk belastning, är ljudutsläpp en allt viktigare aspekt för fordonstillverkare. Då ungefär en fjärdedel av den europeiska befolkningen bor nära vägar med tung trafik, är åtgärder för minskat trafikbuller i stadsmiljö en hög prioritet. Introduktionen av elfordon på marknaden och behovet av ljudsystem för att varna omgivningen kräver också ett nytt synsätt och tekniska angreppssätt som behandlar bullerproblemen ur ett bredare perspektiv. Buller bör inte längre betraktas som en biprodukt av konstruktionen, utan som en integrerad del av den. Att utveckla mer hållbara marktransporter kommer att kräva en bättre förståelse av det utstrålade ljudfältet vid olika realistiska driftsförhållanden, utöver de nuvarande standardiserade kraven för förbifartstest som utförs i ett fritt fält. En viktig aspekt för att förbättra denna förståelse är utvecklingen av effektiva numeriska verktyg för att beräkna ljudalstring och ljudutbredning från fordon i rörelse. I denna avhandling föreslås en metodik som syftar till att utvärdera förbifartsljud som alstras av fordons akustiska källor i en förenklad stadsmiljö, här med fokus på strömningsgenererat ljud. Även om det aerodynamiska bullret är fortfarande en liten del av de totala bullret från vägfordon i urbana miljöer, kommer denna andel säkerligen att öka inom en snar framtid med införandet av tysta elektriska motorer och de bullerreducerande däck som introduceras på marknaden. I detta arbete presenteras en komplett modellering av problemet från ljudalstring till ljudutbredning och förbifartsanalys i tre steg. Utgångspunkten är beräkningar av strömningen kring geometrin av intresse; det andra steget är identifiering av ljudkällorna som genereras av strömningen, och det tredje steget rör ljudutbredning från rörliga källor till observatörer, inklusive effekten av reflektioner och spridning från närliggande ytor. I det första steget löses flödet genom detached-eddy simulation (DES) för kompressibel strömning. Identifiering av ljudkällor i det andra steget görs med direkt numerisk lobformning med avfaltning med hjälp av linjärprogrammering, där källdata extraheras från flödessimuleringarna. Resultatet av detta steg är en uppsättning av okorrelerade akustiska monopolkällor. Steg tre utnyttjar dessa källor som indata till en ljudutbredningsmodel baserad på beräkningar punkt-till-punkt med Greensfunktioner för rörliga källor, och med en modifierad Kirchhoff-integral under Kirchhoffapproximationen för att beräkna reflektioner mot byggda ytor. Metodiken demonstreras med exemplet med det aeroakustiska ljud som genereras av ett NACA-luftintag som rör sig i en förenklad urban miljö. Med hjälp av denna metod kan man få insikter om ljudalstringsmekanismer, om källegenskaper och om ljudfältet som genereras av källor när de rör sig i en förenklad stadsmiljö. / <p>QC 20170425</p>

Ce travail tente d'analyser la réponse d'une jet axisymétrique turbulent à une excitation fluidique stationnaire et instationnaire lorsque le contenu fréquentiel et aziumutal (!,m) de la perturbation est maîtrisé. Le dispositif de contrôle utilisé est composé de 16 microjets ronds répartis sur le bord de fuite de la tuyère. L'utilisation des microjets provoque une réduction du champ acoustique rayonné (particulièrement pour le cas de contrôle stationnaire). Le champ aérodynamique est ensuite sondé grâce à des mesures fil chaud et PIV stéréoscopique résolue en temps. L'excitation instationnaire permet d'utiliser les moyennes de phase afin d'effectuer une décomposition triple du champ de vitesse. L'étude de la composante cyclique de la “réponse du jet” montre une synchronisation spatio-temporelle importante sur une grande étendue spatiale. En d'autres mots, le forçage a une grande autorité déterministe sur l'écoulement. De plus, la comparaison de la composante cyclique de la réponse du jet avec la théorie de la stabilité linéaire indique qu'il existe des ondes d'instabilité hydrodynamique au sein du jet. L'analyse du jet contrôlé par injection fluidique stationnaire montre ensuite comment l'effet du contrôle peut être expliqué par la déformation du champ moyen conduisant à la réduction du taux de croissance des ondes d'instabilité dans le jet. Cette déformation est dûe à l'introduction d'un couple de paramètre (nombre d'onde/fréquences) pour lequel le champ moyen de l'écoulement est stable. La réponse du jet étant turbulente, cela implique que les tensions de Reynolds déforment le champ moyen de manière à ce que les modes les plus instables aient des taux de croissance plus faibles. / This work investigates the response of an axisymetric turbulent jet to steady and unsteady fluidic florcing where the azimuthal wavenumber-frequency (!,m) content of the perturbation is well known. The control setup is composed of 16 round microjets azimutally distributed around the nozzle lip. Such actuation can lead to a decrease in the acoustic energy radiated by the jet (especially for the steady case). The aerodynamic fied is investigated using hotwire measurements and time-resolved stereoscopic PIV. Using the unsteady forcing, phase-averaging is possible, and this allows the implementation of a triple decomposition of the measurements. Examination of the cyclic component of the flow response shows that a non-negligible phase-locked fluctuation is obtained over a large spatial extent, in other words, the actuation has good deterministic control authority over the flow. Furthermore, comparison of the cyclic component of the flow response with Linear Stability Theory supports the idea that the jet response comprises linear hydrodynamic instability waves. Subsequent analysis of jets controlled by steady fluidic actuation shows how the control effect can be explained by a mean-flow modification that leads to the reduction of instability-wave growth rates ; the mean flow modification is argued to be due to the introduction of azimuthal wavenumber-frequency pairs to which the mean flow is stable. The response is therefore turbulent, and involves Reynolds stresses which deform the mean-field such that the most unstable modes have lower growth rates.