Medições realizadas em edifícios altos, em escala real, têm mostrado que o carregamento devido à ação do vento pode causar importantes efeitos de torção. A atual tendência de construção de prédios com formas e sistemas estruturais mais complexos promove a acentuação das excentricidades entre o centro de massa, centro elástico e o ponto de aplicação instantânea de forças aerodinâmicas. Soma-se a isso o fato de os edifícios altos modernos estarem se tornando cada vez mais esbeltos e leves, o que baixa a velocidade (do vento) de disparo de fenômenos como galope e drapejamento torcional, fazendo com que esta velocidade se aproxime cada vez mais das velocidades do vento consideradas nos projetos. Frente a isso, os efeitos dinâmicos, tanto de flexão como de torção, induzidos pelo vento em edifícios altos representam uma importante consideração nos projetos de estruturas modernas. Os métodos analíticos para determinação da resposta de edifícios altos submetidos à ação do vento, hoje disponíveis, não levam a resultados satisfatórios em casos de geometrias não regulares, bem como não contemplam efeitos torsionais. Seu uso também não é recomendado no caso de estruturas muito flexíveis, cujo movimento afeta as forças aerodinâmicas que nelas atuam. Nessas situações, a melhor opção para os engenheiros é um estudo mais detalhado dos efeitos do vento sobre a estrutura, através de ensaios de modelos em escala reduzida em túneis de vento, que simulem as características do vento natural. O objetivo deste trabalho é o desenvolvimento de um mecanismo que permita a obtenção da resposta de edifícios altos frente à ação do vento, a partir de ensaios em túnel de vento com modelos em escala reduzida. Busca-se determinar a resposta em termos de suas componentes médias e flutuantes. Admite-se que a parcela dinâmica contempla os dois modos fundamentais de vibração livre em flexão, ortogonais entre si e aproximados de forma linear, e o primeiro modo de torção, aproximado de forma constante. As simplificações adotadas permitem que os modelos tenham baixa complexidade de projeto e construção, diminuindo, assim, o custo da modelagem e tornando o processo experimental mais ágil. Para validar os resultados obtidos com a utilização do mecanismo desenvolvido foram realizados ensaios em escala reduzida do CAARC Standard Tall Building, edifício alto tomado como padrão para calibração de técnicas de modelagem aeroelástica, no Túnel de Vento Professor Joaquim Blessmann, da Universidade Federal do Rio Grande do Sul. Os resultados obtidos foram comparados com os valores publicados por outros pesquisadores e com resultados determinados a partir de ensaios de medidas de pressões em alta freqüência. A coerência entre os valores comparados permitiu concluir que o equipamento simula satisfatoriamente o comportamento dinâmico de edifícios altos submetidos à ação do vento, mesmo perante fenômenos aeroelásticos, como a ressonância por desprendimento alternado de vórtices. A partir dos resultados verificou-se também a importância dos efeitos dinâmicos de torção induzidos pela ação do vento, e a necessidade de que sejam apropriadamente considerados nos projetos / Measurements performed in full-scale high rise buildings have shown that wind loading may cause important torsional effects. The current trend of building construction, with new shapes and complex structural systems promotes an increase in the distances (eccentricities) among the center of mass, elastic center and the instantaneous point of application of the resulting wind loads. Furthermore, modern tall buildings are becoming increasingly light and slender, diminishing the trigger wind speed of some phenomena such as galloping and torsional flutter, bringing these velocities closer to the design wind speeds. Therefore, wind induced bending and torsional dynamic effects in tall buildings play an important role in the design of modern structures. The current analytical methods for the response determination of tall buildings under wind loading do not lead to reliable results for the non regular building shapes, as well as do not consider torsional effects. Also, its use is not recommended for the case of very flexible structures, where the structure´s own motion may affect the aerodynamic forces acting on it. In these situations, the best option for engineers is a more detailed study of the wind effects, through boundary layer wind tunnels. The aim of this study is the development of a device that allows the determination of the response of tall buildings under wind loading, through wind tunnel tests with reduced scale models. The goal is the determination of the responses in terms of its mean and fluctuating components. It is assumed that the dynamic parcel contemplates the two fundamental bending modes of vibration, orthogonal and linear, as well as the torsional mode, which is assumed constant along the height. The adopted simplifications allow for a low complexity in the process of model design and construction as well as for a very low modeling cost, making more efficient the whole testing process. To validate the device, tests were performed with a reduced scale model of the CAARC Standard Tall Building, which is taken as a standard for the calibration of aeroelastic modeling techniques, in Prof. Joaquim Blessmann boundary layer wind tunnel of the Federal University of Rio Grande do Sul. The obtained results were compared with other researchers' values as well as with results obtained from pressure measurements, in a rigid model. The agreement among the compared values allows the conclusion that the device simulates satisfactorily well the dynamic behaviour of high rise buildings under wind loading, even for aeroelastic phenomena such as the resonance due to vortex shedding. It was also verified the importance of the wind induced torsional effects and the need for its proper consideration in the design process.

The purpose of this study was to develop a robust fluid-structure-interaction (FSI) technology that can accurately model non-linear flutter responses for sub- and transonic fluid flow. The Euler equation set governs the fluid domain, which was spatially discretised by a vertex-centred edge-based finite volume method. A dual-timestepping method was employed for the purpose of temporal discretisation. Three upwind schemes were compared in terms of accuracy, efficiency and robustness, viz. Roe, HLLC (Harten-Lax-Van Leer with contact) and AUSM+-up Advection Up-stream Splitting Method). For this purpose, a second order unstructured MUSCL (Monotonic Upstream-centred Scheme for Conservation Laws) scheme, with van Albada limiter, was employed. The non-linear solid domain was resolved by a quadratic modal reduced order model (ROM), which was compared to a semi-analytical and linear modal ROM. The ROM equations were solved by a fourth order Runge-Kutta method. The fluid and solid were strongly coupled in a partitioned fashion with the information being passed at solver sub-iteration level. The developed FSI technology was verified and validated by applying it to test cases found in literature. It was demonstrated that accurate results may be obtained, with the HLLC upwind scheme offering the best balance between accuracy and robustness. Further, the quadratic ROM offered significantly improved accuracy when compared to the linear method. / Dissertation (MEng)--University of Pretoria, 2011. / Mechanical and Aeronautical Engineering / unrestricted

The workin this thesis deals with the development of anaeroelastic simulation tool for horizontal axis wind turbineapplications. Horizontal axiswind turbines can experience significanttime varying aerodynamic loads, potentially causing adverseeffects on structures, mechanical components, and powerproduction. The need of computational and experimentalprocedures for investigating aeroelastic stability and dynamicresponse have increased as wind turbines become lighter andmore flexible. A finite element model for simulation of the dynamicresponse of horizontal axis wind turbines has been developed.The simulations are performed using the commercial finiteelement software SOLVIA, which is a program developed forgeneral analyses, linear as well as non-linear, static as wellas dynamic. The aerodynamic model, used to transform the windflow field to loads on the blades, is a Blade- Element/Momentummodel. The aerodynamic code is developed by FFA (TheAeronautical Research Institute of Sweden) and is astate-of-the-art code incorporating a number of extensions tothe Blade-Element/Momentum formulation. SOSIS-W, developed byTeknikgruppen AB was used to develop wind time series formodelling different wind conditions. The model is rather general, and different configurations ofthe structural model and various type of wind conditions couldeasily be simulated. The model is primarily intended for use asa research tool when influences of specific dynamic effects areinvestigated. Simulation results for the three-bladed wind turbine Danwin180 kW are presented as a verification example. <b>Keywords:</b>aeroelastic modelling, rotor aerodynamics,structural dynamics, wind turbine, AERFORCE, SOSIS-W,SOLVIA / NR 20140805

This thesis summarizes investigations performed within design, analysis and experimental evaluation of flexible aircraft structures. Not only the problems, but rather the opportunities related to aeroelasticity are discussed. In the first part of the thesis, different concepts for using active aeroelastic configurations to increase aircraft performance are considered. In particular, one study deals with the minimization of the induced drag of a highly flexible wing by using multiple control surfaces. Another study deals with a possible implementation of a high-bandwidth piezo electric actuator for control applications using aeroelastic amplification. The second part of the thesis deals with the development of an approach for modeling and analysis of flexible structures considering uncertainties in analysis models. Especially in cases of large structural variations, such as fuel level variations, a fixed-base modal formulation in robust flutter analysis may lead to incorrect results. Besides a discussion about this issue, possible means of treating this problem are presented. / QC 20101130

The aerospace industry endeavours to improve modern aircraft capabilities in efficiency, endurance, and comfort. One means of achieving these goals is through new enhancements in aerodynamics. Increased wing aspect ratio is an example of further improving efficiency. However, this comes with new challenges including possibly adverse aero-elastic and aero-servo-elastic (ASE) phenomena. New computational methods and tools are emerging and there is a need for experimental data for validation. University of Victoria’s Centre for Aerospace Research (UVic CfAR) set out to design a 20kg ASE demonstrator using a remotely piloted aircraft (RPA). This aircraft was designed with the intent of exploring coupling between aero-elastic modes including coupling between the short period aerodynamic mode and the first out-of-plane elastic mode of the wing. This thesis discuses the implementation of instrumentation designed and integrated into the ASE RPA demonstrator to monitor the deformation of the elastic wing in-flight. A strain based measurement technique was selected for integration into the ASE aircraft. This choice was made for several reasons including its reliability regardless of outdoor lighting, relatively lightweight processing requirements for real time applications, and suitable sampling bandwidth. To compute the wing deformation from strain, a method, sometimes referred to as strain pattern analysis (SPA), utilizing linear combinations of reference modal shapes fit against the measured strain, was used. Although this method is not new, to the author’s knowledge, it is the first practical application to a reduced scale RPA demonstrator. The deformation measurement system was validated against a series of distributed static load tests on the ground. Distributed load cases along the wing demonstrated good out-of-plane measurement performance. A case where only load is applied near the root of the wing resulted in the largest error in part as the mode shapes generated are less suited to approximate the resulting shape. In general errors in out-of-plane displacement at the end of the flexible wing portion can be expected to be less than 5%. The displacement at the tip of the wing can be as great as 11% for the left wing whereas the right wing is 4.7%. This suggest an asymmetry between the left and right wings requiring specifically tuned FE models for each to achieve best results. Twist angles presented in tests were relatively small for accurate comparison against the reference measurement, which was relatively noisy. Generally, the deformation measurement by SPA technique followed the same twist behaviours as the reference. A twist case, unlikely to be seen in flight, provided some insight into twist measurement robustness. The work presented is merely a small step forward with many opportunities for further research. There is room for improvement of the FE model used to generate the mode shapes in the strain pattern analysis. Initial efforts focused on the flexible spar portion of the wing. With more work improvements could be achieved for the estimation of the rigid wing. Additionally, there was some asymmetry between each wing semi-span, and with some focus on the left wing its results could be improved to at least match that of the right wing. A real-time implementation was not completed and would be particularly interesting for use as feedback for flight control. Study of load alleviation techniques may benefit. Another topic of study is the combination of this method with other measurements, such as accelerometers, to provide improved performance state estimation through sensor fusion. / Graduate

Recent design trends in steam turbines strive for high aerodynamic loading and high aspect ratio to meet the demand of higher efficiency. These design trends together with the low structural frequency in last stage steam turbines increase the susceptibility of the turbine blades to flutter. Flutter is the self-excited and self-sustained aeroelastic instability phenomenon, which can result in rapid growth of blade vibration amplitude and eventually blade failure in a short period of time unless adequately damped. To prevent the occurrences of flutter before the operation of new steam turbines, a compromise between aeroelastic stability and stage efficiency has to be made in the steam turbine design process. Due to the high uncertainty in present flutter prediction methods, engineers use large safety margins in predicting flutter which can rule out designs with higher efficiency. The ability to predict flutter more accurately will allow engineers to push the design envelope with greater confidence and possibly create more efficient steam turbines. The present work aims to investigate the influence of tip clearance flow on the prediction of steam turbine flutter characteristics. Tip clearance flow effect is one of the critical factors in flutter analysis for the majority of aerodynamic work is done near the blade tip. Analysis of the impact of tip clearance flow on steam turbine flutter characteristics is therefore needed to formulate a more accurate aeroelastic stability prediction method in the design phase.Besides the tip leakage vortex, the induced vortices in the tip clearance flow can also influence blade flutter characteristics. However, the spatial distribution of the induced vortices cannot be resolved by URANS method for the limitation of turbulence models. The Detached-Eddy Simulation (DES) calculation is thus applied on a realistic-scale last stage steam turbine model to analyze the structure of induced vortices in the tip region. The influence of the tip leakage vortex and the induced vortices on flutter prediction are analyzed separately. The KTH Steam Turbine Flutter Test Case is used in the flutter analysis as a typical realistic-scale last stage steam turbine model. The energy method based on 3D unsteady CFD calculation is applied in the flutter analysis. Two CFD solvers, an in-house code LUFT and a commercial software ANSYS CFX, are used in the flutter analysis as verification of each other. The influence of tip leakage vortex on the steam turbine flutter prediction is analyzed by comparing the aeroelastic stability of two models: one with the tip gap and the other without the tip gap. Comparison between the flutter characteristics predicted by URANS and DES approaches is analyzed to investigate the influence of the induced vortices on blade flutter characteristics. The multiple induced vortices and their relative rotation around the tip leakage vortex in the KTH Steam Turbine Flutter Test Case are resolved by DES but not by URANS simulations. Both tip leakage vortex and induced vortices have an influence on blade loading on the rear half of the suction side near the blade tip. The flutter analysis results suggest that the tip clearance flow has a significant influence on blade aerodynamic damping at the least stable interblade phase angle (IBPA), while its influence on the overall shape of the damping curve is minor. At the least stable IBPA, the tip leakage vortex shows a stabilization effect on rotor aeroelastic stabilities while the induced vortices show a destabilization effect on it. Meanwhile, a non-linear unsteady flow behavior is observed due to the streamwise motion of induced vortices during blade oscillation, which phenomenon is only resolved in DES results.

Développer, à partir de zéro, un drone imitant le vol battu de l'insecte est une tâche ambitieuse et ardue pour un designer en raison du manque de savoir-faire en la matière. Pour en accélérer le développement pendant les phases de design préliminaires, un outil modélisant les phénomènes aéroélastiques du vol de l'insecte est un véritable atout pour le designer et est le sujet de cette thèse. Le cœur de cet outil est un solveur éléments finis 'structure' couplé, en utilisant une approche par tranche, à un modèle aérodynamique quasi-statique du vol de l'insecte prenant en compte la flexibilité de l'aile, à la fois selon l'envergure et la corde, mais aussi ses grands déplacements. L'ensemble est conçu de manière à contenir le coût de calcul tout en étant assez modulaire pour s'adapter à un large panel d'applications. Afin de valider l'intégralité de cet outil, un processus en deux étapes a été entrepris avec d'abord une approche numérique et ensuite une validation expérimentale grâce à un banc de caractérisation dédié. Les résultats du modèle concordent de manière satisfaisante dans les deux cas, capturant l'amortissement dû aux forces aérodynamiques, et ouvrent ainsi la voie à son utilisation pour le design de drones à ailes battantes. Pour démontrer l'intérêt de cette approche lors des phases de design préliminaires, deux applications sur un nano-drone résonant sont réalisées: la définition d'une stratégie d'actionnement efficace et la recherche d'une géométrie d'aile potentiellement intéressante d'un point de vue aérodynamique, en couplant l'outil de modélisation à un algorithme génétique. Les résultats obtenus sont cohérents avec ceux trouvés dans la nature et sont en cours d'implémentation sur le drone. / Developing insect-like flapping-wing drones from scratch is an ambitious and arduous task for designers due to a lack of well-established know-how. To speed up the development of such vehicles through the preliminary design stage, a framework modeling the aeroelastic phenomena encountered in insect flight is an asset and is the subject of this thesis. Its kernel is a FEM based structural solver coupled in a blade-element approach to a quasi-steady aerodynamic model of insect flight accounting for the wing flexibility, both in the spanwise and in the chordwise direction, and for its large displacement. The complete framework is devised so as to maintain the computation load low while being modular enough for a wide range of applications. To validate the overall aeroelastic framework, a two-steps process has been undertaken with in one hand numerical studies and in the other hand experimental ones acquired on a dedicated test bench. The framework computation agrees satisfactorily, capturing the damping due to the aerodynamic force, and thus paves the way for preliminary design applications of a flapping-wing vehicle. To exhibit the capabilities of the framework as a preliminary design tool, two applications on a resonant nano air vehicle are performed: the definition of an efficient actuation strategy and the search of an aerodynamic potentially interesting wing geometry by plugging the framework to a genetic algorithm. The results are coherent with the ones found in nature and are under implementation on the nano air vehicle.

The work in this thesis deals with the development of an aeroelastic simulation tool for horizontal axis wind turbine applications. Horizontal axis wind turbines can experience significant time varying aerodynamic loads, potentially causing adverse effects on structures, mechanical components, and power production. The needs for computational and experimental procedures for investigating aeroelastic stability and dynamic response have increased as wind turbines become lighter and more flexible. A finite element model for simulation of the dynamic response of horizontal axis wind turbines has been developed. The developed model uses the commercial finite element system MSC.Marc, focused on nonlinear design and analysis, to predict the structural response. The aerodynamic model, used to transform the wind flow field to loads on the blades, is a Blade-Element/Momentum model. The aerodynamic code is developed by The Swedish Defence Research Agency (FOI, previously named FFA) and is a state-of-the-art code incorporating a number of extensions to the Blade-Element/Momentum formulation. The software SOSIS-W, developed by Teknikgruppen AB was used to generate wind time series for modelling different wind conditions. The method is general, and different configurations of the structural model and various type of wind conditions can be simulated. The model is primarily intended for use as a research tool when influences of specific dynamic effects are investigated. Verification results are presented and discussed for an extensively tested Danwin 180 kW stall-controlled wind turbine. Code predictions of mechanical loads, fatigue and spectral properties, obtained at different conditions, have been compared with measurements. A comparison is also made between measured and calculated loads for the Tjæreborg 2 MW wind turbine during emergency braking of the rotor. The simulated results correspond well to measured data. / QC 20100826

In this thesis, computational aerodynamics, structural and aeroelastic analyses of the composite tactical unmanned air vehicle which is designed and manufactured in the Department of Aerospace Engineering are performed. Verification of the structural integrity of the air vehicle is shown at the minimum maneuvering and the dive speeds at the static limit loads which are calculated by the computational aerodynamics analysis of the full aircraft model. In the current work, aerodynamic loads are re-calculated for more accurately determined dive speed angle of attack in an effort to match the overall vertical pressure load more closely to the half of the aircraft weight at the positive load factor. Finite element models of the fuselage, wing and the vertical-horizontal tail plane are prepared including the filament wound boom connecting the wing and the tail plane. Structural analyses of the composite wing, vertical and horizontal tail plane are performed under the limit aerodynamic loads calculated at the corner points of the V-N diagram using the structural finite element model of the wing-tail plane combination only. Global finite element analysis of the wing-tail plane combination showed that composite and isotropic materials of the wing-tail plane combination have positive margins of safety. Woven carbon and E-glass fabric that was procured to be used for the serial production version of the airplane are characterized for the tensile properties by the tests. Comprehensive aeroelastic stability analyses of the airplane are conducted by adding one sub-structure at a time to the aeroelastic model. Specifically, aeroelastic models which are used are the wing only, wing-tail plane combination, complete air vehicle with and without wing control surfaces. With such a study it is intended to address the effect each sub-structure adds to the aeroelastic model on the critical aeroelastic stability modes and speeds, and to see how sensitive the aeroelastic stability modes and speeds are to model fidelity. Detailed structural and aeroelastic analyses showed that the airplane has sufficient structural integrity under the action of static limit loads, and no aeroelastic instability is expected to occur within the flight envelope of the airplane.

This thesis describes the analysis, fabrication and testing of a rotor with extremely flexible blades, focusing on application to a micro-helicopter. The flexibility of the rotor blades is such that they can be rolled into a compact volume and stowed inside the rotor hub. Stiffening and stabilization of the rotor is enabled by centrifugal forces acting on a tip mass. Centrifugal effects such as bifilar and propeller moments are investigated and the torsional equation of motion for a blade with low torsional stiffness is derived. Criteria for the design of the tip mass are also derived and it is chosen that the center of gravity of each blade section must be located ahead of the aerodynamic center. This thesis presents the design of 18-inch diameter two-bladed rotors having untwisted circular arc airfoil profile with constant chord. A systematic experimental investigation of the effect of various blade parameters on the stability of the rotor is conducted in hover and forward flight. These parameters include blade flexibility in bending and torsion, blade planform and mass distribution. Accordingly, several sets of blades varying these parameters are constructed and tested. It is observed that rotational speed and collective pitch angles have a significant effect on rotor stability. In addition, forward flight velocity is found to increase the blade stability. Next, the performance of flexible rotors is measured. In particular, they are compared to the performance of a rotor with rigid blades having an identical planform and airfoil section. It is found that the flexible blades are highly twisted during operation, resulting in a decreased efficiency compared to the rigid rotor blades. This induced twist is attributed to an unfavorable combination of tip body design and the propeller moment acting on it. Consequently, the blade design is modified and three different approaches to passively tailor the spanwise twist distribution for improved efficiency are investigated. In a first approach, extension-torsion composite material coupling is analyzed and it is shown that the centrifugal force acting on the tip mass is not large enough to balance the nose-down twist due to the propeller moment. The second concept makes use of the propeller moment acting on the tip mass located at an index angle to produce an untwisted blade in hover. It is constructed and tested. The result is an untwisted 18-inch diameter rotor whose maximum Figure of Merit is equal to 0.51 at a blade loading of 0.14. Moreover, this rotor is found to be stable for any collective pitch angle greater than 11 degrees. Finally, in a third approach, addition of a trailing-edge flap at the tip of the flexible rotor blade is investigated. This design is found to have a lower maximum Figure of Merit than that of an identical flexible rotor without a flap. However, addition of this control surface resulted in a stable rotor for any value of collective pitch angle. Future plans for increasing the efficiency of the flexible rotor blades and for developing an analytical model are described. / text