This master’s thesis deals with the design of a heat recovery steam generator. The introductory part of the thesis is dedicated to waste heat boilers, their division and their utilization in combined cycles gas turbine. In the following chapter, an analysis of the existing combined heat and power plant operation is performed. In the next part of the thesis, the conceptual layout of the new source is designed. Subsequently, the thermal calculation of the boiler is carried out as well as the design of individual heat exchanging surfaces. The sixth chapter deals with the strength calculation of the boiler and the outer piping, chambers and drum are designed here. At the end of the thesis there are described off-design states of the new combined cycle gas turbine.

The diploma thesis deals with the energy audit of the kindergarten building Špálova in Ostrava, according to order No. 480/2012 Sb. as amended. It is divided into three parts. The first part deals with the project of photovoltaic power plants in the energy audit, the second part analyzes the calculation procedures in the design of energy-saving measures and the third part completes the energy audit according to the requirements of the above-mentioned decree.

The Master’s thesis discusses wireless thermostat for a control boiler. In order to complete the project we have to design and realise the whole project with software design. The system contains two units, a master control and a measurement of regulation units. The project initially talks about regulation of heating systems for family houses and larger buildings like schools and stores for example. Next, the project describes the control and regulation units and their potential extension for effective and economical operation. Both units are equipped with microcontrollers, which these control each of function. The communication between both units is provided by wireless interface in free radio band ISM. There is a user interface for the master control unit’s regulation process. The measurement and regulation unit has only the possibility to switch between manual and automatic control for regulation of heating system.

Master´s thesis is about hot water distribution with using of heating cables. This work is divided into three parts. First part is main function of heating cables, second part is about solution and suggestion of water supply, including hot water heater in two different objects. Important thing is difference a variant of the heating cable and without it. The last part is experimental, whose task is to verify the properties of the cable.

The introduction of theoretical part deals with issue of fuel. There are basic kinds of fuels, their properties and calorific values. In next part a summary of types of boilers depending on the kind of fuel is described. A process of burning in each type is discussed. Then the basic issue of heat transmission, heat losses and design of individual elements of central heating system is described. In the second part there are two studies compared to each other. In the first one an automatic pellet boiler is used as a source of energy and in the second one it’s a heat pump, type air-water. At the end both of the variants are reviewed and the better option is chosen. In the last part the better option is designed, into detailed design documentation. Important design values for using the heating system and hot water service are calculated.

This theses deals with large objects heating issue, more precisely, heating of industrial halls. The theses focuses primarily on the most effective way of heating, given the economical and hygienical functionality of the object. Heating options of the object and selection of the most appropriate one, according to the specified documents, are also mentioned in this work.

This diploma thesis deals with the problems associated with acquisition of experimental data from technological unit for biomass combustion with nominal capacity of 1 MW, with regard to determination of thermal efficiency. In the introduction part, parameters of currently available biomass-based fuels as well as of those with large potential in the future are summarized. Further, a review in the field of biomass combustion technology is given. Biomass boilers are compared according to their technical parameters, function and benefits and drawbacks. In theoretical part methods for determination of thermal efficiency by direct method, indirect method and modified indirect method are described. Main parameters influencing resultant values of efficiency are included into the analysis. In final part an evaluation of real operational data from prototype unit combusting wooden chips is made. Recommendations for further experimental data gathering and their processing with the aim to evaluate thermal efficiency are suggested.

The Thesis solves the issue of a design and construction of piping specifically focused on boiler apparatus and its equipment. This issue is important for creation of the piping classes in the (PDMS) programmes and for acceleration of output parameters which are mainly the temperature, materials, variable parameters, etc. This leads to other problems such as service life, security, economy, etc., are.

Diploma thesis deals with design and comparison of heating systems. In diploma thesis is designed system with gas condensing boiler, system with heat pump and system with gas condensing boiler for heating and solar collectors for heating of hot water. Content of this thesis is calculation of house heat loss, design of radiators, design of heat systems including a check of protective components, regulation with the help of thermostatic radiator valve, calculation of economical evaluation and creation of design documentation. Design is made for systems with unified temperature fall 55/45. For the variation with heat pump is computed a possibility of using the heat pump as an univalent or bivalent heat source. In the analysis of costs is considered a usage of natural gas for heating and warming of hot water with a condensing boiler, annual consumption of electric energy for operation of electrical appliances in household, consumption of electric energy for operation of heat pump for heating and warming of hot water and consumption of electric energy for warming of hot water in case of system with solar collectors. In the final evaluation a pay-off period is determined.

The threat of depletion of fossil fuels is the driving force to diversify energy sources in the Czech Republic respectively in the European Union but also worldwide. One of these potential sources are being biomass boilers. The construction of these boilers has expanded in recent years because of government support for the construction of clean energy sources. Whether it is a burning of clean biomass or just incorporation of biomass to fossil fuels, teh substitution of fossil fuels and biomass boilers are the ideal solution. Their major advantages include significant reductions in emissions, mainly sulfur compounds, organic closure of the cycle of CO2 and disposal costs of spent residue.