BACKGROUND:Sweet sorghum is a domesticated grass containing a sugar-rich juice that can be readily utilized for ethanol production. Most of the sugar is stored inside the cells of the stalk tissue and can be difficult to release, a necessary step before conventional fermentation. While this crop holds much promise as an arid land sugar source for biofuel production, a number of challenges must be overcome. One lies in the inherent labile nature of the sugars in the stalks leading to a short usable storage time. Also, collection of sugars from the sweet sorghum stalks is usually accomplished by mechanical squeezing, but generally does not collect all of the available sugars.RESULTS:In this paper, we present two methods that address these challenges for utilization of sweet sorghum for biofuel production. The first method demonstrates a means to store sweet sorghum stalks in the field under semi-arid conditions. The second provides an efficient water extraction method that can collect as much of the available sugar as feasible. Operating parameters investigated include temperature, stalk size, and solid-liquid ratio that impact both the rate of sugar release and the maximal amount recovered with a goal of low water use. The most desirable conditions include 30degreesC, 0.6 ratio of solid to liquid (w/w), which collects 90 % of the available sugar. Variations in extraction methods did not alter the efficiency of the eventual ethanol fermentation.CONCLUSIONS:The water extraction method has the potential to be used for sugar extraction from both fresh sweet sorghum stalks and dried ones. When combined with current sugar extraction methods, the overall ethanol production efficiency would increase compared to current field practices.

Increasing differences in United States energy consumption and production has influenced the passing of legislation for biomass fuel production. To determine feasibility of energy crops for alternative fuels, research is needed to investigate dry matter yield over an extended harvest season; physical characteristics need to be described for potential harvesting problems; chemical characteristics described to identify selective harvest potential, optimal harvest timing, losses during harvest and storage; various harvest techniques investigated to identify potential cost savings; and impact of various storage techniques on quantity and quality of deliverable biomass. This study investigated the use of two sorghum varieties as a potential bioenergy feedstock where 20 ha were planted for three years. Standing crop samples were collected from August through January to document changes in dry matter yield, moisture, height, fiber content, proximate and ultimate analysis. The sorghum was cut and conditioned – as a two-cutting ratoon or single-cutting – using various mower-conditioners and windrow samples taken daily to determine best method of field drying, quantify dry matter loss and soil entrainment. Two storage methods were utilized – baling with wrapping in a tubeline, and chopping and compressing in bag using a modified cotton module builder – to determine best method of storage for reduced dry matter loss. The optimal time of harvest for maximum dry matter occurred with the November once-cut where 30 Mg ha^-1 was documented, but comparable yields were observed with the two-cutting scenario. Fiber content increased with maturity, peaked, and declined, while ash content and moisture decreased with maturity. The achievement of 55% moisture in January shows field curing to be necessary for transportation at any significant distance, but soil entrainment – as measured by ash concentration – was not found to be a significant problem after conditioning, multiple windrow inversions, and harvesting. The geometric mean length of particle was determined to be 1.4 to 3.7 times lower than nominal chop length, indicating potential cost savings in comminution. Dry matter loss estimates during storage proved difficult due to mobility of moisture throughout the packages, where losses were documented up to 40%. Module packages tended to have lower dry matter and constituent losses than bales.

This thesis presents work on a holistic approach for improving the overall design of solar cooling systems driven by solar thermal collectors. Newly developed methods for thermodynamic optimization of hydraulics and control were used to redesign an existing pilot plant. Measurements taken from the newly developed system show an 81% increase of the Solar Cooling Efficiency (SCEth) factor compared to the original pilot system. In addition to the improvements in system design, new efficiency factors for benchmarking solar cooling systems are presented. The Solar Supply Efficiency (SSEth) factor provides a means of quantifying the quality of solar thermal charging systems relative to the usable heat to drive the sorption process. The product of the SSEth with the already established COPth of the chiller, leads to the SCEth factor which, for the first time, provides a clear and concise benchmarking method for the overall design of solar cooling systems. Furthermore, the definition of a coefficient of performance, including irreversibilities from energy conversion (COPcon), enables a direct comparison of compression and sorption chiller technology. This new performance metric is applicable to all low-temperature heat-supply machines for direct comparison of different types or technologies. The achieved findings of this work led to an optimized generic design for solar cooling systems, which was successfully transferred to the market.