Polymer electrolyte membrane fuel cells (PEMFCs) exhibit encouraging potential as an enabling technology for the Hydrogen Economy. Currently an important barrier to commercialization is the cost associated with existing PEMFC materials; this project???s goal was to investigate alternative materials for PEMFC bipolar plates. Conductive thermoplastic materials offer the promise of low density, low cost processing, and inexpensive resins, and were the focus of material development for PEMFC bipolar plate applications. In order to develop a thermoplastic bipolar plate this study utilized the combination of a low cost injection moldable commodity polymer resin, and low cost carbon materials as conductive fillers. The materials selected and tested included; a polypropylene copolymer; acetylene carbon black; Vulcan carbon black; and short carbon fiber. The components were combined in a twin screw extruder and injection molded into samples for testing. The result was a spectrum of composite samples with a range of filler loadings from 0 to 60 wt% and varying filler type ratios. Synergy between the different carbon types was achieved which led to better physical properties, specifically conductivity. The novel blends produced were tested for electrical conductivity, mechanical properties, rheology, microscopy, and actual plates were made and tested in a single cell PEMFC. These trials enabled discussion around the feasibility of the materials with respect to processability, cost, and performance (both in the fuel cell and in potential applications). The most significant results were measured using a composite blend with 54 wt% filler loading and a 1:1:1 filler ratio. Mechanical results achieved 68% and 100% of the industry targets for tensile and flexural strength, respectively. Tensile strength attained 27.7 MPa and flexural strength measured 82.8 MPa. Electrical conductivity results for the same samples varied between the two methods of measurement used. Using a fuel cell industry recommended procedure 2.2 S/cm was achieved and using a four point ASTM measurement technique 12.0 S/cm was reported. These values represent 3% to 12% of the industry target. Actual 16 cm2 fuel cell plates were produced, fuel cell hardware constructed and assembled, and the power output was found to be 51% relative to graphite plates. Thermoplastic bipolar plates for PEMFCs made of composite materials is promising, but optimum filler loading that balances all properties is still required in order to achieve conductivity targets. Nevertheless this study has demonstrated that conductive thermoplastic bipolar plates can be produced via injection molding.

The largest cost in manufacturing PEM fuel cells for automotive applications is due to the bipolar plate. The current graphite material used for the bipolar plate is very brittle and difficult to machine to the rigorous specifications needed for fuel cell stacks. This paper introduces the development of a fuel cell test stand for simultaneous testing of six individual fuel cells. To establish a long-term performance evaluation, the fuel cells incorporate a baseline graphite material that undergoes testing in the fuel cell environment. The graphite is an industry standard material that should not corrode when subjected to continual testing. The baseline model will be used in development of novel composite materials that will be tested under the same conditions for comparison to the graphite. Furthermore, the new materials and applied manufacturing methods could reduce the overall cost of fuel cell stacks in the future. Funding for this project was generously donated by the Virginia Center for Innovative Technology and the National Science Foundation. / Master of Science

Polymer electrolyte membrane fuel cells (PEMFCs) exhibit encouraging potential as an enabling technology for the Hydrogen Economy. Currently an important barrier to commercialization is the cost associated with existing PEMFC materials; this project’s goal was to investigate alternative materials for PEMFC bipolar plates. Conductive thermoplastic materials offer the promise of low density, low cost processing, and inexpensive resins, and were the focus of material development for PEMFC bipolar plate applications. In order to develop a thermoplastic bipolar plate this study utilized the combination of a low cost injection moldable commodity polymer resin, and low cost carbon materials as conductive fillers. The materials selected and tested included; a polypropylene copolymer; acetylene carbon black; Vulcan carbon black; and short carbon fiber. The components were combined in a twin screw extruder and injection molded into samples for testing. The result was a spectrum of composite samples with a range of filler loadings from 0 to 60 wt% and varying filler type ratios. Synergy between the different carbon types was achieved which led to better physical properties, specifically conductivity. The novel blends produced were tested for electrical conductivity, mechanical properties, rheology, microscopy, and actual plates were made and tested in a single cell PEMFC. These trials enabled discussion around the feasibility of the materials with respect to processability, cost, and performance (both in the fuel cell and in potential applications). The most significant results were measured using a composite blend with 54 wt% filler loading and a 1:1:1 filler ratio. Mechanical results achieved 68% and 100% of the industry targets for tensile and flexural strength, respectively. Tensile strength attained 27.7 MPa and flexural strength measured 82.8 MPa. Electrical conductivity results for the same samples varied between the two methods of measurement used. Using a fuel cell industry recommended procedure 2.2 S/cm was achieved and using a four point ASTM measurement technique 12.0 S/cm was reported. These values represent 3% to 12% of the industry target. Actual 16 cm2 fuel cell plates were produced, fuel cell hardware constructed and assembled, and the power output was found to be 51% relative to graphite plates. Thermoplastic bipolar plates for PEMFCs made of composite materials is promising, but optimum filler loading that balances all properties is still required in order to achieve conductivity targets. Nevertheless this study has demonstrated that conductive thermoplastic bipolar plates can be produced via injection molding.

The performance characteristics of pure hydrogen PEMFC (called HFC) stacks made with heterogeneous carbon fiber bipolar plates are studied in this thesis. In addition, the problem that the heterogeneous carbon fiber bipolar plate leaks in the high gas pressure is also solved in this studies so that the new plate can be used to the high current power sources. Because of the gas leakage of the first generation stack at high inlet gas pressure, the fuel supply is insufficient in the high current density. A 4-cell PEMFC stack made with this new bipolar plate is built with weight 370 g and volume 385 cm3 without a fan. The total power out of the 4-cell stack is about 30 W at room temperature. The specific power and volumetric power densities are 81 mW/g and 78 mW/cm3, respectively. The average power density is about 160 mW/cm2, but the power density of a single-cell can reach a value about 220 mW/cm2. The insufficient fuel supply cause that the power density of 4-cell PEMFC stack is lower than single cell, so it is necessary to solve the gas leakage at high pressure. Our experiment found that gas leakage occurs in heterogeneous bipolar plates can be relate to the insufficient or improper hot-pressing temperature, time and pressure while we are making the carbon fiber bunches. So the processes in making new carbon fiber bunches include water expansion, uniform glue adding, high hot-pressing pressure, and using proper temperature and enough solidification time. The airtight of the second generation of heterogeneous carbon fiber bipolar plates improves obviously with the new processes. No leakage occurs for gas pressure under 1atm. We expect that this design can be used to high inlet pressure. It is also quite suitable for various high-power electrical sources.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: This thesis gives a cost model for the manufacture of bipolar plates in South Africa. The methods for the manufacture considered are machining, using a micro-milling machine, and compression moulding. The focus of this thesis is on compression moulding. Details of the work done towards developing and validating the models are described, and then the cost models are discussed in detail. The results of the analysis done using the cost model is given with attention paid to the effect of changing design parameters, such as channel size and flow field area, and of the cost of production for both methods over various production volumes. The thesis concludes that compression moulding becomes the better option for production volumes greater than 324 bipolar plates, with a cost that eventually reaches close to R140 per plate for high enough production volumes (over 5000). The cost to produce 1000 plates using compression moulding is estimated at R294 per plate. An increase of the channel size gives a small reduction in the total cost, while the increase in cost with an increase in flow field area is large. / AFRIKAANSE OPSOMMING: Hierdie tesis gee 'n koste-model vir die vervaardiging van bipolêre plate in Suid- Afrika. Die vervaardigingsmetodes wat oorweeg word, is masjinering deur 'n mikro-freesmasjien en persvorming. Die fokus van hierdie tesis is op persvorming. Die besonderhede van die ontwikkeling en validering van die modelle word beskryf, en daarna word die modelle in besonderhede beskryf. Die resultate van 'n analise wat met die koste-model gedoen is, word daarna gegee, met die oorweging van die verandering van ontwerp-parameters soos die vloeikanaalgrootte en vloeiveld-area, en van die koste van vervaardiging vir beide metodes vir verskeie produksievolumes. Die tesis kom tot die slotsom dat persvorming die voorkeurproses is vir produksievolumes groter as 324 bipolêre plate, met 'n koste wat tot naastenby R140 per plaat daal vir hoë produksievolumes (meer as 5000). Die koste om 1000 plate met persvorming te maak, word op R294 per plaat beraam. 'n Toename in kanaalgrootte gee 'n klein vermindering in die totale koste, terwyl die toename in koste groot is wanneer die vloeiveld-area toeneem.

A nickel alloy with high chrome and molybdenum content was found to form a highly resistive and passive oxide layer. The donor density and mobility of ions in the oxide layer has been determined as a function of the electrical potential when alkaline water layers are on the alloy surface in order to account for the relative inertness of the nickel alloy in corrosive environments.

Neste trabalho foram analisados diferentes parâmetros geométricos para canais de fluxo em células a combustível tipo PEMFC e sua influência no desempenho do sistema, utilizando a fluidodinâmica computacional. Na análise dos modelos matemáticos, verificou-se que o modelo de aglomerado inundado descreve com maior fidelidade o comportamento de células a combustível, enquanto as equações de Butler-Volmer não consideram as perdas por transporte de massa. Foram avaliadas as seções transversais retangular, trapezoidal e em degrau. O modelo com canais de seção retangular apresentou desempenho elétrico ligeiramente superior, porém os canais com seção trapezoidal propiciam um melhor gerenciamento de água. Em todos os aspectos estudados, os canais com seção em degrau se comportaram de forma análoga aos canais com seção trapezoidal, porém sua construção é menos complexa. Também foram analisadas as configurações serpentina e interdigitada em células de 5 cm², e sua influência na uniformidade da densidade de corrente. Não foram observadas diferenças significativas quanto à eficiência elétrica entre células com as duas configurações. A configuração interdigitada propiciou distribuição mais uniforme de geração de corrente, pois os reagentes são fornecidos em alta concentração por uma maior área da célula. Assim, esta configuração é preferível para aumento de escala. / In this work, different geometric parameters for PEMFC flow channels and their influence in cell performance were analyzed using computational fluid dynamics. At first, two mathematical models, the flooded agglomerate model and the Butler-Volmer equations, were compared. It was verified that the equations do not consider mass-transfer losses, while the agglomerate model describes the system more accurately. In a second analysis, rectangular, trapezoidal and step-shaped cross-sections were evaluated. The model with rectangular channels showed a slightly higher electrical performance; however, trapezoidal channels provided better water management. Cells with step-shaped cross-sections were found to be superior to those with trapezoidal channels, due to lower constructive complexity, even though their performance was similar to that of trapezoidal cross-sections in every aspect. Further studies analyzed serpentine and interdigitated channel patterns in 5 cm² cells and their influence in current density uniformity. Again, electrical performance was very similar for both patterns. However, the interdigitated pattern provided more spatial uniformity in current generation, because concentrated reactants are supplied to a wider area of the cell. Thus, this pattern is preferable for fuel cell scaling-up.

This project is aimed at developing and demonstrating highly conductive, lightweight, and low-cost thermoplastic blends to be used as flow field bipolar plates for polymer electrolyte membrane (PEM) fuel cells. <br><br> The research is focused on designing, prototyping, and testing carbon-filled thermoplastic composites with high electrical conductivity, as well as suitable mechanical and process properties. <br><br> The impact of different types of fillers on the composite blend properties was evaluated, as well as the synergetic effect of mixtures of fill types within a thermoplastic polymer matrix. A number of blends were produced by varying the filler percentages. Composites with loadings up to 65% by weight of graphite, conductive carbon black, and carbon fibers were investigated. Research results show that three-filler composites exhibit better performance than single or two-filler composites. <br><br> Injection and compression molding of the conductive carbon filled polypropylene blend was used to fabricate the bipolar plates. A Thermal Gravimetric Analysis (TGA) was used to determine the actual filler loading of composites. A Scanning Electron Microscope (SEM) technique was use as an effective way to view the microstructure of composite for properties such as edge effects, porosity, and fiber alignment. Density and mechanical properties of conductive thermoplastic composites were also investigated. During this study, it was found that 1:1:1 SG-4012/VCB/CF composites showed better performance than other blends. The highest conductivity, 1900 S/m in in-plane and 156 S/m in through plane conductivity, is obtained with the 65% composite. Mechanical properties such as tensile modulus, tensile strength, flexural modulus and flexural strength for 65% 1:1:1 SG-4012/VCB/CF composite were found to be 584. 3 MPa, 9. 50 MPa, 6. 82 GPa and 47. 7 MPa, respectively, and these mechanical properties were found to meet minimum mechanical property requirements for bipolar plates. The highest density for bipolar plate developed in this project is 1. 33 g/cm³ and is far less than that of graphite bipolar plate. <br><br> A novel technique for metal insert bipolar plate construction was also developed for this project. With a copper sheet insert, the in-plane conductivity of bipolar plate was found to be significantly improved. The performance of composite and copper sheet insert bipolar plates was investigated in a single cell fuel cell. All the composites bipolar plates showed lower performance than the graphite bipolar plate on current-voltage (I-V) polarization curve testing. Although the copper sheet insert bipolar plates were very conductive in in-plane conductivity, there was little improvement in single cell performance compared with the composite bipolar plates. <br><br> This work also investigated the factors affecting bipolar plate resistance measurement, which is important for fuel cell bipolar plate design and material selection. Bipolar plate surface area (S) and surface area over thickness (S/T) ratio was showed to have significant effects on the significance of interfacial contact resistances. At high S/T ratio, the contact resistance was found to be most significant for thermoplastic blends. Other factors such as thickness, material properties, surface geometry and clamping pressure were also found to affect the bipolar plate resistance measurements significantly.

This project is aimed at developing and demonstrating highly conductive, lightweight, and low-cost thermoplastic blends to be used as flow field bipolar plates for polymer electrolyte membrane (PEM) fuel cells. <br><br> The research is focused on designing, prototyping, and testing carbon-filled thermoplastic composites with high electrical conductivity, as well as suitable mechanical and process properties. <br><br> The impact of different types of fillers on the composite blend properties was evaluated, as well as the synergetic effect of mixtures of fill types within a thermoplastic polymer matrix. A number of blends were produced by varying the filler percentages. Composites with loadings up to 65% by weight of graphite, conductive carbon black, and carbon fibers were investigated. Research results show that three-filler composites exhibit better performance than single or two-filler composites. <br><br> Injection and compression molding of the conductive carbon filled polypropylene blend was used to fabricate the bipolar plates. A Thermal Gravimetric Analysis (TGA) was used to determine the actual filler loading of composites. A Scanning Electron Microscope (SEM) technique was use as an effective way to view the microstructure of composite for properties such as edge effects, porosity, and fiber alignment. Density and mechanical properties of conductive thermoplastic composites were also investigated. During this study, it was found that 1:1:1 SG-4012/VCB/CF composites showed better performance than other blends. The highest conductivity, 1900 S/m in in-plane and 156 S/m in through plane conductivity, is obtained with the 65% composite. Mechanical properties such as tensile modulus, tensile strength, flexural modulus and flexural strength for 65% 1:1:1 SG-4012/VCB/CF composite were found to be 584. 3 MPa, 9. 50 MPa, 6. 82 GPa and 47. 7 MPa, respectively, and these mechanical properties were found to meet minimum mechanical property requirements for bipolar plates. The highest density for bipolar plate developed in this project is 1. 33 g/cm³ and is far less than that of graphite bipolar plate. <br><br> A novel technique for metal insert bipolar plate construction was also developed for this project. With a copper sheet insert, the in-plane conductivity of bipolar plate was found to be significantly improved. The performance of composite and copper sheet insert bipolar plates was investigated in a single cell fuel cell. All the composites bipolar plates showed lower performance than the graphite bipolar plate on current-voltage (I-V) polarization curve testing. Although the copper sheet insert bipolar plates were very conductive in in-plane conductivity, there was little improvement in single cell performance compared with the composite bipolar plates. <br><br> This work also investigated the factors affecting bipolar plate resistance measurement, which is important for fuel cell bipolar plate design and material selection. Bipolar plate surface area (S) and surface area over thickness (S/T) ratio was showed to have significant effects on the significance of interfacial contact resistances. At high S/T ratio, the contact resistance was found to be most significant for thermoplastic blends. Other factors such as thickness, material properties, surface geometry and clamping pressure were also found to affect the bipolar plate resistance measurements significantly.

Polymer electrolyte membrane fuel cells (PEMFCs) have the potential to play a major role as energy generators for transportation and portable applications. One of the current barriers to their commercialization is the cost of the components and manufacturing, specifically the bipolar plates. One approach to preparing PEMFCs for commercialization is to develop new bipolar plate materials, related to mass production of fuel cells. Thermoplastic/carbon filler composites with low filler loading have a major advantage in that they can be produced by a conventional low-cost injection molding technique. In addition, the materials used are inexpensive, easy to shape, and lightweight. An optimal bipolar plate must possess high surface and bulk electronic conductivity, sufficient mechanical integrity, low permeability, and corrosion resistance. However, it is difficult to achieve high electrical conductivity from a low-cost thermoplastic composite with low conductive filler loading. Concerns over electrical conductivity improvement and the injection processability of composites have brought forth the idea of producing a polypropylene/three-carbon-filler composite for bipolar plate application. The thesis addresses the development of synergistic effects of filler combinations, investigating composite conductive materials and using composite bipolar plate testing in PEMFCs. One significant effect of conductive network formation is the synergetic effects of different carbon filler sizes, shapes, and multiple filler ratios on the electrical conductivity of bipolar plate materials. A polypropylene resin combined with low-cost conductive fillers (graphite, conductive carbon black, and carbon fibers with 55 wt% of filler loading) compose the main composite for all investigations in this research. Numerous composite formulations, based on single-, two-, and three-filler systems, have been created to investigate the characteristics and synergistic effects of multiple fillers on composite conductivity. Electrical conductivity measurements corresponding to PEMFC performance and processing characteristics were investigated. Experimental work also involved other ex-situ testing for the physical requirements of commercial bipolar plates. All combinations of fillers were found to have a significant synergistic effect that increased the composite electrical conductivity. Carbon black was found to have the highest influence on the increase of electrical conductivity compared to the other fillers. The use of conjugated conducting polymers such as polypyrrole (PPy) to help the composite blends gain desirable conductivities was also studied. Electrical conductivity was significantly improved conductivity by enriching the conducting paths on the interfaces between fillers and the PP matrix with PPy. The conductive network was found to have a linkage of carbon fibers following the respective size distributions of fibers. The combination of Fortafil and Asbury carbon fiber mixture ameliorated the structure of conductive paths, especially in the through-plane direction. However, using small fibers such as carbon nanofibers did not significantly improve in electrical conductivity. The useful characteristics of an individual filler and filler supportive functions were combined to create a novel formula that significantly improved electrical conductivity. Other properties, such as mechanical and rheological ones, demonstrate the potential to use the composites in bipolar plate applications. This research contributes a direction for further improvement of marketable thermoplastic bipolar plate composite materials.