This thesis discusses the design considerations for a machine conditioning sensor utilizing Bluetooth low energy (BLE).

Approved for public release, distribution is unlimited / This thesis studies the feasibility of developing a closed-loop shipboard sensor calibration system with two main objectives. The first objective was to reduce the number of personnel required to calibrate a shipboard sensor by 50%. The second was to reduce the time required to complete the calibration process by 60%. This was achieved by displaying the sensor data and the calibration standard data on a tablet PC. Wireless technology was used to transmit the data from the sensor and the calibration standard to the tablet PC. The data from the sensor is sent via IEEE 802.11b wireless LAN using DataSocket protocol and the calibration standard is sent via Bluetooth protocol. The technology can be installed and used on current ships in the United States Navy. Four software programs were developed to accomplish these goals. One program runs on the tablet PC and the other three run on the network capable application processor (NCAP). These four programs accomplish the goals stated. / Lieutenant, United States Navy

Thesis (Ph. D.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2008. / Laskar, Joy, Committee Chair ; Cressler, John, Committee Member ; Kornegay, Kevin, Committee Member ; Tentzeris, Emmanouil, Committee Member ; Lee, Chang-Ho, Committee Member.

Thesis (M.Sc. (Computer Science)) - Rhodes University, 2007.

Práce se zabývá návrhem stabilního a rychlého bezdrátového spojení mezi dvěma body. K vytvoření tohoto spojení bude použita technologie Bluetooth a nebo její moderní alternativy vzhledem k tomu, že tato technologie již byla v daném pracovním prostředí testována a byla prokázána její stabilita. V této práci a v navazující diplomové práci budou diskutovány výsledky časových analýz zvolených senzorů, komunikace mezi senzorem a zvoleným mikrokontrolerem a nakonec návrh kompletního řešení, na jehož základě bude vytvořen funkční prototyp požadovaného zařízení.

In this thesis I present my analysis on various aspects of Bluetooth wireless technology. The Bluetooth technology is relatively new as compared to other technologies and there is huge potential of its growth and practical application. Therefore during in this thesis I try to analysis the current status of this technology and issue which are related to this technology. The first section introduces Bluetooth technology, in which I discussed the architecture of Bluetooth and different terminologies of Bluetooth. In the same section I presented the comparison of Bluetooth with other communication technologies. The main questions I hope to answer in this thesis and also discuss the methodology I employed. The subsequent sections discuss the core technical features and issues of security and interoperability of Bluetooth. In these sections I identify the key aspects of Bluetooth that make it standout from other wireless technologies and point out certain shortcomings of this technology. During this I went through different aspect of Bluetooth technology. Subsequently I present my analysis of the market player’s and user’s perspectives and identify the main drivers and barriers of Bluetooth from a business point of view. Towards the end of this thesis I discuss how this technology can be used to provide some attractive solutions. I demonstrate my ideas by discussing how certain services can be used in future in different scenarios. In my proposed solution I discussed the possibilities and advantages of using Bluetooth technology in university campus to perform different routine tasks and this will beneficial for the university both student and teachers. Keywords: Personal Area Networks, Asynchronous connection Link, Ultra Wide Band, Special Interest group, Bluetooth Technology / Malik Zaka Ullah Phone # 0092 301 8460404,0046738746534 Email : malikzakas@hotmail.com

Sensors have been an integral part of our life since a long time. Traditionally, the transmit information to a data collection center through a physical wire. However, with the introduction of Bluetooth Low Energy (BLE) communication protocol, more research is being done into the field of wireless sensor networks (WSN). BLE was introduced to target low power applications. The CC2650 Launchpad designed by Texas Instruments (TI) can lead to a bulky final product. The aim was to design hardware for the CC2650 micro-controller with the aim of making it more compact for use in WSNs. A top-down approach was used wherein the available product is studied to identify the redundant and reverse engineer it to design a new product. A 2 layer printed circuit board (PCB) was designed which resulted in a 64 percent decrease in size compared to the Launchpad. Also, experiments were performed to test the proof of concept.

The area of deterministic noise cancellation in mobile radio communication systems is investigated and analyzed. Several interoperation problems in the mobile wireless radio space are identified and interference concerns for the Bluetooth - WLAN networks are characterized and quantified in the physical layer. A mathematical framework has been created for describing interference in the 2.4 GHz band. An adaptive noise suppression system has been developed that is able to alleviate the encroachment of the aggressor signal on the victim without sacrificing any of the original signal. This system is demonstrated to improve the victim SNR in a spread spectrum communication scenario. The research is extended to construct an interference canceller that is easy to assimilate into existing RF front-ends. A low-power small form-factor analog active canceller has been designed in 0.18-ìm Si-CMOS IC technology that delivers adequate noise suppression performance while operating in the RF domain. This includes novel implementations of phase rotator circuits based on delay interpolation and an integrated low-current quadrature modulator-based continuously variable analog phase shifter. This canceller is capable of up to 30 dB of in-band cancellation for the Bluetooth - WLAN problem. Other versions of the canceller are configured to protect GPS and DVB-H receivers from unintentional radiators transmitting in the vicinity. These demonstrate noise mitigation of at least 15 dB in their respective bands while generating very low broadband noise at the output. A simple low-power mixed-signal automatic control mechanism is also developed to operate the canceller adaptively. The work described in this dissertation advances the state-of-the-art in the area of mobile wireless radio coexistence.

The emergence of portable terminals in work and living environments is accelerating the progression of wireless networks. A wireless ad hoc network is a new network concept where users establish peer-to-peer communication among themselves independently, in their small area. Since the wireless medium is a shared resource, it becomes an important design issue to efficiently allocate bandwidth among users. MAC (Medium Access Control) layer arbitrates the channel access to the wireless medium and is also responsible for bandwidth allocation to different users, therefore a large amount of research has been conducted on various MAC protocols for ad hoc wireless networks. This dissertation begins with a survey of existing wireless MAC protocols. The survey includes protocols designed for different network generations and topologies, classifying them based on architecture and mode of operation. Next, we concentrate on the MAC protocols proposed for distributed wireless networks. We propose a new MAC protocol based on a token-passing strategy; which not only incorporates the advantages of the guaranteed access scheme into the distributed type of wireless networks, but also the data rate and delay level QoS guarantees. Data rate QoS provides fairness into sharing of the channel, while delay level QoS introduces a flexible prioritized access to channels by adjusting transmission permission to the current network traffic activities. A simulation model for the protocol is developed and delay and throughput performance results are presented. To examine the efficiency and performance of the proposed MAC scheme in an ad hoc wireless environment, it is incorporated into the Bluetooth structured network. The model is then simulated in the Bluetooth environment and performance results are presented. Furthermore, an analytical model is proposed and an approximate delay analysis conducted for the proposed MAC scheme. Analytical results are derived and compared with results obtained from computer simulations. The dissertation concludes with suggestions for improvements and future work. / Thesis (M.Sc.-Engineering)-University of Natal, 2003.

Abstract available in digital copy. / Thesis (M.Sc.Eng.)-University of Natal, Durban, 2003.