Spelling suggestions: "subject:"molt preload"" "subject:"molt reload""
1 |
Simulation of vehicle impact into a steel building : A parametric study on the impacted column end-connectionsCravotta, Stefan, Grimolizzi, Emanuele January 2015 (has links)
Understanding the true behaviour of impacted structures is the only way to assess their robustness under exceptional events such as vehicle collision. The primary objective of this master’s thesis was to perform a finite element parametric investigation on the influence that some parameters have in steel buildings subjected to vehicle impacts. The parameters chosen for the study, involved uncertainties in the material definition and in the load configuration of the bolts used in the impacted column end-connections. By using the Abaqus software, a finite element model of the structure has been created. The five storey steel building considered has been modelled in a simplified manner with the exception of the impacted area which, instead, has been defined in a more detailed fashion. During the simulations, different preload conditions have been used, comparing cases with and without the preload force. Regardless its variation, it has not been observed any increase in the structural resistance. On the other hand, the simulation provided interesting results for what concerns the material variations in the bolts. Although the changes have been small in magnitude, the effect on the structural response during the impact was remarkable. For all the cases considered, an increase of the material ductility, achieved by increasing the ultimate strain at failure, entailed higher resistance of the connections. Various failure modes have been observed when the material properties have been changed. Having clarified the influence of the assumptions made, the results provided helpful information in sight of future studies. Although the model still needs to be validated, the research clarified which of the parameters investigated are to be collected with more attention. Keywords: Vehicle collision, steel building, FE model, Abaqus/Explicit, parametric investigation, bolt preload, bolt material.
|
2 |
Determination of stresses and forces acting on a Granulator knife by using FE simulationJames Aricatt, John, Velmurugan, Devarajan January 2015 (has links)
Recycling of plastics always plays an important role in keeping our environment better and safe. With the rise in usage of plastics and industrialization, the need for recycling the plastics has become a big business and is getting bigger. This thesis work was done for a company called Rapid Granulator AB, which works with the recycling of plastics as a big trade in Sweden. Like all the industries across the globe are trying to be economical in every way, Rapid Granulator AB wanted to develop an economical design of their high quality granulating knife. For achieving the economical design, they wanted to study the behaviour of the rotating knife during the process of producing plastic granules. The granulator cutting process was simulated and numerical analysis was done on the rotating knife of a plastic granulator machine by using the finite element code ABAQUS with 3D stress elements to find out the critical stresses and forces acting on the rotating knife. The bolt preload was applied by Abaqus/Standard, and the results of implicit analysis were imported to Abaqus/Explicit for the impact analysis where the flow of stresses on the rotating knife during the impact with materials were simulated and studied. The study was done on knife models of different thickness to see if the thickness of the current knife model can be reduced. Analysis were done also on a knife model assembly with a double sided cutting edge knife to see if the knife model can be used to its full extent. The simulation models and analysis results were given to the company to develop a more economical knife model.
|
3 |
A Novel Ultrasonic Method to Quantify Bolt TensionMartinez Garcia, Jairo Andres 01 January 2012 (has links)
The threaded fasteners are one of the most versatile methods for assembly of structural components. For example, in bridges large bolts are used to fix base columns and small bolts are used to support access ladders. Naturally not all bolts are critical for the operation of the structure. Fasteners loaded with small forces and present in large quantities do not receive the same treatment as the critical bolts. Typical maintenance operations such tension measurements, internal stress checking or monitoring of crack development are not practical due to cost and time constrains. Although failure of a single non-critical fastener is not a significant threat to the structure's stability, massive malfunction may cause structural problem such as insufficient stiffness or excessive vibrations.
The health of bolted joints is defined by a single parameter: the clamping force (CF). The CF is the force that holds the elements of the joint together. If the CF is too low, separation and bolt fatigue may occur. On the other hand, excessive CF may produce damages in the structural members such as excessive distortion or breakage. The CF is generated by the superposition of the individual tension of the bolts. The bolt tension, also referred as bolt preload, is the actual force that is stretching the bolt body. Maintaining the appropriate tension in bolts ensures a proper CF and hence a good health of the joint.
In this thesis, a novel methodology for estimating the tension in bolts using surface acoustic waves (SAWs) is investigated. The tension is estimated by using the reflection of SAWs created by the bolt head interference. Increments in the bolt tension raise the points of interaction between the waves and the bolt head (real area of contact), and hence the position of the reflective boundaries. The variations are estimated using the "conventional linear synthetic array" imaging technique. A singular transducer is actuated from predefined positions to produce an array of signals that are subsequently arranged and added to construct an acoustic image.
Three sets of experiment are presented in this research for validating the proposed concept: tension estimation of a ¼ inch stainless steel bolt, a ½ inch stainless steel bolt and ¼ inch grade 8 bolt. Acoustic images of the surface of the clamped plate illustrate a clear trend in the position of the reflective boundary when torque is changed. In all cases, the torque increments increase the real area of contact and therefore the position of the reflective boundary. As expected, the real area of contact grew from the bolt head center to the perimeter, which causes an effect of apparent movement of the boundary. This research proves the potential of the ultrasonic imaging methodology to measure applied tension. The result showed that the system can be used to successfully inspect tension in bolts of ½ and ¼ inches. The methodology investigated in this thesis is the first steps towards the development of bolt tension sensor based on surface acoustic waves.
|
Page generated in 0.0504 seconds