This study aims to investigate the effects of ventilation rate, indoor air temperature, humidity and using a heat recovery ventilation system on indoor radon concentration and distribution. Methods employed include energy dynamic and computational fluid dynamics simulation, experimental measurement and analytical investigations. Experimental investigations primarily utilize a continuous radon meter and a detached house equipped with a recovery heat exchanger unit. The results of the dynamic simulation show that the heat recovery unit is cost-effective for the cold Swedish climate and an energy saving of about 30 kWh per  floor area per year is possible, while it can be also used to lower radon level. The numerical results showed that ventilation rate and ventilation location have significant impacts on both radon content and distribution, whereas indoor air temperature only has a small effect on radon level and distribution and humidity has no impact on radon level but has a small impact on its distribution.

The use of Large Eddy Simulation (LES) for modelling air flows in buildings is a growing area of Computational Fluid Dynamics (CFD). Compared to traditional CFD techniques, LES provides a more detailed approach to modelling turbulence in air. This offers the potential for more accurate modelling of low energy natural ventilation which is notoriously difficult to model using traditional CFD. Currently, very little is known about the performance of LES for modelling natural ventilation, and its computational intensity makes its practical use on desk top computers prohibitive. The objective of this work was to apply LES to a variety of natural ventilation strategies and to compile guidelines for practitioners on its performance, including the trade-off between accuracy and cost.

Thesis (MEng)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: Modern Computational Fluid Dynamics modelling (CFD) are becoming common design and analysis tools in the engineering field. Nowadays, project designs involve the use of CFD techniques along with physical scale modelling to analyse the complex rapidly varied and turbulent flows which would not be easily analysed by physical modelling. In particular, the consideration and/or use of CFD modelling in the Hydraulic Engineering field remains on the increase. Apart from being used for comparison with other design techniques, CFD may in future become a standalone modelling technique in hydraulic structures design. This research aims to use CFD models to validate the simulation of the flow over two ogee dam spillways which are installed in the Hydraulic Laboratory of Stellenbosch University. To achieve this simulation of the flow which involves an interaction between water and air, the flow behaviour has been mapped by the Volume of Fluid (VOF) and the realisable "𝑘−𝜀" turbulence numerical models. The Volume of Fluid (VOF) and the realisable "𝑘−𝜀" models simulate the free surface of two-phase flow and the flow turbulence, respectively. Firstly, the study embarks with details on the actual design approaches of a typical ogee dam spillway. It subsequently presents the geometry and dimensions of the physical models, the testing procedure and the experimental test results achieved from this modelling exercise. For CFD modelling, a commercially available Computational Fluid Dynamics (CFD) package, Ansys-Fluent, was used. To model the physical model, the use of Reynolds-averaged Navier-Stokes equations in combination with the realisable k-ε eddy-viscosity closure model was adopted. The process of CFD model development and the underlying theory of it are discussed in this thesis. Different test scenarios including steady and fully hydrodynamic states simulation for two and three-dimensional geometries were considered in this simulation to achieve the most accurate results. In order to determine the required mesh size, the mesh sensitivity tests were conducted on the 2 dimensional and 3 dimensional models. Finally, the pressure readings and water levels produced by numerical models are discussed through a validation process by comparing the CFD model results with the results obtained from physical models. The outcome proved that CFD models are able to map the behaviour of both flow phases since they exhibited a close correlation to those achieved in the physical models. Even though some slight differences in values were revealed, the graphical trend remains reasonably similar for all test results. / AFRIKAANSE OPSOMMING: Moderne gerekenariseerde vloeidinamika numeriese modelle (CFD) word deesdae dikwels deur ingenieurs gebruik. Projekontwerpe sluit tans die gebruik van CFD tegnieke asook fisiese skaalmodellering in om komplekse, vinnig-veranderede en turbulente vloei te ontleed. Hierdie tipe vloeie is moeilik om met fisiese modellering te ontleed. Die gebruik van CFD numeriese modelle in hidrouliese ingenieurswese is besig om toe te neem, Die bevindinge van CFD modelering word tans vergelyk met die bevindinge van ander ontwerptegnieke, maar in die toekoms mag dit moontlik gebruik word as die enigste modelleringstegniek in hidrouliese struktuurontwerp. Die doel met hierdie navorsing is om CFD modelering te gebruik om die vloei oor twee ogee-vormige afvoergeute wat in die hidrouliese labrotorium van die Universiteit van Stellenbosch ge-installeer is, te ondersoek. Ten einde hierdie vloei, wat die interaksie tussen water en lug insluit, te simuleer, is die vloeigedrag deur ”volume van vloeistof” (VOF) en die "𝑘−𝜀" turbulensie numeriese modules, gemodeleer. Die VOF en "𝑘−𝜀" numeriese modules simuleer onderskeidelik die vry oppervlakte vloei van die twee-fase vloei en turbulente vloei. Die ontwerp van ’n tipiese ”ogee”-tipe dam oorloop word bespreek, gevolg deur die beskrywing van die geometrie van die fisiese modelle, die toetsprosedure en die eksperimentele toetsresultate. Vir die CFD modellering is die CFD pakket, Ansys-Fluent, gebruik. Vir die simulering van die fisiese model is die Reynolds-gemiddeld Navier-Stokes vergelykings tesame met die k-ε eddy-viskositeit geslote module gebruik. Die proses van CFD ontwikkeling en die onderliggende teorie daarvan word bespreek. Verskillende toets-scenario’s wat 2D en 3D simulasies insluit, uitgevoer. Ten einde die toepaslike berekeningsrooster grootte vir die numeriese model te verkry, is sensitiewiteitstoetse uitgevoer op die twee- en drie-dimensionele numeriese modelle. Laastens is die CFD numeries gesimuleerde drukke en die watervlakke met die van die fisiese modelle vergelyk om die akkuraatheid van die CFD resultate te verkry. Die uitkomstes het getoon dat CFD modelle gebruik kan word om die gedrag van albei vloei fases te simuleer aangesien dit goed vergelyk het met die uitkomstes van die fisiese modellering. Daar was wel klein verskille in die druk waardes, maar die tendense in drukverspreiding was ooreenstemmend.

We have studied gas flow and particle deposition in a realistic three-dimensional model of the bronchial tree, extending from the trachea to the segmental bronchi (7th airway generation for the most distal ones) using Computational Fluid Dynamics (CFD). The model is based on the morphometrical data of Horsfield et al. [J. Appl. Physiol., 31: 207-217, 1971] and on bronchoscopic and CT images, which give the spatial 3D-orientation of the curved ducts. It incorporates realistic angles of successive branching planes. Steady inspiratory flow varying between 50cm³/s and 500cm³/s was simulated as well as deposition of spherical aerosol particles (1 to 7 m diameter, 1g/cm³ density). Flow simulations indicated non-fully developed flows in the branches because of their relative short lengths. Velocity flow profiles in the segmental bronchi, taken one diameter downstream the bifurcation, were distorted compared with the flow in a simple curved tube, and wide patterns of secondary flow fields were observed. Both were due to the asymmetrical 3D configuration of the bifurcating network. Viscous pressure drop in the model was compared with results obtained by Pedley et al. [Respir Physiol, 9: 387-405, 1970], which are shown to be a good first approximation. Particle deposition increased with particle size and was minimal for approximately 200cm³/s inspiratory flow but it was highly heterogeneous for branches of the same generation.

Motivation Ce document synthétise un travail de quatre années relatif à l'étude des phénomènes dynamiques rencontrés dans une arme de petit calibre. Jusqu'à présent, des efforts ont été réalisés pour simuler des armes de gros calibre, avec plus ou moins de succès. L'adaptation directe de ces méthodes au petit calibre est, la plupart du temps, décevante car peu précise. De plus, le coût des essais en arme de petit calibre, relativement faible par rapport à des essais en armes de calibre plus important, a contribué au désintérêt des études dans ce domaine. Encore aujourd'hui, des fabriquants d'armes de renommée internationale ne disposent pas de modèles pour le petit calibre. Celui-ci a été, et reste encore aujourd'hui, le parent pauvre des simulations numériques en balistique intérieure. A l'heure actuelle, de nombreuses recherches sont entreprises dans le cadre des canons électriques ou électromagnétiques. Ces armes, qui représentent peut-être le futur de la balistique, ne sont encore qu'à un stade fort éloigné d'une utilisation effective et opérationnelle. La situation est donc assez paradoxale : les armes de petit calibre sont les plus utilisées (dans le cadre d'une utilisation militaire, sportive ou à des fins de tests) mais il n'existe, à proprement parler, que peu de modèles mathématiques permettant une simulation précise et rigoureuse. Dans ce contexte, ce travail va démontrer que des modèles de balistique intérieure peuvent être utilisés avec succès pour la simulation de tirs en armes de petit calibre. Une des originalités de ce travail consiste en l'utilisation d'un logiciel de CFD (Computational Fluid Dynamics} comme squelette d'un simulateur de la balistique intérieure, et à son application sur des armes de petit calibre. L'approche employée permet de dissocier les aspects "mécanique des fluides" et traitement de l'écoulement, des aspects purement balistiques. Nous nous attacherons donc à évaluer la capacité d'un code CFD à fonctionner dans l'environnement particulier de la simulation du "coup de canon". Plan du travail Cette thèse peut être subdivisée en quatre différentes parties. La première partie, plutôt générale, vise à situer le problème dans son contexte. Elle débute par une introduction rapide à la balistique, et s'attarde sur les buts de la balistique intérieure en mettant l'accent sur les particularités des armes de petit calibre, le cas échéant. La simulation sur ordinateur est un aspect important du problème qui doit nécessairement être mis en rapport avec des résultats réels. C'est pourquoi la chaîne de mesure utilisée classiquement en balistique, ainsi que les dispositifs expérimentaux employés pour obtenir des résultats de validation, sont brièvement présentés dans la deuxième partie. La troisième partie est axée sur les modèles. Nous présentons les principaux types de modèles que l'on peut retrouver en balistique intérieure. Les modèles à paramètres globaux et à paramètres locaux sont développés et nous formulons quelques remarques générales au sujet de l'état de l'art dans ce domaine, avant de nous interroger sur la problématique du choix d'un logiciel CFD adapté à l'utilisation visée. Nous présentons alors le logiciel choisi, et détaillons les modèles qu'il utilise pour tenir compte des particularités de la balistique intérieure. Le mouvement du projectile dans l'arme, la combustion et le traitement du problème diphasique sont notamment passés en revue et développés. Mobidic (Mobidic est l'acronyme de : MOdélisation Balistique Intérieure DIphasique Canon) est un logiciel français que nous avons obtenu vers la fin de cette étude. Ce logiciel est reconnu pour sa capacité à modéliser précisément les tirs en arme de moyen et gros calibre. Son fonctionnement et les modèles qu'il utilise sont exposés et comparés à notre implémentation. La quatrième et dernière partie n'est certainement pas la moins importante. Elle présente les résultats issus des tirs que nous avons réalisés et les différentes étapes de validation qui ont été menées à bien, depuis les tests de base jusqu'à la validation totale dans deux armes de petit calibre. Enfin, les conclusions, remarques et directions futures clôturent ce travail.

<p>The fiber suspensions in the production line from wood topaper are subjected to many types of chemical and mechanicalprocesses, in which the flow of the suspension is of vitalimportance. The flow of the suspension determines the degree ofuniformity of the fibers through the processing, which inreturn affects the properties of the fiber suspension. In orderto optimise the process, thorough knowledge of the suspensionflow is necessary, both on the level of suspension, fibernetworks and individual fibers. Knowledge of the fibersuspension behaviour combined with commercial CFD simulationprovides an efficient design method for any unit operation inthe papermaking process.</p><p>This work concentrates on macroscopic modeling of thebehaviour of fiber suspensions from 0.5-5% dry content, purefiber suspensions without fillers or additives. Any mechanismscausing the characteristic behaviour of the pulp suspensionhave not been included, they are only included through theirinfluence on the suspension parameters. Excluded mechanismsare, for instance, the fiber-fiber coupling mechanisms that arethe reason for the formation of fiber networks and parts offiber network, flocs.</p><p>By combining a rheology model for the bulk suspension, awall function that accounts for the slip layer and finallyintroducing turbulence, a model has been created that is ableto simulate the flow of most fiber suspensions. The flow of thesuspension is not constrained to any particular flowconditions; the models discussed in this work aim at describingthe behaviour of the suspension for all flow rates and flowtypes. The models are developed under simple flow conditions,where all variables can be controlled, but the models areintended for usage within the industry-based flows in real pulpand papermaking applications.</p><p><b>Keywords:</b>rheology, fiber, suspension, CFD, model, wall,slip, turbulence</p>

<p>This research presents the results of numerical study of heat transfer and pressure drop in a heat exchanger that is designed with different shape pin fins. The heat exchanger used for this research consists of a rectangular duct fitted with different shape pin fins, and is heated from the lower plate. The pin shape and the compact heat exchanger (CHE) configuration were numerically studied to maximize the heat transfer and minimize the pressure drop across the heat exchanger. A three dimensional finite volume based numerical model using FLUENT© was used to analyze the heat transfer characteristics of various pin fin heat exchangers. The simulation applied to estimate the heat transfer coefficient and pressure drop for a wide range of Reynolds numbers with different pin fins. Circular pin configuration variations included changes in pin spacing, axial pitch and pin height ratio. Rectangular and drop-shaped pin variations also included changes in length and aspect ratio. Correlations for Nusselt number and friction factor were developed. The optimum drop shaped pin array was shown to match the heat transfer rates obtained by the optimum circular pin configuration while incurring less than one third the specific fluid friction power losses. The data and conclusions of this study can be applied to the optimization of different heat exchangers which are used in industry, especially oil cooler in power transformers which are currently working with low cooling efficiency. It can also be used in the design of electronic components, turbine blade cooling or in other high heat flux dissipation applications requiring a low-profile, high area-density based micro-heat exchanger design. This study also shows that numerical models backed with experimental analysis can reduce both the time and money required to create and evaluate engineering concepts, especially those that deal with fluid flow and heat transfer. In the following chapters, first the problems which are encountered by power transformer suppliers are described. Then pin fin technology is studied with more details as a novel solution to the oil cooling problem. Some studies on behavior of power transformer coolers are also conducted to make their problems more clear. Available experimental data in the Iran Transfo company have been used for validation of these studies. They are presented as separated papers at the end of thesis. Finally the results of pin fin studies are presented and horizontal continuous casting (HCC) is explained as a manufacturing method for pin fins production. A separate paper which is based on experimental study on HCC is also included at the end of thesis.</p> / <p>Forskningen presenterad är ett resultat av en numerisk studie av värmeöverföring och tryckfall i en värmeväxlare designad med olika former av Kylflänsar. Värmeväxlaren består av ett rektangulärt kanal utrustat med olika former av Kylflänsar och är uppvärmd underifrån. Kylflänsar forma och den kompakta värmeväxlarens utformning är studerade numeriskt för att maximera värmeöverföringen och minimera tryckfallet över värmeväxlaren.En tredimensionell finit volym baserad på en numerisk modell i FLUENT© användes för att analysera värmeöverföringsegenskaper för olika Kylflänsar konfigurationer. Genom simuleringar uppskattades värmegenomgångstalet och tryckfallet för olika Reynolds tal och Kylflänsar konfigureringar. Cirkulära Kylflänsar konfigurationer inkluderar variation av avstånd mellan Kylflänsar, och förhållandet mellan axiellt avstånd och höjd. Rektangulära och droppformade Kylflänsar inkluderade även variation för längd och aspekt förhållande. Korrelation mellan Nusselts tal och friktionsfaktor utvecklades. Optimal matris för hur droppformade Kylflänsar placerades visades överensstämma med optimal överföring för cirkulära Kylflänsar men bara med en tredjedel av friktionsförlusterna för fluiden. Data och slutsatser från studien kan användas inom för optimering av värmeväxlare använda i industrin, speciellt oljekylda högspänningstransformatorer som har låg effektivitet i kylningen. Resultaten kan även användas inom design av elektronikkomponenter, kylning av turbinblad eller andra komponenter med högt värmeflöde där låg profil, och stor ytdensitet behövs. Studien visar att kombinationen av numeriska modeller som valideras genom experiment kan reducera både tid och kostnad vid utveckling och utvärdering av ingenjörsverktyg, speciellt inom fluidmekanik och värmeöverföring. I följande kapitel beskrivs först problem som identifierats av tillverkare av högspänningstransformatorer. Kylflänsar studeras i detalj som en ny lösning till de identifierade problemen med oljekylning. Några studier har genomförts för att ytterligare belysa problemen kring högspänningstransformatorers kylning. Tillgängliga data från Iran Transfo company har använts för validering av resultat från studierna. Studierna presenteras som separata artiklar i slutet av avhandlingen. Avslutningsvis presenteras resultat från studierna av Kylflänsar och en horisontell kontinuerlig gjutprocess (HCC) för tillverkning av Kylflänsar. HCC-studien presenteras som en separat artikel inkluderad sist i avhandlingen.</p>

Photovoltaic (PV) cells have long been an attractive alternative for the consumption of fossil fuels but current manufacturing practices suffer from poor energy efficiency, large carbon footprints, low material utilization, high processing temperatures and high solvent usage. A critical step in PV production is the deposition of CdS as a thin film to serve as a "buffer layer" between the optically absorbent layer and the transparent conducting oxide (TCO) layer to complete an effective p-n junction. The development of an inexpensive, low temperature, constant flow deposition process for producing CdS films is investigated. Micro-assisted solution concepts are implemented to promote the selectivity of heterogeneous surface reactions over homogeneous bulk precipitation. Analytical models based off Hagen-Poiseuille equation for fluid flow are coupled with computational fluid dynamic simulations to produce uniform flow fields within the deposition step permitting uniform film coverage on large substrates. / Graduation date: 2011 / Access restricted to the OSU Community at author's request from Jan. 11, 2011-Jan. 11, 2012.

McDonalds Lime Ltd, situated in Otorohanga, New Zealand, operate two dry process rotary lime kilns producing burnt and hydrated lime for a range of industries including agriculture, roading, water treatment, gold mining and steel making. The following Technology in Industry Fellowship (TIF) funded Masters Project is structured around investigating the combustion characteristics of Kiln Two at McDonald’s Lime Ltd using Computational Fluid Dynamics (CFD). Numerical results obtained using the commercial CFD code FLUENT were first validated against experimental data from the International Flame Research Foundation’s (IFRF) Furnace No.1. The validation study focussed on comparing the finite rate and mixture fraction/PDF approaches to combustion chemistry, as well as different methods for defining coal particle size distributions. Numerical modelling of Kiln Two at McDonald’s Lime Ltd began with full three-dimensional simulations, however due to their complexity and large computational times, two-dimensional axisymmetric models were primarily used for investigations. Comparisons were made between the two approaches. Investigations into the original pulverised coal fired system focussed on how the kiln aerodynamics and heat transfer properties were affected by changes to the coal and air inlet properties. The performance of a recently installed waste oil firing system was also investigated, with results showing that firing the kiln with a 25% thermal substitution of oil is the most efficient mode of operation. As the investigations focussed on the combustion characteristics the effects of the reacting limestone bed were ignored in all simulations. CFD modelling of the combustion characteristics within a large scale rotary kiln proved to be an extremely complex task. The work presented in this thesis has however provided some promising results which will ultimately assist McDonalds Lime Ltd in reducing their operating costs and environmental impact. Futhermore, the project has laid the foundation for further investigations.

This thesis investigates the application of CFD techniques to the aerodynamic analysis of a U-shaped JETC. Investigations were carried out to determine the flow patterns present at a number of locations within the structure of a full U-shaped JETC. The CFD solutions produced in these investigations used recommendations from the literature in the set-up of the CFD solver, and provided the computational component towards problem-specific validation of the CFD techniques used. A structured series of CFD-aided investigation and design processes were then performed. These processes were based around a series of analyses that evaluated the influence of a number of cell parameters in terms of cell airflow efficiency and velocity distortion. Four cell components; the inlet and exhaust stack baffle arrangements, the turning-vanes, the rear of the working section and augmenter entrance, and the lower exhaust stack, including the BB, were investigated in individual analyses. Throughout the investigations the value of CFD as a design tool was constantly assessed. Overall, the findings suggest that aerodynamic optimisation of the baffle arrangements would provide the greatest gains to cell airflow efficiency. As some cells contain as many as three baffle arrangements, the potential increases made to cell airflow capacity are sizable. Through implementing the findings of the baffle arrangement investigations, static pressure loss across the five-row baseline arrangement was reduced by 79%. For low levels of velocity distortion in the upstream region of the working section, the need to design the inlet stack baffles in the turning-vane arrangement was highlighted. Mid-baffle vane alignment, consistent flow channels, and sufficiently low chord to gap ratios should be incorporated into a turning-vane design to maximise flow uniformity. The need for the baffle and vane components to combine with the geometry of the cell to limit adverse pressure gradients was found as a requirement to minimise inner corner separation, and the downstream threat it creates to a safe testing environment. CFD proved to be a valuable analysis tool throughout the investigations performed in this thesis. The number of design iterations analysed, and the detail of data that could be extracted, significantly exceeded what could have been achieved through an isolated experimental testing programme.