No description available.

Thesis (MSc)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: Soil is one of the most complex and understudied terrestrial habitats, and it comprises a wide range of organisms that affect the functioning of terrestrial ecosystems. Despite the importance of these below-ground fauna, our understanding of this diversity remains limited, especially in the Cape Floristic Region (CFR), where higher plants and other more conspicuous invertebrates have been better represented in the literatures. The main aim of this thesis is to provide the first insights into the taxonomic, cryptic and spatial diversity of one of the more diverse Collembola genera, Seira (Collembola: Entomobryidae: Seirinae), in the Fynbos and Southern Afrotemperate forest habitats of the CFR. Collembola constitute an important component of terrestrial biodiversity and are essential for ecosystem functioning. The thesis is divided into two data chapters. The first data chapter examines the mitochondrial barcoding COI (Cytochrome-c oxidase subunit I) gene of 496 Seira specimens from 41 Fynbos and forest sites. Discrete Molecular Operational Taxonomic Units (MOTUs) are identified within Seira. Furthermore, divergence times are estimated and tentatively used to propose historical triggers for the diversification of Seira. Habitat specificity of Seira is assessed through phylogenetic reconstruction using Parsimony and Bayesian analyses based on the nucleotide and amino acid sequences. Genetic divergence indicates that Seira is composed of at least 91 MOTUs, suggesting that morphological taxonomy has vastly under-estimated the richness of this genus by at least four folds. Most of the MOTUs are highly habitat specific and geographically localised. The reconstruction of an evolutionary time frame of these lineages reveals several deep diversifications in the Miocene and a spate of more recent radiations in the Pleistocene and Holocene. Palaeo-environmental fluctuations and vegetation composition shifts are hypothesised as having increased the environmental complexity of the region and this may have influenced the diversification patterns of Seira. In the second data chapter, the spatial variation of Seira diversity is examined and compared between and within two major habitat types, Fynbos and forest, across nine study sites. Abiotic variables were recorded and compared for the investigation of environmental differences among habitat types. The habitat specificity of Seira is assessed, as well as the relative effects of habitat types and study sites on assemblage structure. Species richness of Seira is higher in Fynbos than in forest, and this could be due to the high heterogeneity of niches and resources created by the steep environmental and floristic gradients in the Fynbos habitats. Perhaps one of the most striking results is the high levels of beta diversity exhibited by Seira. The spatial turnover of the Seira assemblage is complete or nearly complete among and within habitat types across study sites within the CFR. Low dispersal abilities and consequently isolated evolutionary histories may account for the strong assemblage differences within the same habitat type of different study sites. However, the substantial differences in assemblage composition between adjacent habitat types in the same site are likely to be the result of the contrasting abiotic conditions exhibited by the Fynbos and forest habitats, as found by this study. Overall, the results of this thesis suggest that Seira species richness is much greater than previously thought. It follows similar diversity patterns to the well-described and hyper-diverse plant communities of the CFR. Here, for both CFR plants and Seira, the spectacular regional diversity displayed is not the result of high alpha diversity, but rather of substantial beta diversity. Because of the high beta diversity and the fact that only two CFR vegetation types were sampled from a limited number of study sites, I predict that the Seira species richness presented here is but the tip of the iceberg. / AFRIKAANSE OPSOMMING: Geen opsomming beskikbaar

Thesis (PhD)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: Understanding how divergent selection results in the evolution of reproductive isolation (i.e. speciation) is an important goal in evolutionary biology. Populations of herbivorous insects using different host plant species can experience divergent selection from multiple selective pressures which can rapidly lead to speciation. Restio leafhoppers are a group of herbivorous insect species occurring within the Cape Floristic Region (CFR) of South Africa. They are specialised on different plant species in the Restionaceae family. Throughout my thesis I investigated how bottom-up (i.e. plant chemistry/morphology of host plant species) and top-down (i.e. predation and competition) factors drive specialisation and divergence in restio leafhoppers. I also investigated interspecific competition as an important determinant of restio leafhopper community structure. In chapter 2 I quantified host specificity of restio leafhopper species within a local community for 24 months. I found that restio leafhopper species are highly host specific and potentially synchronised with the growth phases of their host plants. In chapter 3 I used a network metric, modularity, to determine whether host plant partitioning in a restio leafhopper community is non-random (i.e. driven by a deterministic process). This metric allows the identification of the components underlying host plant partitioning (modules). I then performed experiments to show that modules, and therefore host plant partitioning, can mostly be explained by preference and performance relationships (i.e. bottom-up factors). In chapter 4 I used null models to test whether niche partitioning in restio leafhopper communities is a general pattern across the landscape. I found non-random niche partitioning, which results from strong host specificity, in all investigated restio leafhopper communities. In addition, I performed binary host choice experiments in the presence and absence of interspecific competition, but found no evidence that interspecific competition narrows host preferences. These findings suggest that host specificity, the cause of niche partitioning, is likely shaped over evolutionary time. Sampling multiple interaction networks across the CFR, in chapter 5, I tested whether restio leafhopper populations are more host specific in species rich communities and regions in the CFR than in species poor communities and regions. I found no positive relationship between restio leafhopper species richness and host specificity at any scale. These findings suggest that specialisation is not driven by interspecific competition. In chapter 6 I investigated host shifts in Cephalelus uncinatus. C. uncinatus has a broader distribution than any single restio species that it can use; suggesting that host plant related divergence may result from geographic range expansion. I found that allopatric and parapatric populations, but not sympatric individuals, using different host plants have divergent host preferences. I also found evidence for morphological divergence in traits related to predator avoidance in population pairs that exhibit divergent host preferences. My findings emphasise the importance of both bottom-up and top-down factors, with the exception of interspecific competition, as determinants of specialisation and divergence in restio leafhoppers. I find no evidence that interspecific competition is an important force structuring restio leafhopper communities. Instead, strongly niche partitioned community structure appears to emerge from the speciation process. / AFRIKAANSE OPSOMMING: Die wyse waarop uiteenlopende seleksie lei tot die evolusie van seksuele isolasie (n.l. spesiasie) is ‘n belangrike vraag in evolutionêre biologie. Plantetende insekpopulasieses wat verskillende gasheerplante gebruik kan onder uinteenlopende veelvoudige seleksie wees en vinnig spesiasie ondergaan. Restio-blaarspringers is ‘n groep plantetende insekspesies wat gespesialiseerd is op verskillende plantspesies in die restio familie. In my tesis ondersoek ek die onder-op (n.l. plantchemie en morfologie) en bo-af seleksiekragte (n.l. predasie en kompetisie) wat lei tot gasheerspesialisasie en -spesiasie in restio-blaarspringers. Ek ondersoek ook die belangrikheid van tussen-spesieskompetisie in gemeenskapsorganisasie. In hoofstuk 2 het ek gasheerspesialisasie gekwantifiseer in ‘n klein restio-blaarspringergemeenskap oor 24 maande. Ek het gevind dat restio-blaarspringers hoogs gasheerspesifiek is en moontlik met die groeifase van hul hoofgasheerplante gesinchroniseerd is. Ek het in hoofstuk 3 ‘n netwerkmetriek, modulariteit, gebruik om te bepaal of restio-blaarspringers se gasheerverdeling nie-stokasties is (n.l. deur deterministiese prosesse veroorsaak is). Hierdie metriek laat ‘n mens toe om die komponente van gasheerverdeling (modules) te identifiseer. Deur middel van eksperimente het ek bepaal dat modules, en dus gasheerverdeling, deur gasheervoorkeur en prestasie (onder-op prossesse) verduidelik kan word. In hoofstuk 4 het ek ondersoek of gasheerverdeling algemeen is. Ek het deur middel van nulmodelle gewys dat gasheerverdeling algemeen is en veroorsaak is deur sterk gasheerspesifiekheid. Ek het ook voorkeureksperimente uitgevoer in die teenwoordigheid en afwesigheid van tussen-spesies kompetisie. Hier het ek geen teken gevind dat huidige tussen-spesies kompetisie gasheervoorkeur beïnvloed nie. My bevindinge in hierdie hoofstuk stel dus voor dat spesialisasie, die oorsaak van gasheerverdeling, oor evolutionêre tyd gevorm word. In hoofstuk 5 het ek ondersoek of populasies van restio-blaarspringers meer gasheerspesifiek is in restio-blaarspringerspesies ryke gemeenskappe en streke as populasies in spesies-arm gemeenskappe en streke. Ek het geen positiewe korrelasie tussen spesiesrykheid en gasheerspesialisasie gevind nie. Dit dui daarop aan dat gasheerspesialisasie, en dus gasheerverdeling, nie deur tussen-spesies kompetisie veroorsaak word nie. In hoofstuk 6 het ek gasheerplantgekoppelde divergensie ondersoek in Cephalelus uncinatus. C. uncinatus se verspreiding is breër as enige restio-spesies wat dit kan gebruik. Dit stel voor dat verspreidingvergroting gasheerverskuiwing mag veroorsaak. Ek het gevind dat populasies wat verskillende plante in allopatrie en parapatrie gebruik uiteenlopende gasheerkeuses maak, maar insekte wat verskillende plante in sympatrie gebruik wys nie ontwrigtende gasheerkeuses nie. Die populasies wat uiteenlopende gasheerkeuses getoon het, het ook verskillende morfologiese teen-predasie eienskappe getoon. Dit dui daarop aan dat predasie belangrik mag wees vir spesiasie in restio-blaarspringers. Die bevindinge van my tesis dui daarop aan dat beide onder-op en bo-af seleksie belangrik is vir gasheer-spesialisasie in divergensie. Nietemin, tussen-spesies kompetisie is nie ‘n belangrike bron vir spesialisasie, divergensie of gemeenskapsorganisasie nie. Gemeenskapsorganisasie is klaarblyklik slegs ‘n gevolg van die spesiasie proses.

Thesis (MSc)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: Only a limited number of systems involving anther-smut fungi have been studied, usually due to the economic significance of their crop plant hosts. A smut fungus of the genus Thecaphora has been discovered infecting Oxalis hosts in South Africa. This pathogenic fungus, Thecaphora capensis, produces dark-coloured spores in the anthers of host flowers, rendering it an anther-smut fungus. The host genus is the seventh largest plant genus in the Cape Floristic Region (CFR) and the largest geophytic genus of this region. Nine Oxalis species that host T. capensis have been identified across a wide distribution in the CFR of South Africa. A preliminary assessment of T. capensis infections of Oxalis was conducted in 2009, which provided a foundation for further research into the ecological and evolutionary consequences of hosting this fungus. In this study, a comprehensive host diversity assessment was conducted to determine the extent of infected Oxalis individuals within the CFR. Three new Oxalis host species for Thecaphora capensis were discovered. This brings the total number of known hosts to twelve. The morphological and reproductive effects of the fungus were assessed on two host species (O. incarnata and O. lanata) by comparing healthy and infected individuals of these species. Infection by Thecaphora capensis had a significantly negative effect on both of these factors. Host resources appear to be co-opted for fungal spore production, since floral morphological characters of infected individuals were reduced in size. Furthermore, infection by T. capensis ensured near-universal sterility in both hosts. Differences in floral characters and pollinator preferences for healthy Oxalis incarnata and O. lanata individuals from disease-free and diseased populations were compared to determine the evolutionary influence of Thecaphora capensis infections. It was shown that this pathogen can have a significant evolutionary influence on its hosts, showing its ability to shape flower size and pollinator activity in O. lanata, but not in O. incarnata. A need has therefore been identified to assess these evolutionary forces independently for each host and its pathogen before making erroneous assumptions for conservation practices. Plant pollinators play an integral role in plant fitness. Pollinator movements within a population are important when between-flower spore transfer by pollinators increases the likelihood of new infections. Pollinator movements may be influenced by host density and the frequency of diseased individuals, amongst other factors. Pollinators were found to mediate Thecaphora capensis spore transfers within diseased Oxalis populations. Host density and disease frequency affected the number of spores transferred under field and standardized conditions. More research is required to investigate confounding factors in these complex systems. This study highlighted the complexities of a fungal-plant-insect relationship, the evolutionary consequences of such fungal infections and the various factors influencing the likelihood of new infections. This research adds to the limited body of knowledge on multi-organismal interactions in the CFR and provides a base for more detailed future studies on this intriguing system. / AFRIKAANSE OPSOMMING: 'n Brandswam, wat deel is van die Thecaphora genus,is ontdek in 'n Oxalis blom waar dit die gasheer plant se blom gebruik om spore in te produseer. Die swam, Thecaphora capensis, produseer donker gekleurde spore in die helmknoppe van die blomme van gasheer plante, daarom word dit geklasifiseer as 'n brandswam van die helmknop. Die gasheer plante van die swam is deel van die genus Oxalis, die sewende grootste plant genus in die Kaapse Floristiese Streek (KFS) en die grootste geofitiese genus in die streek. Nege Oxalis species is al klaar identifiseer as gasheer plante van T. capensis. Hulle is versprei oor 'n groot area van die KFS van Suid Afrika. 'n Primêre ondersoek van T. capensis infeksies op Oxalis is in 2009 onderneem. Hierdie ondersoek het gelei tot meer vrae oor die sisteem en het 'n goeie fondasie geskep vir verdere navorsing rakende die ekologiese koste verbonde daaraan om as gasheer plant vir 'n swam op te tree. 'n Deeglike ondersoek is in die KFS aangepak om die Oxalis gasheer plante van die brand swam te identifiseer en om voort te bou op die basiskennis wat in die primêre ondersoek daargestel is. Drie nuwe Oxalis gasheer plante van Thecaphora capensis is ontdek. Die totale aantal gasheer plante staan nou op twaalf. Gesonde en geinfekteerde individuele gasheer plante is gebruik om die morfologiese en reproduktiewe effekte van die swam te toets in twee Oxalis spesies (O. incarnata en O. lanata). Die negatiewe gevolge om 'n gasheer plant van die brand swam te wees was duidelik toe gesonde en geinfekteerde individuele met mekaar vergelyk is. Dit kom voor asof gasheer plante se hulpbronne vir spoor produksie gebruik word, want hulle is morfologies kleiner en meestal steriel. Die evolusionêre effek van Thecaphora capensis op 'n populasie is getoets met gesonde individuele in populasies van twee Oxalis spesies. Blomkenmerke en insek bestuiwers van gesonde individue in gesonde en geinfekteerde populasies is ondersoek om die effekte van T. capensis op populasies te toets. Daar is suksesvol gedemonstreer dat swamme sterk evolusionêre kragte uitoefen, en die vermoë het om plantpopulasies te vorm en te verander, ofskoon nie in alle gevalle ewe sterk nie. Daarom is dit belangrik om die evolusionêre kragte vir elke gasheer plant en sy patogeen onafhanklik te assesseer, sonder om algemene aannames te maak in bewaringspraktyke. Plantbestuiwers speel 'n belangrike rol in die fiksheid van plante. Hulle kan hul fiksheid verbeter deur bestuiwers te lok met blomme en deur aspekte geassosieer met blomme. Die bewegingspatrone van plantbestuiwers is baie belangrik indien hulle helmknop-geproduseerde spore van brandswamme vervoer instede van stuifmeel, want dit vergroot die kanse vir nuwe infeksies. Die bewegingspatrone van plantbestuiwers word, onder andere, beinvloed deur die digtheid en frekwensie van geinfekteerde individue. Plantbestuiwers speel 'n belangrike rol in die vervoer van Thecaphora capensis spore in geinfekteerde Oxalis populasies. Die digtheid en frekwensie van geinfekteerde blomme het die vervoer van spore geaffekteer onder veld en gestandardiseerde kondisies, alhoewel baie veranderlikes so 'n komplekse natuurlike sisteem beinvloed. Hierdie studie beklemtoon die kompleksiteit van 'n fungus-plant-insek verhouding, die gevolge van so 'n interaksie en die verskeie faktore wat die waarskynlikheid van nuwe infeksies beinvloed. Tot dusver is daar 'n beperkte aantal sisteme soos hierdie bestudeer waarin 'n brandswam van die helmknop betrokke is, en die enkele beskikbare studies is onderneem meestal as gevolg van hulle ekonomiese effekte op landboukundig belangrike gasheer plante. Hierdie studie verteenwoordig 'n belangrike byvoeging tot die inter-organismiese studies in die KFS. 'n Holistiese ekologiese oorsig soos hierdie verskaf 'n belangrike basis vir toekomstige studies en bewarings- en bestuurspraktyke.

The natural hip joint in healthy people has a very low friction with very little (or no) wear. It works as a dynamically loaded bearing and is subjected to about 1-2 million cycles of loading per year. The applied load is the body weight which is tripled when walking and even higher during other activities such as running and jumping. Unfortunately these joints are not always healthy due to various causes such as fractures or disease leading to severe pain which necessitates joint replacement. Currently, the orthopaedic industries are working towards developing an ideal artificial hip joint with low wear, low friction, good lubrication, better fixation/stability and biocompatibility. Many different designs and materials have been investigated with some promising new implants which can be used depending on patients' individual need (large or small joint), activity and age. In this work, two types of artificial hip joints were tested for friction and lubrication studies: Metal-on-Metal (MoM) Biomet hip resurfacing ReCaps with large diameters (>35-60 mm) and different diametral clearances (~ 60-350 µm), and Zirconia Toughened Alumina (ZTA) heads against carbon-fibre-reinforced poly-ether-ether ketone (CFR PEEK) cups with different diameters (>35-60 mm) and diametral clearances (60-1860 µm). Seven serum-based lubricants with different viscosities were used with and without carboxy methyl cellulose (CMC) additions as gelling agent to increase viscosity depending on the CMC content. The maximum load applied was 2000 N for the stance phase with a minimum load of 100 N for the swing phase. A Pro-Sim friction hip simulator was used to investigate the frictional torque generated between the articulating surfaces so as the friction factor can be calculated. Stribeck analysis was then employed to assess the mode of lubrication. For the metal-on-metal hip resurfacing joints, the friction factors were in the range 0.03-0.151 and those for the ZTA ceramic heads versus CFR PEEK cups were in the range 0.006-0.32. Stribeck analyses showed mainly mixed lubrication for both MoM and ZTA ceramic-on-CFR PEEK joints. The experimental results were in agreement with most of the theoretical calculations suggesting mixed lubricating regimes at low viscosities and moving on to fluid film lubrication at higher viscosities. Joints with larger-diameters, lower clearances and lower surface roughness exhibited a higher lambda ratio suggesting improved lubrication. Viscosity flow curves for the serum-based lubricants having viscosity ≤ 0.00524 Pas showed non-linear relationship between viscosity and shear rate indicating non-Newtonian flow with pseudoplastic or shear-thinning characteristic, i.e. viscosity decreased as shear rate increased up to shear rates of ~ 1000 s⁻¹. However, at shear rates greater than 1000 s⁻¹ Newtonian flow became dominant with almost constant viscosity, i.e. a linear relationship between shear stress and shear rate. On the other hand, viscosity flow curves for the lubricants with viscosity ≥ 0.0128 Pas showed non-Newtonian behaviour up to a shear rate of 3000 s⁻¹ with shear-thinning characteristic.

Total hip joint prostheses made of CoCrMo heads versus ultra high molecular weight polyethylene (UHMWPE) cups have a limited lifetime, mainly due to the wear of the UHMWPE cups as a result of high friction between the articulating surfaces leading to osteolysis and implant loosening with revision surgery becoming inevitable in more active patients. Tribology plays an important role in developing the design, minimizing wear and reducing friction of hip joint prostheses in order to improve their long-term performance, with good lubricating properties. Metal-on-metal hip resurfacing prostheses have shown significantly lower wear rates compared with conventional metal-on-polyethylene implants and thus osteolysis is potentially reduced leading to increased lifetime of the prosthesis. Nevertheless, excessive wear of metal-on-metal joints leads to metal ion release, causing pseudo-tumours and osteolysis. An alternative approach to such bearings is the use of newly developed carbon fiber-reinforced poly-ether-ether-ketone (CFR PEEK) acetabular cups articulating against ceramic femoral heads due to their better wear resistance compared to UHMWPE. In this study, therefore, friction and lubrication properties of large diameter, as cast, Co-Cr-Mo metal-on-metal hip resurfacing implants with various diameters and clearances have been investigated and compared to those of the newly developed zirconia toughened alumina (ZTA) ceramic femoral heads articulating against carbon fiber reinforced poly-ether-ether-ketone (CFR PEEK) acetabular cups with different diameters and clearances. Friction hip simulator was used to measure frictional torque and then friction factors were calculated along with Sommerfeld numbers leading to Stribeck analysis and hence the lubricating mode was also investigated. This involved using lubricants based on pure bovine serum (BS) and diluted bovine serum (25 vol. %BS+75 vol. %distilled water) with and without carboxymethyl cellulose (CMC) (as gelling agent). Standard Rheometer was used to measure lubricant viscosity ranged from 0.0014 to 0.236 Pas at a shear rate of 3000 . Pure bovine serum, diluted bovine serum without CMC and with CMC (25BS+75DW+0.5gCMC and +1gCMC) showed pseudoplastic flow behaviour up to shear rate of ~139 s⁻¹ above which a Newtonian flow with significant increase in shear stress was observed. The viscosity flow curves for the 25BS+75DW+2gCMC, +3.5gCMC and +5gCMC showed only shear thinning up to a shear rate of 3000 . The shear rate application modified the flow behaviour of bovine serum from a pseudoplastic to a Newtonian flow depending on its purity and CMC content. This will cause a different frictional behaviour depending on joint diameter and clearance, as seen in this work. The experimental data were compared with theoretical iv predictions of the lubricating regimes by calculating theoretical film thickness and lambda ratio. The metal-on-metal Biomet ReCaps showed similar trends of Stribeck curves, i.e. friction factors decreased from ~0.12 to ~0.05 as Sommerfeld numbers increased in the range of viscosities ~0.001-0.04Pas indicating mixed lubrication regimes above which the friction factor increased to ~0.13 at a viscosity of 0.236Pas. The Stribeck analyses suggested mixed lubrication as the dominant mode with the lowest friction factor in the range ~0.09 - ~0.05 at the physiological viscosities of ~0.01 to ~0.04 Pas and that such joints can be used for more active patients as compared to the conventional total hip replacement joints with 28mm diameter. The Stribeck curves for all ZTA ceramic-on-CFR PEEK components illustrated a similar trend with BS fluids showing higher friction factors (in the range 0.22-0.13) than the diluted BS+CMC fluids (in the range 0.24-0.05). The friction tests revealed boundary-mixed lubrication regimes for the ZTA ceramic-on-CFR-PEEK joints. The results, so far, are promising and suggest clearly that the newly developed ZTA ceramic femoral heads articulating against CFR PEEK cups have similar friction and lubrication behaviour at optimum clearances to those of currently used metal-onmetal hip resurfacing implants at the range of viscosities 0.00612 to 0.155Pas. These results clearly suggest that the ZTA ceramic-on-CFR-PEEK joints showed low friction at the physiological viscosities of ~0.01Pas in the range ~0.1-0.05, suggesting that these novel joints may be used as an alternative material choice for the reduction of osteolysis. The result of this investigation has suggested that the optimum clearance for the 52mm diameter MOM Biomet ReCaps could be ~170μm. However, 48 and 54mm joints showed lower friction due to clearances to be >200μm. For the 52mm ZTA ceramic-on-CFR-PEEK joints the optimum clearance seems to be ≥ 630μm radial clearance. These results suggested that increased clearance bearings have the potential to generate low friction and hence no risk of micro- or even macro-motion for the ceramic-on-CFR-PEEK joints. This study found no correlation between theoretical predictions and experimental data for all metal-onmetal and ZTA ceramic-on-CFR PEEK bearings at the physiological viscosity (0.0127Pas). However, at lubricant viscosity of 0.00157Pas, the theoretical prediction of lubrication regime correlated well with the experimental data, both illustrating boundary lubrication. As expected, a decrease in viscosity resulted decrease in the film thickness.

The aim of this study was to investigate the development of release from proactive interference (RPI) and its relations with executive working memory functions. 101 primary school children (aged 6-12 years) and 20 young adults (aged 22-30 years) participated in the study. The main task, the Categorical Free Recall Test, comprised 12 items from 3 different categories (animals, fruits, clothes). The purpose of the main task was to examine both the development of the RPI pattern and the categorization ability during childhood. As our results showed, the categorization ability and the RPI pattern were already present in the 1st graders. Although overall memory span increased with age, there was no significant development for the categorization and the RPI effect. For the additional tasks, the Word Span Test (WST, to measure the phonological WM capacity), the Wisconsin Card Sorting Test (WCST, to measure both the categorization ability and executive WM functions), and the Listening Span Test (LST, to examine executive and complex WM functions), the results indicated that children also improved with age. Overall memory capacity in the main task was best predicted by the WST / however, memory of serial position was best predicted by the LST. These findings are in accordance with the view that the WST measures the phonological working memory span, whereas the LST measures complex working memory and executive functions. The comparisons between the adult and the child sample revealed that except for the RPI pattern adults were better on all tasks than the children. The lack of a consistent RPI pattern for the adults may be due to the relatively short stimulus list.

Total hip joint prostheses made of CoCrMo heads versus ultra high molecular weight polyethylene (UHMWPE) cups have a limited lifetime, mainly due to the wear of the UHMWPE cups as a result of high friction between the articulating surfaces leading to osteolysis and implant loosening with revision surgery becoming inevitable in more active patients. Tribology plays an important role in developing the design, minimizing wear and reducing friction of hip joint prostheses in order to improve their long-term performance, with good lubricating properties. Metal-on-metal hip resurfacing prostheses have shown significantly lower wear rates compared with conventional metal-on-polyethylene implants and thus osteolysis is potentially reduced leading to increased lifetime of the prosthesis. Nevertheless, excessive wear of metal-on-metal joints leads to metal ion release, causing pseudo-tumours and osteolysis. An alternative approach to such bearings is the use of newly developed carbon fiber-reinforced poly-ether-ether-ketone (CFR PEEK) acetabular cups articulating against ceramic femoral heads due to their better wear resistance compared to UHMWPE. In this study, therefore, friction and lubrication properties of large diameter, as cast, Co-Cr-Mo metal-on-metal hip resurfacing implants with various diameters and clearances have been investigated and compared to those of the newly developed zirconia toughened alumina (ZTA) ceramic femoral heads articulating against carbon fiber reinforced poly-ether-ether-ketone (CFR PEEK) acetabular cups with different diameters and clearances. Friction hip simulator was used to measure frictional torque and then friction factors were calculated along with Sommerfeld numbers leading to Stribeck analysis and hence the lubricating mode was also investigated. This involved using lubricants based on pure bovine serum (BS) and diluted bovine serum (25 vol. %BS+75 vol. %distilled water) with and without carboxymethyl cellulose (CMC) (as gelling agent). Standard Rheometer was used to measure lubricant viscosity ranged from 0.0014 to 0.236 Pas at a shear rate of 3000 . Pure bovine serum, diluted bovine serum without CMC and with CMC (25BS+75DW+0.5gCMC and +1gCMC) showed pseudoplastic flow behaviour up to shear rate of ¿139 above which a Newtonian flow with significant increase in shear stress was observed. The viscosity flow curves for the 25BS+75DW+2gCMC, +3.5gCMC and +5gCMC showed only shear thinning up to a shear rate of 3000 . The shear rate application modified the flow behaviour of bovine serum from a pseudoplastic to a Newtonian flow depending on its purity and CMC content. This will cause a different frictional behaviour depending on joint diameter and clearance, as seen in this work. The experimental data were compared with theoretical iv predictions of the lubricating regimes by calculating theoretical film thickness and lambda ratio. The metal-on-metal Biomet ReCaps showed similar trends of Stribeck curves, i.e. friction factors decreased from ~0.12 to ~0.05 as Sommerfeld numbers increased in the range of viscosities ~0.001-0.04Pas indicating mixed lubrication regimes above which the friction factor increased to ~0.13 at a viscosity of 0.236Pas. The Stribeck analyses suggested mixed lubrication as the dominant mode with the lowest friction factor in the range ~0.09 - ~0.05 at the physiological viscosities of ~0.01 to ~0.04 Pas and that such joints can be used for more active patients as compared to the conventional total hip replacement joints with 28mm diameter. The Stribeck curves for all ZTA ceramic-on-CFR PEEK components illustrated a similar trend with BS fluids showing higher friction factors (in the range 0.22-0.13) than the diluted BS+CMC fluids (in the range 0.24-0.05). The friction tests revealed boundary-mixed lubrication regimes for the ZTA ceramic-on-CFR-PEEK joints. The results, so far, are promising and suggest clearly that the newly developed ZTA ceramic femoral heads articulating against CFR PEEK cups have similar friction and lubrication behaviour at optimum clearances to those of currently used metal-onmetal hip resurfacing implants at the range of viscosities 0.00612 to 0.155Pas. These results clearly suggest that the ZTA ceramic-on-CFR-PEEK joints showed low friction at the physiological viscosities of ~0.01Pas in the range ~0.1-0.05, suggesting that these novel joints may be used as an alternative material choice for the reduction of osteolysis. The result of this investigation has suggested that the optimum clearance for the 52mm diameter MOM Biomet ReCaps could be ~170¿m. However, 48 and 54mm joints showed lower friction due to clearances to be >200¿m. For the 52mm ZTA ceramic-on-CFR-PEEK joints the optimum clearance seems to be ¿ 630¿m radial clearance. These results suggested that increased clearance bearings have the potential to generate low friction and hence no risk of micro- or even macro-motion for the ceramic-on-CFR-PEEK joints. This study found no correlation between theoretical predictions and experimental data for all metal-onmetal and ZTA ceramic-on-CFR PEEK bearings at the physiological viscosity (0.0127Pas). However, at lubricant viscosity of 0.00157Pas, the theoretical prediction of lubrication regime correlated well with the experimental data, both illustrating boundary lubrication. As expected, a decrease in viscosity resulted decrease in the film thickness.

The natural hip joint in healthy people has a very low friction with very little (or no) wear. It works as a dynamically loaded bearing and is subjected to about 1-2 million cycles of loading per year. The applied load is the body weight which is tripled when walking and even higher during other activities such as running and jumping. Unfortunately these joints are not always healthy due to various causes such as fractures or disease leading to severe pain which necessitates joint replacement. Currently, the orthopaedic industries are working towards developing an ideal artificial hip joint with low wear, low friction, good lubrication, better fixation/stability and biocompatibility. Many different designs and materials have been investigated with some promising new implants which can be used depending on patients¿ individual need (large or small joint), activity and age. In this work, two types of artificial hip joints were tested for friction and lubrication studies: Metal-on-Metal (MoM) Biomet hip resurfacing ReCaps with large diameters (>35-60 mm) and different diametral clearances (~ 60-350 µm), and Zirconia Toughened Alumina (ZTA) heads against carbon-fibre-reinforced poly-ether-ether ketone (CFR PEEK) cups with different diameters (>35-60 mm) and diametral clearances (60-1860 µm). Seven serum-based lubricants with different viscosities were used with and without carboxy methyl cellulose (CMC) additions as gelling agent to increase viscosity depending on the CMC content. The maximum load applied was 2000 N for the stance phase with a minimum load of 100 N for the swing phase. A Pro-Sim friction hip simulator was used to investigate the frictional torque generated between the articulating surfaces so as the friction factor can be calculated. Stribeck analysis was then employed to assess the mode of lubrication. For the metal-on-metal hip resurfacing joints, the friction factors were in the range 0.03-0.151 and those for the ZTA ceramic heads versus CFR PEEK cups were in the range 0.006-0.32. Stribeck analyses showed mainly mixed lubrication for both MoM and ZTA ceramic-on-CFR PEEK joints. The experimental results were in agreement with most of the theoretical calculations suggesting mixed lubricating regimes at low viscosities and moving on to fluid film lubrication at higher viscosities. Joints with larger-diameters, lower clearances and lower surface roughness exhibited a higher lambda ratio suggesting improved lubrication. Viscosity flow curves for the serum-based lubricants having viscosity ¿ 0.00524 Pas showed non-linear relationship between viscosity and shear rate indicating non-Newtonian flow with pseudoplastic or shear-thinning characteristic, i.e. viscosity decreased as shear rate increased up to shear rates of ~ 1000 s-1. However, at shear rates greater than 1000 s-1 Newtonian flow became dominant with almost constant viscosity, i.e. a linear relationship between shear stress and shear rate. On the other hand, viscosity flow curves for the lubricants with viscosity ¿ 0.0128 Pas showed non-Newtonian behaviour up to a shear rate of 3000 s-1 with shear-thinning characteristic. / Ministry of Higher Education, Libya

Biodiversity considerations form an essential component of Environmental Impact Assessment (EIA), especially in areas with both a high biodiversity value and development pressure such as the Cape Floristic Region (CFR) in South Africa. Limited research has been conducted within the South African context on the quality of biodiversity inputs to EIA. The aim of this research was to evaluate the quality of biodiversity input to EIA in the CFR. To address this aim, a customised review package was generated to evaluate the quality of 26 Biodiversity Impact Assessment (BIA) reports in the CFR. The results were then compared with international trends of biodiversity input to EIA in order to show how prevalent such trends are within an area with high biodiversity value. This comparison showed that the quality of biodiversity input to EIA in the CFR generally concur with inadequacies identified in international EIA literature. Typically, significant weaknesses identified during the review were the lack of public participation and an insufficient evaluation of alternatives. Specialists also failed to develop adequate monitoring programmes. Furthermore, a very pertinent limitation was that, in general, assessments are conducted during inappropriate seasons and over insufficient time periods. However, some variations to the international trends are also present within the Region. For example, a particular strength was that a precautionary approach was adopted by most of the specialists to avoid negative impacts on biodiversity. In addition, specialists did not merely focus on lower levels (species and habitats) of biodiversity, but incorporated ecological processes in assessment techniques. The inadequacies identified in this dissertation pose particular challenges for biodiversity management and conservation practices. The development and implementation of mechanisms such as Best Practice Guidelines and improved biodiversity related legislation is proposed to improve biodiversity input to EIA. / M Environmental Management, North-West University, Potchefstroom Campus, 2014