This work aims to study the variation in electrical and optical properties of nanoscale Schottky diodes by varying their dimensions in the nanoscale. Experimental conditions for fabricating porous alumina with varying pore diameters and inter-pore distances were first optimized by anodizing Aluminum tape with variable currents. Cadmium Sulfide nanowires were then synthesized inside the membranes by dc electrodeposition. Finally a high work function metal was deposited on top as a contact for the metal-semiconductor Schottky diode junction. As a comparative study, Schottky diodes fabricated using the same metals and Cadmium Sulfide thin films deposited on conducting glass substrates using electro-deposition and annealed in different ambient were also studied. Device characterizations were carried out by field-emission scanning electron microscopy (FESEM), current voltage (I-V) measurements, ultraviolet-visual (UV-Vis) absorption spectroscopy and X-Ray diffraction.

This work focuses on the solar cell based on the heterostructure formed between Copper Phthalocyanine (CuPc) and Cadmium Sulfide (CdS). Two different fabrication techniques were used for depositing the organic and inorganic layers of CuPc and CdS layers respectively. CuPc was deposited by electrodeposition while CdS was deposited by chemical bath deposition. Hybrid CdS/CuPc thin films were obtained from CdS films grown on Glass/ITO by chemical bath deposition followed by electrodeposition of CuPc onto these films and annealing at 250˚C after the deposition of each layer. The maximum open circuit voltage (Voc) and the short circuit current density (Jsc) obtained for this heterojunction solar cell are 0.59v and 0.7mA/cm2 respectively and these are the highest values achieved in literature till date. The materials characteristics and electrical performances of the device were analyzed. The effect of increasing the thickness of CuPc and CdS on the short circuit current density and open circuit voltage were also investigated.

Orientador: Victor Ciro Solano Reynoso / Banca: Keizo Yukimitu / Banca: Raul Fernando Cuevas Rojas / Resumo: O presente trabalho visou a produção e o estudo das propriedades físicas de amostras de resina epóxi transparente dopadas com diferentes concentrações de nanocristais de sulfeto de cádmio (CdS). As técnicas de difração de raios-X, espectroscopia no infravermelho, espectroscopia Raman e calorimetria diferencial de varredura (DSC) foram utilizadas para estudar as propriedades estruturais. Espectroscopias de refletância e de transmitância foram utilizadas para obter a dispersão do índice de refração e do coeficiente de extinção na região do UV-Vis para amostras dopadas com diferentes concentrações de CdS. A técnica do ângulo de Brewster foi também utilizada para determinar o índice de refração das diferentes amostras. Os valores dos índices de refração obtidos através das medidas de refletância e de transmitância na região do UV-Vis e da técnica do ângulo de Brewster foram comparados e os resultados mostraram que a técnica do ângulo de Brewster além de apresentar valores que conferem com a literatura apresentou valores com alta precisão. Foram realizadas medidas de birrefringência opticamente. Foram obtidos resultados da birrefringência fotoinduzida por um fóton para diferentes concentrações de CdS por amostra e para diferentes intensidades da luz de excitação. Os resultados foram quantificados utilizando alguns dos principais modelos teóricos, onde foi observado que a resina epóxi pura apresenta birrefringência fotoinduzida e a adição do CdS contribui para o aumento da birrefringência. / Abstract: The present work sought production and study of the physical properties of samples of transparent epoxy resin doped with different concentrations of structures of cadmium sulfide (CdS) nanocrystals. X-ray diffraction, infrared spectroscopy, Raman spectroscopy e differential scanning calorimetry techniques were used to study their structural properties. Reflectance and transmittance spectroscopy were used to obtain of the refraction index and of the extinction coefficients dispersion in the UVVis region for doped samples with different concentrations of CdS. The Brewster angle technique also was used to determine the refraction index of the different samples. The refraction index values obtained using the reflectance and transmittance measurement in the UV-Vis region and Brewster angle technique were compared and the results showed that the Brewster angle technique besides presents values that check with the literature, presented values with high precision. Measurements of optically induced birefringence were accomplished. Were obtained results of the photo induced birefringence by a photon for different concentrations of CdS for sample and for different intensities of the excitement light. The results were quantified using some of the principal theoretical models, where was observed that the pure epoxy resin presents photo induced birefringence and the addition of the CdS contributes to the increase of the birefringence. / Mestre

Made available in DSpace on 2014-06-11T19:25:33Z (GMT). No. of bitstreams: 0 Previous issue date: 2009-07-23Bitstream added on 2014-06-13T19:32:46Z : No. of bitstreams: 1 silveira_jb_me_ilha.pdf: 1625672 bytes, checksum: 5fb649c1f1320fe8b2df5942ab03558b (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / O presente trabalho visou a produção e o estudo das propriedades físicas de amostras de resina epóxi transparente dopadas com diferentes concentrações de nanocristais de sulfeto de cádmio (CdS). As técnicas de difração de raios-X, espectroscopia no infravermelho, espectroscopia Raman e calorimetria diferencial de varredura (DSC) foram utilizadas para estudar as propriedades estruturais. Espectroscopias de refletância e de transmitância foram utilizadas para obter a dispersão do índice de refração e do coeficiente de extinção na região do UV-Vis para amostras dopadas com diferentes concentrações de CdS. A técnica do ângulo de Brewster foi também utilizada para determinar o índice de refração das diferentes amostras. Os valores dos índices de refração obtidos através das medidas de refletância e de transmitância na região do UV-Vis e da técnica do ângulo de Brewster foram comparados e os resultados mostraram que a técnica do ângulo de Brewster além de apresentar valores que conferem com a literatura apresentou valores com alta precisão. Foram realizadas medidas de birrefringência opticamente. Foram obtidos resultados da birrefringência fotoinduzida por um fóton para diferentes concentrações de CdS por amostra e para diferentes intensidades da luz de excitação. Os resultados foram quantificados utilizando alguns dos principais modelos teóricos, onde foi observado que a resina epóxi pura apresenta birrefringência fotoinduzida e a adição do CdS contribui para o aumento da birrefringência. / The present work sought production and study of the physical properties of samples of transparent epoxy resin doped with different concentrations of structures of cadmium sulfide (CdS) nanocrystals. X-ray diffraction, infrared spectroscopy, Raman spectroscopy e differential scanning calorimetry techniques were used to study their structural properties. Reflectance and transmittance spectroscopy were used to obtain of the refraction index and of the extinction coefficients dispersion in the UVVis region for doped samples with different concentrations of CdS. The Brewster angle technique also was used to determine the refraction index of the different samples. The refraction index values obtained using the reflectance and transmittance measurement in the UV-Vis region and Brewster angle technique were compared and the results showed that the Brewster angle technique besides presents values that check with the literature, presented values with high precision. Measurements of optically induced birefringence were accomplished. Were obtained results of the photo induced birefringence by a photon for different concentrations of CdS for sample and for different intensities of the excitement light. The results were quantified using some of the principal theoretical models, where was observed that the pure epoxy resin presents photo induced birefringence and the addition of the CdS contributes to the increase of the birefringence.