Thesis submitted in fulfilment of the requirements for the degree Master of Technology: Civil Engineering in the Faculty of Engineering at the CAPE PENINSULA UNIVERSITY OF TECHNOLOGY 2014 / The current problems of orifice, nozzle and Venturi flow meters are that they are limited to turbulent flow and the permanent pressure drop produced in the pipeline. To improve these inadequacies, converging-diverging (C-D) tubes were manufactured, consisting of symmetrical converging and diverging cones, where the throat is the annular section between the two cones, with various angles and diameter ratios to improve the permanent pressure loss and flow measurement range. The objective of this study was firstly to evaluate the permanent pressure loss, secondly to determine the discharge coefficient values for various C-D tubes and compare them with the existing differential pressure flow meter using Newtonian and non-Newtonian fluids, and finally to assess the performance of these differential pressure flow meters. The tests were conducted on the multipurpose test rig in the slurry laboratory at the Cape Peninsula University of Technology. Newtonian and non-Newtonian fluids were used to conduct experiments in five different C-D tube flow meters with diameter ratios (β) of 0.5, 0.6 and 0.7, and with angles of the wall to the axis of the tube (θ) of 15°, 30° and 45°. The results for each test are presented firstly in the form of static pressure at different flow rates. It was observed that the permanent pressure loss decreases with the flow rate and the length of the C-D tube. Secondly, the results are presented in terms of discharge coefficient versus Reynolds number. It was found that the Cd values at 15° drop earlier than at 30° and 45°; when viscous forces become predominant, the Cd increases with increasing beta ratio. The Cd was found to be independent of the Reynolds number for Re>2000 and also a function of angle and beta ratio. Preamble Performance of a symmetrical converging-diverging tube differential pressure flow meter Finally, the error analyses of discharge coefficients were assessed to determine the performance criteria. The standard variation was found to increase when the Reynolds number decreases. The average discharge coefficient values and their uncertainties were determined to select the most promising C-D tube geometry. An average Cd of 0.96, with an uncertainty of ±0.5 % for a range of Reynolds numbers greater than 2,000 was found. The comparison between C-D tubes 0.6(15-15) and classical Venturi flow meters reveals that C-D 0.6(15-15) performs well in turbulent range and shows only a slight inaccuracy in laminar. This thesis provides a simple geometrical differential pressure flow meter with a constant Cd value over a Reynolds number range of 2000 to 150 000.

Submitted to the Department of Electrical Engineering in Fulfilment of the Requirements for the Magister Technologiae in Electrical Engineering at the Cape Peninsula University of Technology SUPERVISOR: E. VOSS NOVEMBER 2013 / The reluctance synchronous machine (RSM) operates on the principle of magnetic reluctance, which is produced through a careful selection of rotor flux barriers and cut-outs. Magnetic reluctivity is the resistance to magnetic flux and can be directly related to the principles of Ohm’s law in electrical circuits. Although reluctance motors have been known for more than 150 years, researchers lost interest when Nikola Tesla’s induction machine (IM) was introduced to industry. Over the last few decades, however, RSMs have shown a lot of potential. They are cheap, robust, reliable, and their rotors can also be used in the stators of IMs. The disadvantage of these machines is an inherently high torque ripple, being the result of its rotor geometry, but the biggest advantage is having a significant reduction in copper losses after the rotor cage has been removed. This advantage drove engineers to investigate, optimise and modify the performance and structure of this machine, which led to the usage of electronic drive systems. The recent advances in technology have allowed researchers to further investigate and modify the design and performance of this special type of machine, with the integration of Finite Element Analysis (FEA) software also making a contribution to the development of the RSM’s current driven systems. The voltage-fed RSM, driven direct-on-line (DOL) from the utility supply, was left in the shadows as the current-fed RSM took reign, but still is, in the author’s opinion, not yet fully analysed. This thesis practically investigates the performance characteristics of the cageless, voltage-fed 3kW RSM in its steady-state operation, under various loads. These performance characteristics are also compared to a RSM driven from a sensorless vector drive (current-fed) to investigate the advantages and disadvantages between the two. Experiments performed on the test bench immediately reveal a limitation to the voltage-fed RSM’s ability to drive higher loads. While the current-fed RSM conveniently reaches 150% of its full-load, the voltage-fed RSM, due to its cageless structure, only reaches 110% of its full-load power. Despite this discovery, the voltage-fed RSM proves to have a lower core loss, harmonic content and torque ripple. Using a FE software package with an integrated source-code, additional parameters such as the dq-axis inductances and currents are also compared and analysed in terms of its reaction to an increase in load. The eddy-current, hysteresis and excess losses are also analysed as well as the harmonic components caused by the geometry of the RSM. For academic purposes, a fair amount of emphasis is placed on the approach to the problem. The preparation for the FE simulation is explained in detail, providing insight into the FE mathematical model as well as parameter acquisition. These parameters include current angle, friction and windage losses, stator resistance, end-winding leakage reactance, core loss and inertia. The results obtained by the FE model are compared to that of the measured results and is found to have an error of only 0.52%. Furthermore, this study attempts to find the feasibility of the voltage-fed RSM’s practicality in modern-day industry. The conclusion is drawn that the voltage-fed RSM could be used as a more elegant alternative to an otherwise over-complicated and over-priced installation.

Submitted to the Department of Electrical Engineering in Fulfilment of the Requirements for the Magister Technologiae in Electrical Engineering at the CAPE PENINSULA UNIVERSITY OF TECHNOLOGY SUPERVISOR: E. VOSS NOVEMBER 2013 / Radial and peripheral displacement of stator teeth in electrical machines is known to be the cause of undesired vibration which leads to noise. This thesis serves to investigate the possibility of physically measuring the radial displacement of stator teeth caused by electromagnetic forces which, to the author’s knowledge, has not yet been achieved. A simplified practical approach is adopted in order to address the inherent difficulties attached to this problem, and the measurement of displacement is done by means of an experimental rig where a tooth is subjected to magnetic force acting over an air gap. Three experiments are carried out, each comprising ten tests, the results of which are compared in order to gain some idea as to the magnitudes of displacement which can be expected over a range of applied air gap flux densities. The aim of this work is to observe the displacement response of magnetised EM core material when acted upon by forces, and to see if the measured results agree with the elastic displacement predicted by a wellknown formula. It will be shown that although the measured results are in the same range as the predicted results, there is a deviation from the predicted linearity due to certain characteristics of the force rig, which are explained. The chosen measurement method is capacitive displacement and is shown to be a viable alternative to the more commonly used search coils and vibrometers in past literatures, especially when measuring displacements on the nano-scale. In addition, this study shows the importance of using 3D finite element software to simulate the electromagnetic model when saturation is present in the core of the test specimen. The important findings of this work are discussed in detail, and some ideas put forward, in an attempt to establish a starting point for future related work in the measurement of electromagnetic forceinduced displacement of stator teeth in electrical machines.

Thesis (MTech (Electrical Engineering))--Cape Peninsula University of Technology, 2009 / The purpose of this project is to develop methods for distribution network power quality' variations monitoring. Power quality (PO) has become a significant issue for both power suppliers and customers. There have been important changes in power system regarding to power quality requirements. "Power quality" is the combination at voltage quality and current quality. The main research problem of the project is to investigate the power quality of a distribution network by selection of proper measurement, applying and developing the existing classic and modern signal conditioning methods for power disturbance's parameters extracting and monitoring. The research objectives are: To study the standard lEC 61000-4-30 requirements. to investigate the common couplings in the distribution network. To identity the points for measurement, to develop MySQL database for the data from the measurement and to develop MATLAB software tor simulation of the network To develop methods based on Fourier transforms for estimation of the parameters of the disturbances. To develop software for the methods implementation, The influence of different loads on power quality disturbances are considered in the distribution network. Points on the network and meters according to the lEC power quality standards are investigated and applied for the CPUT Bellville campus distribution network. The implementation of the power quality monitoring for the CPUT Bellville campus helps the quality of power supply to be improved and the used power to be reduced. MATLAB programs to communicate with the database and calculate the disturbances and power quality parameters are developed.

Dissertation submitted in fulfilment of the requirements for the degree Magister Technologiae: Quality in the Faculty of Engineering at the Cape Peninsula University of Technology 2008 / Increasing customer demand for quality products and services have virtually forced organisations to adopt quality in every aspect of their business enterprises. Due to dynamic technological, political and economic changes in the world of business, the science of management is volatile. Higher Education Institutions are service providers and the customers thereof should be the focal point of their existence, requiring very specific structures to manage service quality within the various areas of application. After extensive research on customer complaint behaviours, the value of customer complaints have been highlighted, as it leads to useful insight into critical aspects pertaining to service organisations. Some customers 'pre-plan' complaints, and this act has been labeled as 'faked complaints'. This may lead to the organisation obtaining an image of service failure, however this is not a true representation of the organisation, thus impacting adversely on the efficiency of the organisation. The primary research objectives of this study are the following: ~ To identify key drivers underpinning complaints at the Cape Peninsula University ofTechnology (CPUT), in terms of service delivery. ~ To determine if management has a strategic focus on the quality of service to students at CPUT. ~ To demonstrate the impact that management has on the quality of service delivery. ~ To improve customer service at CPUT by minimizing complaints. It is anticipated that the research will lead to an improvement in the current state of service delivery at CPUT. By identifying and providing possible solutions to customer complaints and addressing problem areas, the research in addition should lead to improved communication between departments and communication between CPUT and its customers (students).

Master of Technology: Mechanical Engineering in the Faculty of Engineering at the Cape Peninsula University of Technology Supervisor:Prof Philander Oscar Bellville Campus Date of submission: April 2013 / The Advanced Manufacturing Technology Strategy (AMTS), predecessor of the Technology Innovation Agency, was a national strategy focused principally on improving collaboration amongst industry, academia and science councils. The aerospace industries and training institutions in particular have been identified as key thrust areas for achieving economic development through the AMTS. Furthermore, the AMTS Aerospace Interest Group has been identified as one of the most important facets of Micro and Nano Manufacturing, Sensors and Electronics Flagship Program. The manufacturing of Micro and Nano Electronics and sensors is essential for South Africa to sustain the technology capability development as seen in developed countries. For example, there is an urgent need to establish a Photo Lithography facility for South African industry and training Institutions. The demand for the new generations of industrial, military, commercial, medical, automotive and aerospace products in South Africa in particular, and in the world in general, has fuelled research and development activities focused on advanced and smart materials. This situation has allowed for the emergence of a new generation of infrared sensors, the bolometer, based on an infrared thermal detection mechanism which is particularly suited to operate at ambient temperature, opening opportunities for achieving low cost infrared imaging systems for both military and commercial applications. This work deals with different South African bolometer membranes of the second prototype in collaboration with the University of Pretoria and Denel Optronics. The bolometer is an infrared thermal sensor that measures thermal radiation by converting said radiation into a temperature change and subsequently measuring the induced change in electrical resistance. The term infrared from Latin Infra, meaning below, is usually applied to wavelengths between 700nm and 1mm. It can be argued that the first occurrence of infrared sensing actually goes back several millennia, when men placed their hands over recently extinguished fire. However, until Herschel’s experiment, this kind of infrared was between the sun and the earth. Thermal imaging, which refers to the ability to measure the temperature of different points on a scene, requires either an array of infrared detectors operating in those wavelength ranges or a way to scan a scene using a single detector. To realise this work, objectives have been assigned to different groups of the consortium represented by CPUT, UP and Denel. Analyses of thirteen bolometer membranes including metal bolometer (Titanium) and Vanadium oxide were assigned to CPUT, reason why this thesis focuses on the modelling, designing and testing of the bolometer membranes. Masks design of the second prototype bolometer test structures includes several thermally isolated bolometer devices. These devices have been modelled and analysed in order to study their electrical and thermal behaviour. / Cape Peninsula University of Technology University of Pretoria Denel Optronics

Thesis submitted in fulfilment of the requirements for the degree of Master of Technology: Biomedical Technology In the Faculty of Health and Wellness Sciences At the Cape Peninsula University of Technology Supervisors: Prof. Adriaan J Esterhuyse Dr Dirk J Bester Bellville January 2014 / Background: Oxidative stress and chronic inflammation contributes significantly to the pathogenesis of several ischaemic heart diseases, including atherosclerotic plaque rupture and myocardial infarction. It is widely demonstrated that ischaemia, followed by reperfusion, results in alterations of the mitochondrial and endothelial function through uncontrolled cascades of events characterized by free radical release and inflammation. Recent experimental evidence shows that modulation of inflammatory and antioxidant signaling mediators may determine the host outcome following myocardial ischaemia-reperfusion injury. Investigations from the past decade indicate that food supplements may play an important role in the prevention and management of chronic inflammatory diseases. Garcinia kola seeds are flavonoid rich nut from a tropical flowering, non-timber plant of the Guttiferae family. This plant is highly valued in several African cultures for its use in herbal medicine. Recently, the majority of experimental research has linked phytochemicals found in Garcinia kola nut, to its proposed beneficial effects in treatment and management of oxidative stress related-chronic diseases. Research performed in our laboratory demonstrated that kolaviron, a prominent Garcinia kola flavonoid extract, reduces myocardial apoptosis during ischaemia-reperfusion injury. Therefore, the aim of our current study was to determine the effects of Garcinia kola supplementation on cardiac inflammatory and antioxidant signaling pathways during ischaemia-reperfusion using a Wistar rat heart model. Materials and Methods: Male wistar rats were randomly divided into two groups: a control group receiving 2ml/kg corn oil and the experimental group receiving 100mg/kg Garcinia kola dissolved in corn oil, daily for 4 weeks. After the feeding period, blood samples were collected and lymphocytic DNA damage was analyzed using the alkaline comet assay. Furthermore, rat hearts were isolated and perfused with Krebs-Henseleit buffer on a working heart perfusion apparatus to measure myocardial functional parameters. Myocardial functional recovery was measured after 15 minutes global ischaemia followed by 25 minutes reperfusion. Hearts were freeze clamped at three different time points for myocardial cytokine concentration determinations using multiplex electrochemilunescent immunoassay. Nuclear factor kappa beta (NF- kβ), p38 mitogen activated protein kinases (p38 MAPK), protein kinase B/Akt (PKB/Akt), nitro-tyrosine, inducible nitric oxide (iNOS), cyclooxygenase-2 (COX-2), poly (adenosine-di-phosphate) ribose polymerase-1 (PARP-1) and caspase-3 expression and their phosphorylated forms (where applicable) were analyzed using the Western blot technique. Results: Dietary Garcinia kola supplementation significantly improved functional recovery when compared to the control group as reflected by the improved aortic output recovery (68.47 ± 6.16% versus 44.96 ± 7.00%; p<0.05). Our biochemical results supports the hypothesis that, dietary Garcinia kola supplementation modulates different cardiac proteins in terms of expression and activation at different time points when compared to the control group. We show that, before induction of ischaemia, Garcinia kola supplementation attenuates expression of inflammatory mediators and pro-apoptotic proteins when compared to the control group. The improved functional recovery was associated with a prompt inflammatory response, activation of PKB/Akt and attenuation of protein nitrosylation after 10 minutes of reperfusion. Modulation of NF-kβ and the p38 MAPK family proteins expression could have also played a significant role in myocardial functional recovery. Conclusion: We have shown that a 4 week period of dietary Garcinia kola supplementation at 100mg/kg daily improves cardiac functional recovery following ischaemia-reperfusion injury. We propose that dietary Garcinia kola supplementation protects cardiac myocytes from ischaemia-reperfusion induced oxidative stress through the induction of a prompt inflammatory response and controlled expression and/or activation of the, NF-kβ, PKB/Akt and p38 MAPK protein signaling pathways PARP-1 and caspase. Finally, we demonstrated that dietary Garcinia kola supplementation did not induce rat lymphocytic DNA damage when compared to the control group.

Thesis submitted in fulfilment of the requirements for the degree Master of Technology: Diagnostic Radiography, Department of Nursing and Radiography in the Faculty of Health Wellness Sciences at Cape Peninsula University of Technology 2014 / Aim: The aim of this study was to record the values of CTDIw and DLP displayed on the Computed Tomography (CT) scanner monitors of patients undergoing CT examinations of the head as Diagnostic Reference Levels (DRL) for dose optimisation in Northern Nigeria. Background: A brain CT scan is the most common CT examination performed, and this modality is recognized as delivering a high dose. CT, therefore, contributes significantly to the total collective effective dose to the population. Elimination of unnecessary or unproductive radiation exposure is necessary. To achieve this, practitioners must adhere to the principles of the justification of practices, and optimisation of radiation protection. Furthermore, the development of DRLs for the local context is advised. These reference doses are a guide to the expected exposure dose from a procedure and are useful as an investigation tool to identify incidences where patient doses are unusually high. Methodology: The study was conducted in three radiology departments with CT centres in Northern Nigeria. Data was collected, using a purposive sampling technique, from 60 consenting adult participants (weighing 70 ±3 kg) that had brain CT scans on seventh generations 4&16-slice GE and 16-slice Philips CT scanners. Prior to commencement of the study the CT scanners were certified by the medical physicists. For each brain scan, patient information, exposure factors, weighted computed tomography dose index (CTDIw), volume computed tomography dose index (CTDIvol) and dose length product (DLP) values were recorded. The data were analysed using SPSS version (16) statistical software. The mean, standard deviation and third quartile values of the CTDIw and DLP were calculated. An inter-comparison of the measured doses from the three research sites was conducted. A combined dose for the three centres was calculated, and compared with the reported data from the international communities where there are established DRLs. Results: The mean CTDIw and DLP values were: centre A (88 mGy and 713 mGy.cm), centre B (68 mGy and 1098 mGy.cm), and centre C (70 mGy and 59 mGy.cm). Comparison of CTDIw and DLP for the scanners of the same manufacturers showed statistically significant differences (p=0.003) and (p=0.03) respectively. In the case of the scanners of a different model but the same number of slices, the comparison of DLP was statistically significant (p=0.005) while no significant difference was noted in the measured CTDIw. Third quartile values of the cumulative doses of CTDIw and DLP, for Northern Nigeria were determined as 77 mGy and 985 mGy.cm respectively. Conclusion: The study has established Local DRLs (LDRLs) which are significantly higher than most of the reported data in the literature. Also dose variation between centres was noted. Optimization is thus recommended. Keywords: Head Imaging, Radiation Dose, Dose optimization, Computed Tomography, Local Diagnostic Reference Levels, Radiation Protection

Thesis submitted in fulfilment of the requirements for the degree Master of Technology: Radiography in the Faculty of Health and Wellness Sciences at the Cape Peninsula University of Technology Supervisor: Ms. Ferial Isaacs Co-supervisor: Prof. Susan J. Van Rensburg Bellville September 2013 / Multiple Sclerosis (MS) is characterised by demyelination within the central nervous system (CNS), which may result in neurological disabilities over time, causing considerable hardship to patients and their families, in addition to being costly to treat. Recent studies have linked MS to impaired cerebral blood flow, called chronic cerebrospinal venous insufficiency (CCSVI). Anecdotal evidence has suggested that surgical correction thereof results in improvement of symptoms experienced by MS patients. To my knowledge, no information is available in the literature on carotid artery disease in MS. The USA National MS Society has therefore called for more research to be done in this area. This cross-sectional observational sub-study will determine, by ultrasound (B-Mode, Colour and Pulsed-wave Doppler), the prevalence of chronic venous insufficiency (CCSVI) and carotid artery disease in the selected sample of MS patients within the region of the Western Cape, South Africa. Biochemical data; lifestyle factors such as physical activity and smoking; and nutritional status of MS patients were determined from the main study entitled: “The development of a comprehensive gene-based, pathology supported intervention program for improved quality of life in patients diagnosed with multiple sclerosis” (Division of Chemical Pathology, NHLS, Tygerberg Hospital, and University of Stellenbosch). Twenty-nine (29) patients were aged between 28-64years and they suffered from MS for 0.83-27years. A larger proximal and mid cross-sectional diameter (CSD) of the right IJV compared to the left (differences significant, P= 0.026 and P=0.023) was demonstrated. Increased intima media thickness (IMT) was present in 13.33% of the non-smoking MS group and 20% in the smoking MS group. IJV reflux was evident in 13.33% of the MS group. A significant reduction of cross-sectional diameters of the IJV’s was evident in smoking MS patients; suggesting that smoking is not only a risk factor for atherosclerotic disease but could also be related to narrowing of the major neck veins. This study also supports findings of other studies viz that there’s no significant correlation between extracranial venous abnormalities and MS. Early carotid artery disease was noted in smoking and non-smoking MS patients, however the findings were non-significant.

Magister Bibliothecologiae - MBibl / The aim of the research project is to investigate the effectiveness of an information literacy intervention for first year engineering students at the Cape Peninsula University of Technology. Information literacy has been identified as a necessary outcome of tertiary education. It refers to the life-long learning competencies of finding and using information in order to solve problems, to make decisions and to create new knowledge. Information literacy education has evolved from earlier forms of library user education, such as bibliographic instruction, and is central to the mission of academic libraries. However, librarians responsible for information literacy programmes seldom evaluate the effectiveness of their interventions. In today's climate of accountability and outcomes-based education, it is necessary to provide evidence of the benefits of the user education that libraries provide. The researcher uses the American College and Research Library (ACRL) Information Literacy Competency Standards for Higher Education, which are internationally recognized and widely used by South African academic librarians, as a benchmark to evaluate an intervention for a group of first year students enrolled for a mechanical engineering course. The intervention consists of two workshops which aim to teach the students to find information relevant to their essays via the university's OPAC, various engineering databases and to teach them how to reference and cite their sources in their essays. The research methodology assessed students' information literacy before and after the two workshops with the use of a questionnaire consisting of a set of questions based on some of the ACRL standards. The questionnaire also gathered data on students' prior experience of libraries, reading and computers, which might impact on their information literacy. / South Africa