No description available.

Graphene is a two-dimensional carbon structure that exhibits remarkable structure-property relations. Consequently, there has been immense effort undertaken towards developing methods for graphene synthesis. Chemical vapor deposition (CVD) and chemical exfoliation from colloidal suspensions are two common methods used for obtaining graphene films. However, the underlying experimental conditions have to be carefully optimized in order to obtain graphene films of controllable thickness and morphology. In this context, a significant part of this dissertation was devoted towards developing and improving current CVD-based and chemical exfoliation based methods for synthesizing high quality graphene films. Specifically, in the CVD based procedure for growing graphene on copper, the effect of surface pretreatment of copper was investigated and the quality of graphene grown using two different pretreatment procedures was compared and analyzed. In particular, graphene grown on electropolished copper (EP-Cu) was analyzed with respect to its surface morphology, surface roughness and thickness, and compared with graphene grown on as cold-rolled acetic acid cleaned copper (AA-Cu). It was shown that electropolishing of the Cu substrates prior to graphene growth greatly enhanced the ability to obtain flat, uniform, predominantly single layer graphene surface coverage on copper. The reported surface roughness of the graphene on EP-Cu was found to be much lower than for previously reported systems, suggesting that the electropolishing procedure adopted in this work has great promise as a pretreatment step for Cu substrates used in CVD growth of graphene. Obtaining graphene from colloidal suspensions of graphitic systems was also examined. In this work, an acid (H₂SO₄ + HNO₃) treatment process for intercalating natural graphite flakes was examined and the ability to reversibly intercalate and deintercalate acid ions within graphitic galleries was investigated. More importantly, a rapid-thermal expansion (RTP) processing was developed to thermally expand the acid-treated graphite, followed by exfoliation of predominantly bilayer graphene as well as few layer graphene flakes in an organic solvent (N, N-Dimethylformamide - DMF). The developed method was shown to provide bilayer and few layer graphene flakes in a reliable fashion. Fullerene is another carbon nanostructure that has garnered attention due to unique structure and chemical properties. Recently, there has been increased focus towards harnessing the properties of fullerenes by synthesizing fullerene self-assemblies in the form of extended rods, tubes and more complex shapes. Current methods to synthesize these self-assemblies are either cumbersome, time consuming or expensive. In this context, an alternate, straightforward dip-coating procedure technique to self-assemble equal-sized, faceted, polymerized fullerene nanorods on graphene-based substrates in a rapid fashion was developed. By suitably modifying the kinetics of self-assembly, the ability to reliably control the spatial distribution, size, shape, morphology and chemistry of fullerene nanorods was achieved.

The thesis consists of four parts of which part 1 presents a brief overview of nanomaterials. Parts 2, 3 and 4 contain results of investigations of graphene, nanofilms of noble metal nanoparticles and ZnO nanostructures respectively. Investigations of graphene are described in Part 2 which consists of six chapters. In Chapter 2.1, changes in the electronic structure and properties of graphene induced by molecular charge-transfer have been discussed. Chapter 2.2 deals with the results of a study of the interaction of metal and metal oxide nanoparticles with graphene. Electrical and dielectric properties of graphene-polymer composites are presented in Chapter 2.3. Chapter 2.4 presents photo-thermal effects observed in laser-induced chemical transformations in graphene and other nanocarbons system. Chapter 2.5 describes the mechanical properties of polymer matrix composites reinforced by fewlayer graphene investigated by nano-indentation. The extraordinary synergy found in the mechanical properties of polymer matrix composites reinforced with two nanocarbons of different dimensionalities constitute the subject matter of Chapter 2.6. Investigations of noble metal nanoparticles have been described in Part 3. In Chapter 3.1, ferromagnetism exhibited by nanoparticles of noble metals is discussed in detail while Chapter 3.2 deals with surface-enhanced Raman scattering (SERS) of molecules adsorbed on nanocrystalline Au and Ag films formed at the organic–aqueous interface. Factors affecting laser-excited photoluminescence from ZnO nanostructures are examined in great detail in Part 4.

La plupart des équipements électroniques et électriques sont enrobés ou encapsulés par de la résine epoxy, choisie pour ses qualités physiques, chimiques et surtout diélectriques. Cependant, ce matériau présente un inconvénient majeur : sa faible conductivité thermique (0.2 W/mK). Dans ce contexte, nous avons élaboré et caractérisé des composites epoxy / carbone dans le but d’améliorer la conductivité thermique de ce type de résine tout en conservant ses propriétés diélectriques. Nous avons ainsi testé le potentiel d’une large gamme de charges carbonées, de structures, formes et tailles variées (sphères, tubes et plaquettes), telles que des micro-sphères de carbone et des nanotubes multi-parois synthétisées par CVD et PECVD, mais aussi des charges industrielles : nano-plaquettes de graphite (graphite exfolié), du coke de pétrole, du graphite synthétique et naturel. Des échantillons de matériaux composites massifs (50 x 50 x 4 mm) ont été préparés à partir d’une résine industrielle DGEBA de viscosité élevée 8.5-15 Pa.s, en faisant varier le taux de charge. Les propriétés thermiques des composites ont été mesurées à partir de la technique du hot disk (source plane instationnaire). Les meilleurs résultats ont été obtenus à partir des nano-plaquettes de graphite : les conductivités thermiques des composites ont atteint (0.55 W/mK) pour une charge admissible maximale de 2.67 vol.%. L’accroissement relatif de conductivité thermique a été de 66 % pour 1 vol.%. Cet accroissement est particulièrement élevé dans la mesure où les meilleurs résultats reportés sont de 20 % / vol.% dans le cas de résines à viscosité plus faible de type DGEBF (2.5 - 4.5 Pa.s). La concentration de charge admissible (1.3 vol.%) pour conserver une résistivité électrique suffisamment élevée (> 105 ohm.m) nous a permis d’atteindre une conductivité thermique de 0.37 W/mK (soit une augmentation de 100% par rapport à la résine initiale). Ces résultats sont interprétés en termes de transport des phonons acoustiques dans un système composite bi-phasique. Les nano-plaquettes de graphite sont caractérisées par une morpholigie anisotrope, d’ une surface d’environ 26 x 26 microns dont l’épaisseur est de l’ordre de 6 nm. Elles combinent une structure lamellaire périodique bien ordonnée dans les plans de graphène (caractérisation par XPS, EDX et DRX), et des rapports d’acicularité élevés ( 4300), estimés à partir de différentes techniques : TEM, SEM et BET. Nous montrons qu’accroitre l’acicularité des nano-plaquettes de graphite par exfoliation, en préservant une grande surface des plans de graphène, et sans générer de défauts de structure, constitue un défi. Cette morphologie 2D particulière permet d’une part de conserver voire augmenter la conductivité intrinsèque des charges, favorisée dans les plans de graphène, et d’autre part, en raison de leur grande surface spécifique, de garantir après leur dispersion dans la résine, un meilleur transport des phonons acoustiques dans le composite. / Most electronic and electrical equipment are coated or encapsulated by epoxy resin due to its physical, chemical and dielectric properties. However, this material has a major drawback: its low thermal conductivity ( 0.2 W / mK). In this context, we have developed and characterized epoxy / carbon composites in order to improve the thermal conductivity of this type of resin while maintaining its dielectric properties. We have tested the potential of a wide range of carbonaceous fillers, structures, shapes and sizes (spheres, tubes and plates), such as carbon micro-spheres and multi-walled carbon nanotubes synthesized by CVD and PECVD, but also industrial fillers: graphite nano-platelets (exfoliated graphite), petroleum coke, synthetic and natural graphite. Large composite samples (50 x 50 x 4 mm) were prepared from a DGEBA engineering resin of high viscosity 8.5-15 Pa.s, by varying the charge vol%. The thermal properties of the composites were measured from the transient plane source technique (hot disk). The best results are obtained from graphite nano-platelets: the thermal conductivity reach (0.55 W / mK) for a maximum load of 2.67 vol%.. The relative increase of thermal conductivity is 66% to 1 vol.%. This increase is particularly high to the extent that the best results reported so far is 20% / vol% for resins with lower viscosity, type DGEBF (2.5 - 4.5 Pa.s). The allowable concentration (1.3 vol.%) to maintain a sufficiently high electrical resistivity (> 105 ohm.m) permits to increase of the thermal conductivity to 100% (0.37 W / mK) compared to the initial resin. These results are interpreted in terms of transport of acoustic phonons in the composite two-phase system. Graphite nano-platelets are characterized by anisotropic shapes with a surface of about 26 x 26 microns whose thickness is of the order of 6 nm. They combine an ordered periodic structure in graphene planes (characterization by XPS, EDX and XRD), and a high aspect ratio ( 4300), estimated using various techniques: TEM, SEM and BET. We show that graphite exfoliation permit to increase the aspect ratio of graphite nanoplatelets, maintaining large micronic graphene surface, and without generating structural defects is a challenge. This peculiar 2D morphology allows on one hand, to retain or even increase the intrinsic filler conductivity, favored in the graphene planes, and on another hand, due to their high surface area, to ensure after their dispersion in the resin, a better transport of acoustic phonons through the composite.

Submitted by MARCIA ROVADOSCHI (marciar@unifra.br) on 2018-08-20T12:17:09Z No. of bitstreams: 2 license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) Tese_IuriMedeirosJauris.pdf: 8625676 bytes, checksum: 6980ea50a786db7523d0559ac05b09bb (MD5) / Made available in DSpace on 2018-08-20T12:17:09Z (GMT). No. of bitstreams: 2 license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) Tese_IuriMedeirosJauris.pdf: 8625676 bytes, checksum: 6980ea50a786db7523d0559ac05b09bb (MD5) Previous issue date: 2016-11-21 / Various chemical pollutants and substances named endocrine disruptors compounds (EDCs) has become commonly detected in wastewater and even in drinking water in many countries. In contrast the adsorption technique has been considered by many researcher as a promising method to treatment and purification of wastewater, mainly due to its ease of operation, high efficiency and low cost. Meanwhile, carbon nanomaterials such as nanotubes, and graphene, have been reported in the literature as promising materials to adsorb and removing various types of contaminants from wastewater. From this perspective, the main goal of this study was the evaluation of the use of graphene, functionalized graphene and reduced graphene oxide (rGO), in the adsorption and removal of drugs in aqueous medium. The removal efficiency was measured using diclofenac sodium (DCL) and nimesulide (NIME) in aqueous solutions and analizing sorption equilibrium conditions as well as kinetics and adsorption isotherms in the rGO. At the same time, through ab initio calculations, computational simulations were carried out to better understand how the structural and electronic characteristics of the adsorbent material can influence the adsorption process. Thus, through the batch experiments, it was found that the rGO showed a good ability to successfully remove NIME and DCL drugs from aqueous solutions. The maximum percentage removal of DCL by rGO was 80.4% and 79.3% for the initial concentrations of 40 and 70 mg.L-1, respectively. The maximum sorption capacity for adsorption of the DCL drug at 25ºC was 59.67 mg.g-1. The maximum percentage removal of NIME by rGO was 92.2% and 82.9% for the initial concentrations of 40 and 70 mg.L-1, respectively. The thermogravimetric and FTIR spectroscopy analyzes revealed that DCL and NIME was successfully adsorbed by rGO. In addition, theoretical results showed that the interaction between DCL and NIME with pristine or functionalized graphene, occurs by physical adsorption, being maintained mainly due to π-π interactions and hydrogen bonding. The results provide valuable information for better understanding the behavior of physicochemical properties in the evaluated interactions. Based on these results, the ab initio calculations and the adsorption experiments point out that the graphene and functionalized graphene or rGO are promising materials for extracting DCL and NIME drugs from wastewater effluents. / A detecção de poluentes químicos diversos e substâncias conhecidas com interferentes endócrinos (IEs) em águas residuais e até mesmo na água potável, tem se tornado cada vez mais frequente em inúmeros países. Em contrapartida a técnica de adsorção, tem sido considerado por muitos pesquisadores como um método promissor de tratamento e purificação da água proveniente de efluentes, devido, principalmente, a sua facilidade de operação, alta eficiência e baixo custo. Paralelamente, os nanomateriais de carbono, tais como nanotubos e o grafeno vêm sendo reportados na literatura como materiais de grande capacidade para adsorção e remoção de diversos tipos de produtos químicos de águas residuais. Nesse sentido, o foco desse estudo foi a avaliação do uso do grafeno, grafeno funcionalizado e óxido de grafeno reduzido (rGO), na adsorção e remoção de fármacos em meio aquoso. A avaliaçao da eficiência de remoção foi conduzida empregando-se diclofenaco sódico (DCL) e a nimesulida (NIME) em soluções aquosas e avaliando-se as condições de equilíbrio de sorção e também cinética e isotermas de adsorção no rGO. Paralelamente, através de cálculos de primeiros princípios, foram realizadas simulações computacionais para melhor compreensão de como as características estruturais e eletrônicas do material adsorvente, podem influenciar no processo adsortivo. Assim, através dos experimentos em batelada, observou-se um percentual de remoção máximo do DCL pelo rGO de 80,4% e 79,3% para as concentrações iniciais de 40 e 70 mg.L-1. A capacidade máxima encontrada de adsorção do DCL pelo rGO a 25ºC foi de 59,67mg.g-1. O percentual de remoção máximo da NIME pelo rGO foi 92,2 % e 82,9% para as concentrações iniciais de 40 e 70 mg.L-1 . O pH foi fixo em 10,0 para todos os experimentos. As análises termogravimétricas para adsorção do DCL e NIME em rGO, e de espectroscopia FTIR para adsorção da NIME em rGO, revelaram que os fármacos foram adsorvidos com sucesso pelo rGO. Em adição os resultados teóricos mostraram que a interação do DCL e da NIME com o grafeno puro e os grafenos funcionalizados ocorreram através da adsorção física, sendo essa mantida em grande parte devido às interações do tipo π-π e ligações de hidrogênio. Os resultados obtidos fornecem subsídios para a melhor compreensão do comportamento das propriedades físico-químicas nas interações avaliadas. Baseado nesses resultados, os cálculos de primeiros princípios e os experimentos de adsorção revelaram que o grafeno puro, grafeno funcionalizado, ou rGO, são materiais promissores para remoção dos fármacos DCL e NIME de soluções aquosas.

Different carbon nanostructures have different properties and different applications. It is needed to synthesize good quality and also on large scale. From the point of industrial applications, highly productive and low cost synthesis method is very essential. Research has been done extensively on the intrinsic and individual properties of both single walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWC-NTs) in the range of nanometer to micrometer length scale. The important question is how the properties change beyond this length scale and if they are used in group in the form of an array instead of the individual carbon nanotubes (CNTs). Some applications require large current output, large energy production etc. For such kind of applications, it becomes essential to use CNTs in large number in the form of arrays or array, instead of using large numbers of CNTs in individual level. Future nanotechnology scope requires large scale application using the very rich intrinsic properties of the CNTs and nanomaterials. Keeping these problems and challenges in front, this thesis work is devoted to the research of the large scale synthesis of mm long MWCNTs, having different morphology and studies on various physical properties of MWCNTs in the form of arrays. Synthesis of mm long aligned and buckled MWCNTs have been reported for the first time. Generally buckled CNTs were obtained by compressing the straight CNTs. Apart from this, different morphologies like, aligned straight, helical or coiled CNTs are also synthesized. Resistance of the individual CNT increases with the increase in length. Resistance versus length of an array of CNT also shows similar behaviour. The thermal conductivity of CNT array is observed to decrease with the increase of array diameter (diameter �100 µm). There are few reports of the similar behaviour with the experiments done on small diameter CNT arrays (diameter �100 nm). From these observations, it seems that in the arrays of CNT, their intrinsic individual property is preserved though the magnitudes are different. The conductance measurements done on buckled CNT array by compressing it to apply uniaxial strain, shows the conductance oscillation. This conductance oscillation seems to be originating from the band gap change due to strain when the CNTs bend during compression. Recent research focuses on the arrays of CNT as they can carry large current of the order of several milliamperes that make the arrays suitable in nanoscale electronics and in controlling macroscopic devices such as light emitting diodes and electromotors. Regarding this aspect, a part of this thesis work is devoted on the application of CNT array to field effect transistor (FET) and study of thermoelectric power generation using CNT arrays. The entire thesis is based on the works discussed above. It has been organized as follows: Chapter 1 deals with introduction about the different carbon nanostructures and different synthesis methods. A brief introduction about the different current-voltage (IV) characteristics of SWCNTs and MWCNTs, length and diameter dependence and effect of the mode of contacts, are given. Some applications of the array of CNTs like buckling effect on compression, stretching of CNT into the form of rope, and conduction change on compression are discussed. Application of CNT as FET, as a thermometer, and thermoelectric effect of CNT are discussed. The electromechanical effect of CNT is also discussed briefly. Chapter 2 deals with experimental setup for synthesis of different morphologies of carbon nanostructures. The samples are characterized using common characterization techniques like, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. A brief introduction about Raman Spectroscopy of CNT is given. Chapter 3 reports the unusual IV characteristics and breakdown of long CNT arrays. The current carrying ability and the threshold voltage as a function of array diameter are reported. The effect of the ambient like temperature and pressure are discussed. Chapter 4 deals with theoretical models to analyze the IV characteristics reported in Chapter 3. It has been shown that a set of classical equations are applicable to quantum structures and the band gap can be evaluated. Chapter 5 describes with application of CNT arrays as temperature sensors. It has been shown that CNT arrays of suitable diameters are used as temperature sensors after calibration. Chapter 6 reports the high current FET application of CNT arrays. Effects of temperature and ambient pressure are discussed. The type of the majority charge carrier is determined. Chapter 7 deals with application of CNT arrays as thermoelectric power generator to get large thermoelectric current. Effects of different array diameter are discussed. Modulation of thermoemf with gate voltage is discussed. The type of the majority charge carrier is determined. Chapter 8 reports the effect of compressive strain on buckled MWCNT arrays. Conductance is measured during the compression of the array. Quantum electromechanical conductance oscillation is observed. The structural changes are observed with SEM. Raman spectroscopic study supports the explanation of the effect. Chapter 9 provides the conclusion and overall summary of the thesis.

Orientadores: Munir Salomão Skaf, Vitor Rafael Coluci / Tese (doutorado) - Universidade Estadual de Campinas, Instituto de Química / Made available in DSpace on 2018-08-26T20:42:42Z (GMT). No. of bitstreams: 1 Faro_TatianaMellodaCosta_D.pdf: 8054394 bytes, checksum: ce0d79df42ce453ffc39b51bf0ad1094 (MD5) Previous issue date: 2015 / Resumo: Atualmente, a economia mundial depende do uso de combustíveis fósseis para a geração de energia. Esse modelo apresenta problemas ambientais graves, uma vez que o petróleo é um material não-renovável e muito poluente. O gás hidrogênio apresenta-se como uma alternativa promissora para substituir os combustíveis utilizados atualmente devido a um conjunto de características positivas: ele é atóxico, tem uma alta densidade energética gravimétrica e gera apenas água como produto de sua combustão. Apesar de tais vantagens, ele ainda não é utilizado comercialmente em larga escala. O maior empecilho tecnológico para que o hidrogênio possa substituir os combustíveis fósseis está no seu armazenamento. Existem diversas propostas para armazenar o hidrogênio, como tanques contendo o hidrogênio nas formas de gás pressurizado ou de líquido, além de sistemas sólidos que permitam a sua adsorção. Todavia, nenhum sistema construído até então foi capaz de armazenar o hidrogênio de forma tão barata, segura e eficaz quanto seria necessário. Nanoestruturas de carbono são vistas como uma boa alternativa para construir dispositivos de armazenamento de hidrogênio baseados na fisissorção. Os nanopapiros de carbono, formados por folhas de grafeno enroladas no formato de um papiro, são considerados particularmente promissores para armazenar o hidrogênio, uma vez que possuem uma alta área superficial, extremidades abertas e distâncias intercamadas facilmente controláveis. Na primeira etapa deste trabalho, realizamos simulações de Dinâmica Molecular (MD) para estudar a dinâmica e a estabilidade de diversos nanopapiros em função de alguns dos seus parâmetros estruturais. Posteriormente, aplicamos o método de Monte Carlo Grand-Canônico (GCMC) para estudar o processo de adsorção de hidrogênio em nanopapiros selecionados, de forma a caracterizar quantitativamente e qualitativamente as fases adsorvidas / Abstract: Presently, the world economy depends on the use of fossil fuels to generate energy. This model presents serious environmental problems, since petroleum is a non-renewable and very pollutant material. Hydrogen gas presents itself as a promising alternative to substitute the fuels currently used due to a few positive characteristics: it is non-toxic, possesses a high gravimetric energetic density and only generates water as a combustion byproduct. In spite of all these advantages, hydrogen still isn't used commercially in a large scale. The biggest technological drawback for hydrogen to substitute fossil fuels is in its storage. There are many proposed ways to store hydrogen, such as tanks containing highly pressurized or liquid hydrogen, or solid systems that allow its adsorption. However, no system built up to the date had been able to store hydrogen as cheap, safe and efficiently as necessary. Carbon nanostructures are seen as a good alternative to build hydrogen storage devices based on physisorption. Carbon nanoscrolls, formed by graphene sheets scrolled in a papirus-like shape, are considered as particularly promising adsorption materials, since they possess a high surface area, open edges and easily controllable interlayer distances. In the first step of this work, we made Molecular Dynamics (MD) simulations to study the dynamics and the stability of several nanoscrolls as a function of their structural parameters. Subsequently, we used the Grand-Canonical Monte Carlo (GCMC) method to study the hydrogen adsorption process in selected nanoscrolls, as to characterize the adsorbed phases quantitatively and qualitatively / Doutorado / Físico-Química / Doutora em Ciências

Die vorliegende Promotion beinhaltet die Untersuchung von irregulären Kohlenstoff-Nanostrukturen, die mittels Hochenergie-Kugelmahlen hergestellt wurden. Die wissenschaftliche Herausforderung besteht darin, die strukturelle Vielfalt dieser Nanostrukturen experimentell zu erfassen, zu klassifizieren und bezüglich ausgewählter Eigenschaften zu bewerten, sowie mit den Herstellungsparametern in Zusammenhang zu bringen. Die Pulver konnten nach den Mahlungen hinsichtlich ihrer Struktur in zwei grundsätzliche Typen eingeteilt werden: (I) ein Nanopulver, das aus graphitischen Stapelpaketen besteht, welche in eine amorphe Matrix eingebettet sind, (II) ein vollständig amorphisiertes Pulver. Die Strukturanalyse in Bezug auf die Mahlbedingungen (Mahlatmosphäre, Mahltemperatur) zeigt, dass die Dauer der Nanostrukturierung sowie die Anzahl und Größe von graphitischen Stapelpaketen gezielt beeinflusst werden kann. Außerdem konnten Hinweise gefunden werden, die darauf hindeuten, dass Mahlen bei tiefen Temperaturen oder unter Wasserstoffatmosphäre die Agglomeration der Nanopartikel verringern kann. Das Kugelmahlen ermöglicht es ebenfalls, die spezifische Oberfläche des Graphitpulvers von 5,5 m2/g auf 725 m2/g innerhalb von fünf Mahlstunden zu erhöhen. Der Anteil der Verunreinigungen (Fe) liegt dabei nicht höher als 0,05 wt%. Es ist jedoch zu beachten, dass sämtliche Eigenschaften stark von den verschiedenen Mahlparametern (Mahltemperatur, Mahlmaterial) abhängen. Die für Adsorptionsuntersuchungen optimalen Eigenschaften (große spezifische Oberfläche, erhöhte Reaktivität, geringe Verunreinigungen) werden schon nach kurzer Mahldauer erreicht. Wiederholungsmahlungen und Wiederholungsmessungen verschiedener Eigenschaften (spezifische Oberfläche, Verbrennungstemperatur) machen deutlich, dass die Ergebnisse reproduzierbar sind, und dass keine Alterungserscheinungen während der Lagerung unter Argonatmosphäre im Zeitraum von einem Jahr auftreten. Die Wasserstoffspeicherung an nanostrukturierten Kohlenstoffpulvern konnte nachgewiesen werden. Die maximalen Speicherkapazitäten für Temperaturen nahe 77 K lagen bei 1,5 wt%. Für niedrigere Temperaturen Tist = 35 K zeigten sich höhere Speicherkapazitäten von bis zu 5 wt%. Die Korrelation der ermittelten Speicherkapazitäten mit den theoretisch erreichbaren Werten in Bezug auf die Oberfläche der Proben zeigt, dass im Experiment deutlich höhere Werte erhalten werden. Dies lässt den Schluss zu, dass neben der Speicherung an der Oberfläche der Pulver ein weiterer Speichermechanismus innerhalb der Mikroporen der Proben stattfindet.

L’environnement réactif du plasma constitue un outil puissant dans la science des matériaux, permettant la création de matériaux innovatifs et l'amélioration de matériaux existants qui ne serait autrement pas possible.Le plasma fournit simultanément des fluxes de particules chargées, des molécules chimiquement actives, des radicaux, de la chaleur, des photons, qui peuvent fortement influencer les voies d'assemblage à différentes échelles temporelles et spatiales, y compris à l’échelle atomique.Dans cette thèse de doctorat, des méthodes tenant pour base des plasmas micro-ondes ont été utilisées pour la synthèse de nanomatériaux de carbone, y compris graphène, graphène dopé à l'azote (N-graphène) et structures de type diamant.À cette fin, ce travail est lié à optimisation de la synthèse de nanostructures 2D du carbone, comme graphène et N-graphène par la poursuite de l'élaboration et du raffinement de la méthode développée en Plasma Engineering Laboratory (PEL). La synthèse de graphène de haute qualité et en grandes quantités a été accomplie avec succès en utilisant des plasmas d'Ar-éthanol à ondes de surface dans des conditions de pression ambiante. De plus, le N-graphène a été synthétisé par un procédé en une seule étape, de l'azote a été ajouté au mélange d’Ar-éthanol, et par un procédé en deux étapes, en soumettant des feuilles de graphène préalablement synthétisées ont été exposées à un traitement plasma argon-azote à basse pression. Les atomes d'azote ont été incorporés avec succès dans le réseau de graphène hexagonal, formant principalement liaisons pyrroliques, pyridiniques et quaternaires. Un niveau de dopage de 25 at.% a été atteint.Différents types de nanostructures de carbone, y compris du graphène et des structures de type diamant, ont été synthétisées au moyen d'un plasma d’argon en utilisant du méthane et du dioxyde de carbone comme précurseurs du carbone.De plus, des plasmas à couplage capacitif ont également été utilisés pour la fonctionnalisation du graphène et pour la synthèse de nanocomposites, tels que les composites de Polyaniline (PANI)-graphène. Les utilisations potentielles de ces matériaux ont été étudiées et les deux structures ont démontré avoir des attributs remarquables pour leur application aux biocapteurs. / Plasma environments constitute powerful tools in materials science by allowing the creation of innovative materials and the enhancement of long existing materials that would not otherwise be achievable. The remarkable plasma potential derives from its ability to simultaneously provide dense fluxes of charged particles, chemically active molecules, radicals, heat and photons which may strongly influence the assembly pathways across different temporal and space scales, including the atomic one.In this thesis, microwave plasma-based methods have been applied to the synthesis of advanced carbon nanomaterials including graphene, nitrogen-doped graphene (N-graphene) and diamond-like structures. To this end, the focus was placed on the optimization of the production processes of two-dimensional (2D) carbon nanostructures, such as graphene and N-graphene, by further elaboration and refinement of the microwave plasma-based method developed at the Plasma Engineering Laboratory (PEL). The scaling up of the synthesis process for high-quality graphene using surface-wave plasmas operating at atmospheric pressure and argon-ethanol mixtures was successfully achieved. Moreover, N-graphene was synthetized via a single-step process, by adding nitrogen to the argon-ethanol mixture, and via two-step process, by submitting previously synthetized graphene to the remote region of a low-pressure argon-nitrogen plasma. Nitrogen atoms were usefully incorporated into the hexagonal graphene lattice, mainly as pyrrolic, pyridinic and quaternary bonds. A doping level of 25% was attained.Different types of carbon nanostructures, including graphene and diamond-like nanostructures, were also produced by using methane and carbon dioxide as carbon precursors in an argon plasma.Additionally, capacitively-coupled radio-frequency plasmas have been employed in the functionalization of graphene and in the synthesis of Polyaniline (PANI)-graphene composites. The potential uses of these materials were studied, with both showing favourable characteristics for their applicability in biosensing applications.

[pt] A pesquisa aponta para a possibilidade de realizar a reação de redução de CO2 (CO2RR) para a formação de nanomateriais de carbono por ablação a laser pulsado(PLA) de alvos magnéticos de Ferro(Fe) e Níquel(Ni) em água pura deionizada. Os materiais coloidais sintetizados foram caracterizados por diferentes técnicas de espectroscopias ópticas (UVVis, ICP-MS, FTIR e Raman) e microscopia eletrônica de transmissão (TEM), revelando a presença de nanopartículas de óxidos e hidróxidos de metais de transição, junto com nanomaterial orgânico. Esse último, é bem visível por TEM, espectroscopia de raio-X por dispersão em energia (EDS), espectroscopia por perda de energia de elétrons (EELS), e espectroscopia Raman, que indica a presença de carbono amorfo grafítico e vibrações CH. No caso do nanomaterial obtido do Níquel, os resultados FTIR confirmam a presença da fase do hidróxido beta-Ni(OH)2, enquanto as medidas Raman e TEM sugerem também a presença de nano-folhas de Ni(HCO3)2. Os resultados experimentais foram enfim discutidos no contexto da origem e da evolução de moléculas simples e complexas de interesse astroquímico, com foco especial nas espécies potencialmente formadas na superfície de pequenos corpos metálicos do Sistema Solar e grãos de poeira cósmica do meio interestelar. / [en] The proposed research points to the possibility to perform CO2 reduction reaction (CO2RR) to solid carbon nanomaterials by the pulsed laser ablation (PLA) of magnetic target of iron (Fe) and nickel (Ni) in pure deionized water. The synthesized colloidal dispersions were characterized by different optical spectroscopies (UV-Vis, ICP-MS, FTIR and Raman) and transmission electron microscopy (TEM), revealing the presence of nanosized transition metal oxide and hydroxide nanoparticles, together with organic nanomaterial. The latter is well visible by TEM, energy-dispersive X-Ray spectroscopy (EDS), electron energy-loss spectroscopy(EELS), and Raman spectroscopy, which indicates the presence of amorphous graphitic carbon and CH vibrations. In the case of Ni derived nanomaterial, FTIR results confirm the presence of a beta-Ni(OH)2 hydroxide phase, while Raman and TEM measurements suggest also the presence of Ni(HCO3)2 nanosheets. The experimental results were finally discussed in the frame of the origin and evolution of simple and complex molecules of astrochemical interest, with special focus on those species potentially formed on the surface of metallic minor bodies in the solar system and cosmic dust grains in the interstellar medium(ISM).