Spelling suggestions: "subject:"goal articles"" "subject:"goal 2articles""
1 |
The caking and swelling of South African large coal particles / Sansha CoetzeeCoetzee, Sansha January 2015 (has links)
The swelling and caking propensity of coals may cause operational problems such as
channelling and excessive pressure build-up in combustion, gasification and specifically in fluidised-bed and fixed-bed operations. As a result, the swelling and caking characteristics of certain coals make them less suitable for use as feedstock in applications where swelling and/or caking is undesired. Therefore, various studies have focused on the manipulation of the swelling and/or caking propensity of coals, and have proven the viability of using additives to reduce the swelling and caking of powdered coal (<500 μm). However, there is still a lack of research specifically focused on large coal particle devolatilisation behaviour, particularly swelling and caking, and the reduction thereof using additives. A comprehensive study was therefore proposed to investigate the swelling and caking behaviour of large coal particles (5, 10, and 20 mm) of typical South African coals, and the influence of the selected additive (potassium carbonate) thereon. Three different South African coals were selected based on their Free Swelling Index (FSI): coal TSH is a high swelling coal (FSI 9) from the Limpopo province, GG is a medium swelling coal (FSI 5.5-6.5) from the Waterberg region, and TWD is a non-swelling coal (FSI 0) from the Highveld region. Image analysis was used to semi-quantitatively describe the transient swelling and shrinkage behaviour of large coal particles (-20+16 mm) during lowtemperature devolatilisation (700 °C, N2 atmosphere, 7 K/min). X-ray computed tomography and mercury submersion were used to quantify the degree of swelling of large particles, and were compared to conventional swelling characteristics of powdered coals. The average swelling ratios obtained for TWD, GG, and TSH were respectively 1.9, 2.1 and 2.5 from image analysis and 1.8, 2.2 and 2.5 from mercury submersion. The results showed that coal swelling measurements such as FSI, and other conventional techniques used to describe the plastic behaviour of powdered coal, can in general not be used for the prediction of large coal particle swelling. The large coal particles were impregnated for 24 hours, using an excess 5.0 M K2CO3 impregnation solution. The influence of K2CO3-addition on the swelling behaviour of different coal particle sizes was compared, and results showed that the addition of K2CO3 resulted in a reduction in swelling for powdered coal (-212 μm), as well as large coal particles (5, 10, and 20 mm). For powdered coal, the addition of 10 wt.% K2CO3 decreased the free swelling index of GG and TSH coals from 6.5 to 0 and from 9.0 to 4.5, respectively. The volumetric swelling ratios (SRV) of the 20 mm particles were reduced from 3.0 to 1.8 for the GG coal, and from 5.7 to 1.4 for TSH. In contrast to the non-swelling (FSI 0) behaviour of the TWD powders, the large particles exhibited average SRV values of 1.7, and was found not be influenced by K2CO3-impregnation. It was found that the maximum swelling coefficient, kA, was reduced from 0.025 to 0.015 oC-1 for GG, and from 0.045 to 0.027 oC-1 for TSH, as a results of impregnation. From the results it was concluded that K2CO3-impregnation reduces
the extent of swelling of coals such as GG (medium-swelling) and TSH (high-swelling),
which exhibit significant plastic deformation. Results obtained from the caking experiments indicated that K2CO3-impregnation influenced the physical behaviour of the GG coal particles (5, 10, and 20 mm) the most. The extent of caking of GG was largely reduced due to impregnation, while the wall thickness and porosity also decreased. The coke from the impregnated GG samples had a less fluid-like
appearance compared to coke from the raw coal. Bridging neck size measurements were performed, which quantitatively showed a 25-50% decrease in the caking propensity of GG particles. Coal TWD did not exhibit any caking behaviour. The K2CO3-impregnation did not influence the surface texture or porosity of the TWD char, but increased the overall brittleness of the devolatilised samples. Both the extent of caking and porosity of TSH coke were not influenced by impregnation. However, impregnation resulted in significantly less and smaller opened pores on the surface of the devolatilised samples, and also reduced the average wall thickness of the TSH coke.
The overall conclusion made from this investigation is that K2CO3 (using solution
impregnation) can be used to significantly reduce the caking and swelling tendency of large coal particles which exhibits a moderate degree of fluidity, such as GG (Waterberg region). The results obtained during this investigation show the viability of using additive addition to reduce the caking and swelling tendency of large coal particles. Together with further development, this may be a suitable method for modifying the swelling and caking behaviour of specific coals for use in fixed-bed and fluidised-bed gasification operations. / PhD (Chemical Engineering), North-West University, Potchefstroom Campus, 2015
|
2 |
The caking and swelling of South African large coal particles / Sansha CoetzeeCoetzee, Sansha January 2015 (has links)
The swelling and caking propensity of coals may cause operational problems such as
channelling and excessive pressure build-up in combustion, gasification and specifically in fluidised-bed and fixed-bed operations. As a result, the swelling and caking characteristics of certain coals make them less suitable for use as feedstock in applications where swelling and/or caking is undesired. Therefore, various studies have focused on the manipulation of the swelling and/or caking propensity of coals, and have proven the viability of using additives to reduce the swelling and caking of powdered coal (<500 μm). However, there is still a lack of research specifically focused on large coal particle devolatilisation behaviour, particularly swelling and caking, and the reduction thereof using additives. A comprehensive study was therefore proposed to investigate the swelling and caking behaviour of large coal particles (5, 10, and 20 mm) of typical South African coals, and the influence of the selected additive (potassium carbonate) thereon. Three different South African coals were selected based on their Free Swelling Index (FSI): coal TSH is a high swelling coal (FSI 9) from the Limpopo province, GG is a medium swelling coal (FSI 5.5-6.5) from the Waterberg region, and TWD is a non-swelling coal (FSI 0) from the Highveld region. Image analysis was used to semi-quantitatively describe the transient swelling and shrinkage behaviour of large coal particles (-20+16 mm) during lowtemperature devolatilisation (700 °C, N2 atmosphere, 7 K/min). X-ray computed tomography and mercury submersion were used to quantify the degree of swelling of large particles, and were compared to conventional swelling characteristics of powdered coals. The average swelling ratios obtained for TWD, GG, and TSH were respectively 1.9, 2.1 and 2.5 from image analysis and 1.8, 2.2 and 2.5 from mercury submersion. The results showed that coal swelling measurements such as FSI, and other conventional techniques used to describe the plastic behaviour of powdered coal, can in general not be used for the prediction of large coal particle swelling. The large coal particles were impregnated for 24 hours, using an excess 5.0 M K2CO3 impregnation solution. The influence of K2CO3-addition on the swelling behaviour of different coal particle sizes was compared, and results showed that the addition of K2CO3 resulted in a reduction in swelling for powdered coal (-212 μm), as well as large coal particles (5, 10, and 20 mm). For powdered coal, the addition of 10 wt.% K2CO3 decreased the free swelling index of GG and TSH coals from 6.5 to 0 and from 9.0 to 4.5, respectively. The volumetric swelling ratios (SRV) of the 20 mm particles were reduced from 3.0 to 1.8 for the GG coal, and from 5.7 to 1.4 for TSH. In contrast to the non-swelling (FSI 0) behaviour of the TWD powders, the large particles exhibited average SRV values of 1.7, and was found not be influenced by K2CO3-impregnation. It was found that the maximum swelling coefficient, kA, was reduced from 0.025 to 0.015 oC-1 for GG, and from 0.045 to 0.027 oC-1 for TSH, as a results of impregnation. From the results it was concluded that K2CO3-impregnation reduces
the extent of swelling of coals such as GG (medium-swelling) and TSH (high-swelling),
which exhibit significant plastic deformation. Results obtained from the caking experiments indicated that K2CO3-impregnation influenced the physical behaviour of the GG coal particles (5, 10, and 20 mm) the most. The extent of caking of GG was largely reduced due to impregnation, while the wall thickness and porosity also decreased. The coke from the impregnated GG samples had a less fluid-like
appearance compared to coke from the raw coal. Bridging neck size measurements were performed, which quantitatively showed a 25-50% decrease in the caking propensity of GG particles. Coal TWD did not exhibit any caking behaviour. The K2CO3-impregnation did not influence the surface texture or porosity of the TWD char, but increased the overall brittleness of the devolatilised samples. Both the extent of caking and porosity of TSH coke were not influenced by impregnation. However, impregnation resulted in significantly less and smaller opened pores on the surface of the devolatilised samples, and also reduced the average wall thickness of the TSH coke.
The overall conclusion made from this investigation is that K2CO3 (using solution
impregnation) can be used to significantly reduce the caking and swelling tendency of large coal particles which exhibits a moderate degree of fluidity, such as GG (Waterberg region). The results obtained during this investigation show the viability of using additive addition to reduce the caking and swelling tendency of large coal particles. Together with further development, this may be a suitable method for modifying the swelling and caking behaviour of specific coals for use in fixed-bed and fluidised-bed gasification operations. / PhD (Chemical Engineering), North-West University, Potchefstroom Campus, 2015
|
3 |
High-Pressure Oxidation Rates for Large Coal and Char ParticlesMathias, James A. 01 December 1996 (has links)
The main objective of this study was to investigate the factors that influence the oxidation rate of large (five to eight millimeters in diameter) coal and char particles. To accomplish this, experiments were performed in which the gas temperature, gas velocity, particle size, partial pressure of oxygen, and total pressure were varied. The experiments were performed with the cantilever balance attachment and the high pressure controlled profile reactor.
Approximately 90 combustion experiments were performed with Pittsburgh, Utah Blind Canyon, and Wyodak-Anderson coal. These experiments were performed at atmospheric pressure with air and varied gas temperature, gas velocity, and particle size. Following the experiments performed with coal, approximately 70 experiments were performed with char made from Pittsburgh coal. These experiments varied all the environmental conditions mentioned above as well as partial pressure of oxygen and total pressure.
After the experiments were completed, the data were analyzed and the following conclusions were made. An increase in the partial pressure of oxygen dramatically increased the oxidation rate when the total pressure remained constant. The oxidation rate was only slightly affected when the partial pressure of oxygen was raised by increasing the total pressure. The oxidation rate dramatically decreased when the partial pressure of oxygen was held constant and the total pressure was raised. The oxidation rate noticeably increased when the initial mass of the particle was decreased. The gas temperature and gas velocity did not affect the oxidation rate greatly for the experiments performed with coal. The oxidation rate increased for the experiments performed with char at the high gas temperature and high gas velocity conditions.
|
4 |
Modelling Simulation and Statistical Studies of Primary Fragmentation of Coal Particles Subjected to Detonation WavePatadiya, Dharmeshkumar Makanlal January 2015 (has links) (PDF)
Coal is likely to remain an important energy source for the next several hundred years
and hence advances in coal combustion technologies have major practical impact. Detonation combustion of coal initiated by a plasma cartridge driven detonation wave holds
promise for improving both system and combustion efficiencies. Both fragmentation and chemical kinetic pathways are qualitatively different in comparison to conventional coal combustion. The present work is a theoretical investigation of fragmentation due to detonation wave. The theoretical simulation starts with simple model and progressively incorporates more realistic analysis such as combined convective and radiative boundary
condition. It studies the passing of detonation wave on coal particles suspended in air.
Concepts of solid mechanics are used in analysing fragmentation of coal particles. A
numerical model is developed which includes stress developed due to both thermal and
volatilization effects. Weibull statistical analysis is used to predict the fracture time and fracture location resulting from principal stress induced. It is observed that coal particles fragment within microseconds. Radiation does not have much effect on developed stress. Volatilization does not have much effect on fragmentation for the particle size considered in this work and stress due to thermal effect dominated the fragmentation.
Coal size distribution statistics is considered to obtain real regime. Coal is used as mixture of different sized particles in real combustors. Hence it is important to analyse the effect of detonation wave on mixture of coal particles. Results presented in this work from simulation run suggest that plasma assisted detonation initiated technology can fragment coal particles faster. Average fracture time of mixture of coal particles is far less than detonation travel time for the detonation tube considered here. Simulation results suggest that almost 90% of coal particles fragment early. Average fracture time reduces as Mach number increases. Same phenomena can be observed for volatile matter generated at fracture and ow of volatile matter at fracture. Hence it can be concluded that plasma assisted detonation combustion leads to different volatilization and fragmentation pathways.
|
5 |
A Numerical Study of the Gas-Particle Flow in Pipework and Flow Splitting Devices of Coal-Fired Power PlantSchneider, Helfried, Frank, Thomas, Pachler, Klaus, Bernert, Klaus 17 April 2002 (has links) (PDF)
In power plants using large utility coal-fired boilers for generation of electricity the coal is pulverised in coal mills and then it has to be pneumatically transported and distributed to a larger number of burners (e.g. 30-40) circumferentially arranged in several rows around the burning chamber of the boiler. Besides the large pipework flow splitting devices are necessary for distribution of an equal amount of pulverised fuel (PF) to each of the burners. So called trifurcators (without inner fittings or guiding vanes) and ''riffle'' type bifurcators are commonly used to split the gas-coal particle flow into two or three pipes/channels with an equal amount of PF mass flow rate in each outflow cross section of the flow splitting device. These PF flow splitting devices are subject of a number of problems. First of all an uneven distribution of PF over the burners of a large utility boiler leads to operational and maintenance problems, increased level of unburned carbon and higher rates of NOX emissions. Maldistribution of fuel between burners caused by non uniform concentration of the PF (particle roping) in pipe and channel bends prior to flow splitting devices leads to uncontrolled differences in the fuel to air ratio between burners. This results in localised regions in the furnace which are fuel rich, where insufficient air causes incomplete combustion of the fuel. Other regions in the furnace become fuel lean, forming high local concentrations of NOX due to the high local concentrations of O2. Otherwise PF maldistribution can impact on power plant maintenance in terms of uneven wear on PF pipework, flow splitters as well as the effects on boiler panels (PF deposition, corrosion, slagging).
In order to address these problems in establishing uniform PF distribution over the outlet cross sections of flow splitting devices in the pipework of coal-fired power plants the present paper deals with numerical prediction and analysis of the complex gas and coal particle (PF) flow through trifurcators and ''riffle'' type bifurcators. The numerical investigation is based on a 3-dimensional Eulerian- Lagrangian approach (MISTRAL/PartFlow-3D) developed by Frank et al. The numerical method is capable to predict isothermal, incompressible, steady gas- particle flows in 3-dimensional, geometrically complex flow geometries using boundary fitted, block-structured, numerical grids. Due to the very high numerical effort of the investigated gas-particle flows the numerical approach has been developed with special emphasis on efficient parallel computing on clusters of workstations or other high performance computing architectures. Besides the aerodynamically interaction between the carrier fluid phase and the PF particles the gas-particle flow is mainly influenced by particle-wall interactions with the outer wall boundaries and the inner fittings and guiding vanes of the investigated flow splitting devices. In order to allow accurate quantitative prediction of the motion of the disperse phase the numerical model requires detailed information about the particle-wall collision process. In commonly used physical models of the particle-wall interaction this is the knowledge or experimental prediction of the restitution coefficients (dynamic friction coefficient, coefficient of restitution) for the used combination of particle and wall material, e.g. PF particles on steel.
In the present investigation these parameters of the particle-wall interaction model have been obtained from special experiments in two test facilities. Basic experiments to clarify the details of the particle-wall interaction process were made in a test facility with a spherical disk accelerator. This test facility furthermore provides the opportunity to investigate the bouncing process under normal pressure as well as under vacuum conditions, thus excluding aerodynamically influences on the motion of small particles in the near vicinity of solid wall surfaces (especially under small angles of attack). In this experiments spherical glass beads were used as particle material. In a second test facility we have investigated the real impact of non-spherical pulverised fuel particles on a steel/ceramic target. In this experiments PF particles were accelerated by an injector using inert gas like e.g. CO2 or N2 as the carrier phase in order to avoid dust explosion hazards. The obtained data for the particle-wall collision models were compared to those obtained for glass spheres, where bouncing models are proofed to be valid. Furthermore the second test facility was used to obtain particle erosion rates for PF particles on steel targets as a function of impact angles and velocities.
The results of experimental investigations has been incorporated into the numerical model. Hereafter the numerical approach MISTRAL/PartFlow-3D has been applied to the PF flow through a ''riffle'' type bifurcator. Using ICEM/CFD-Hexa as grid generator a numerical mesh with approximately 4 million grid cells has been designed for approximation of the complex geometry of the flow splitting device with all its interior fittings and guiding vanes. Based on a predicted gas flow field a large number of PF particles are tracked throughout the flow geometry of the flow-splitter. Besides mean quantities of the particle flow field like e.g. local particle concentrations, mean particle velocities, distribution of mean particle diameter, etc. it is now possible to obtain information about particle erosion on riffle plates and guiding vanes of the flow splitting device. Furthermore the influence of different roping patterns in front of the flow splitter on the uniformness of PF mass flow rate splitting after the bifurcator has been investigated numerically.
Results show the efficient operation of the investigated bifurcator in absence of particle roping, this means under conditions of an uniform PF particle concentration distribution in the inflow cross section of the bifurcator. If particle roping occurs and particle concentration differs over the pipe cross section in front of the bifurcator the equal PF particle mass flow rate splitting can be strongly deteriorated in dependence on the location and intensity of the particle rope or particle concentration irregularities. The presented results show the importance of further development of efficient rope splitting devices for applications in coal-fired power plants. Numerical analysis can be used as an efficient tool for their investigation and further optimisation under various operating and flow conditions.
|
6 |
A Numerical Study of the Gas-Particle Flow in Pipework and Flow Splitting Devices of Coal-Fired Power PlantSchneider, Helfried, Frank, Thomas, Pachler, Klaus, Bernert, Klaus 17 April 2002 (has links)
In power plants using large utility coal-fired boilers for generation of electricity the coal is pulverised in coal mills and then it has to be pneumatically transported and distributed to a larger number of burners (e.g. 30-40) circumferentially arranged in several rows around the burning chamber of the boiler. Besides the large pipework flow splitting devices are necessary for distribution of an equal amount of pulverised fuel (PF) to each of the burners. So called trifurcators (without inner fittings or guiding vanes) and ''riffle'' type bifurcators are commonly used to split the gas-coal particle flow into two or three pipes/channels with an equal amount of PF mass flow rate in each outflow cross section of the flow splitting device. These PF flow splitting devices are subject of a number of problems. First of all an uneven distribution of PF over the burners of a large utility boiler leads to operational and maintenance problems, increased level of unburned carbon and higher rates of NOX emissions. Maldistribution of fuel between burners caused by non uniform concentration of the PF (particle roping) in pipe and channel bends prior to flow splitting devices leads to uncontrolled differences in the fuel to air ratio between burners. This results in localised regions in the furnace which are fuel rich, where insufficient air causes incomplete combustion of the fuel. Other regions in the furnace become fuel lean, forming high local concentrations of NOX due to the high local concentrations of O2. Otherwise PF maldistribution can impact on power plant maintenance in terms of uneven wear on PF pipework, flow splitters as well as the effects on boiler panels (PF deposition, corrosion, slagging).
In order to address these problems in establishing uniform PF distribution over the outlet cross sections of flow splitting devices in the pipework of coal-fired power plants the present paper deals with numerical prediction and analysis of the complex gas and coal particle (PF) flow through trifurcators and ''riffle'' type bifurcators. The numerical investigation is based on a 3-dimensional Eulerian- Lagrangian approach (MISTRAL/PartFlow-3D) developed by Frank et al. The numerical method is capable to predict isothermal, incompressible, steady gas- particle flows in 3-dimensional, geometrically complex flow geometries using boundary fitted, block-structured, numerical grids. Due to the very high numerical effort of the investigated gas-particle flows the numerical approach has been developed with special emphasis on efficient parallel computing on clusters of workstations or other high performance computing architectures. Besides the aerodynamically interaction between the carrier fluid phase and the PF particles the gas-particle flow is mainly influenced by particle-wall interactions with the outer wall boundaries and the inner fittings and guiding vanes of the investigated flow splitting devices. In order to allow accurate quantitative prediction of the motion of the disperse phase the numerical model requires detailed information about the particle-wall collision process. In commonly used physical models of the particle-wall interaction this is the knowledge or experimental prediction of the restitution coefficients (dynamic friction coefficient, coefficient of restitution) for the used combination of particle and wall material, e.g. PF particles on steel.
In the present investigation these parameters of the particle-wall interaction model have been obtained from special experiments in two test facilities. Basic experiments to clarify the details of the particle-wall interaction process were made in a test facility with a spherical disk accelerator. This test facility furthermore provides the opportunity to investigate the bouncing process under normal pressure as well as under vacuum conditions, thus excluding aerodynamically influences on the motion of small particles in the near vicinity of solid wall surfaces (especially under small angles of attack). In this experiments spherical glass beads were used as particle material. In a second test facility we have investigated the real impact of non-spherical pulverised fuel particles on a steel/ceramic target. In this experiments PF particles were accelerated by an injector using inert gas like e.g. CO2 or N2 as the carrier phase in order to avoid dust explosion hazards. The obtained data for the particle-wall collision models were compared to those obtained for glass spheres, where bouncing models are proofed to be valid. Furthermore the second test facility was used to obtain particle erosion rates for PF particles on steel targets as a function of impact angles and velocities.
The results of experimental investigations has been incorporated into the numerical model. Hereafter the numerical approach MISTRAL/PartFlow-3D has been applied to the PF flow through a ''riffle'' type bifurcator. Using ICEM/CFD-Hexa as grid generator a numerical mesh with approximately 4 million grid cells has been designed for approximation of the complex geometry of the flow splitting device with all its interior fittings and guiding vanes. Based on a predicted gas flow field a large number of PF particles are tracked throughout the flow geometry of the flow-splitter. Besides mean quantities of the particle flow field like e.g. local particle concentrations, mean particle velocities, distribution of mean particle diameter, etc. it is now possible to obtain information about particle erosion on riffle plates and guiding vanes of the flow splitting device. Furthermore the influence of different roping patterns in front of the flow splitter on the uniformness of PF mass flow rate splitting after the bifurcator has been investigated numerically.
Results show the efficient operation of the investigated bifurcator in absence of particle roping, this means under conditions of an uniform PF particle concentration distribution in the inflow cross section of the bifurcator. If particle roping occurs and particle concentration differs over the pipe cross section in front of the bifurcator the equal PF particle mass flow rate splitting can be strongly deteriorated in dependence on the location and intensity of the particle rope or particle concentration irregularities. The presented results show the importance of further development of efficient rope splitting devices for applications in coal-fired power plants. Numerical analysis can be used as an efficient tool for their investigation and further optimisation under various operating and flow conditions.
|
Page generated in 0.2532 seconds