The objective of this research is developing a new method of design for cold-formed steel framed shear wall sheathed by ¾" thick USG structural panel concrete subfloor using a predictive analytical model and comparing the results obtained from the model with those achieved from real testing to verify the analytical model and predicted lateral load-carrying capacity resulted from that. Moreover, investigating the impact of various screw spacings on shear wall design parameter such as ultimate strength, yield strength, elastic stiffness, ductility ratio and amount of energy dissipation is another purpose of this research.

Web crippling is a form of localized buckling that occurs at points of transverse concentrated loading or supports of thin-walled structural members. The theoretical computation of web crippling strength is quite complex as it involves a large number of factors such as initial imperfections, local yielding at load application and instability of web. The existing design provision in North American specification for cold-formed steel C-sections (AISI S100, 2007) to calculate the web-crippling strength is based on the experimental investigation. The objective of this research is to extend the direct strength method to the web crippling strength of cold-formed steel C-sections. ABAQUS is used as a main tool to apply finite element analysis and is used to do the elastic buckling analysis. The work was carried out on C-sections under interior two flange (ITF) loading, end two flange (ETF) loading cases. Total of 128 (58 ITF, 70 ETF) sections were analyzed. Sections with various heights (3.5 in.to 6 in.) and various lengths (21 in. to 36 in.) were considered. Data is collected from the tests conducted in laboratory and the data from the previous researches is used, to extend the direct strength method to cold formed steel sections. Proposing a new design for both the loading cases and calculation of the resistance factors under (AISI S100, 2007) standards is done.

The cold-formed steel framed shear walls with steel sheets and wood-based sheathing are both code approved lateral force resisting system in light-framed construction. In the United States, the current design approach for cold-formed steel shear walls is capacity-based and developed from full-scale tests. The available design provisions provide nominal shear strength for only limited wall configurations. This research focused on the development of analytical models of cold-formed steel framed shear walls with steel sheet and wood-based sheathing to predict the nominal shear strength of the walls at their ultimate capacity level. Effective strip model was developed to predict the nominal shear strength of cold-formed steel framed steel sheet shear walls. The proposed design approach is based on a tension field action of the sheathing, shear capacity of sheathing-to-framing fastener connections, fastener spacing, wall aspect ratio, and material properties. A total of 142 full scale test data was used to verify the proposed design method and the supporting design equations. The proposed design approach shows consistent agreement with the test results and the AISI published nominal strength values. Simplified nominal strength model was developed to predict the nominal shear strength of cold-formed steel framed wood-based panel shear walls. The nominal shear strength is determined based on the shear capacity of individual sheathing-to-framing connections, wall height, and locations of sheathing-to-framing fasteners. The proposed design approach shows a good agreement with 179 full scale shear wall test data. This analytical method requires some efforts in testing of sheathing-to-framing connections to determine their ultimate shear capacity. However, if appropriate sheathing-to-framing connection capacities are provided, the proposed design method provides designers with an analytical tool to determine the nominal strength of the shear walls without conducting full-scale tests.

A prototype rigid wall relocatable shelter was designed and constructed using cold-formed steel (CFS) construction techniques including shear walls with corrugated sheathings. The design of the shelter was to be mechanically sound with adequate thermal performance and resistance to corrosion. Modeling of structural shear walls was performed using ABAQUS and verified with experimental results. At the project's conclusion, a completed full-scale prototype shelter was constructed.

In order to predict the strength of shear wall with cold-formed steel framing members, analytical models were reviewed. Multiple analytical models were studied, as well as twenty-one connection tests were performed. The connection tests consist of 50-ksi cold-formed steel framing track, different fastening configurations, and different sheathing thicknesses (1/8" and 1/2"). No.12 screw resulted in the highest peak load of all fastening configurations, while the rivet connection had the lowest peak load. In addition, failure modes were observed after conducting the connection tests including shear in fastening, screw pullout, and bearing in the sheathing. However, only the rivet and No.10 screw fastening configurations were used in the prediction analysis of the shear wall by the elastic model. Six shear wall tests were conducted on both panels (1/2"and 1/8" thickness). After doing the comparison between the experimental and the elastic model, the percentage difference for the 1/8" and the 1/2" polymer composite panels (3''along the edge and 6''along the chord stud), was very small. It was 6.2% for the 1/8" and 2.96% for the 1/2" panels. This means the analytical model can predict the shear wall peak load. However, the percentage difference was slightly higher being 7.4% for the 1/2" polymer composite panels with 6" along the perimeter with the 12" at the chord stud. After comparing the experimental values to the predicted value of shear walls, it was concluded that this model is the most appropriate analytical method for predicting the shear wall capacity framed with cold-formed steel sheathed with polymer composite panels. Many of these configurations were used in a prototype shelter that was constructed and built at the structural testing laboratory at the University of North Texas.

The use of cold-formed steel (CFS) structures has become increasingly popular in different fields of building technology. For example, small housing systems using cold-formed steel for wall structures, framing systems and roof structures, including trusses and shielding materials, have been developed during recent years. The reasons behind the growing popularity of these products include their ease of fabrication, high strength/weight ratio and suitability for a wide range of applications. These advantages can result in more cost-effective designs, as compared with hot-rolled steel, especially in short-span applications. It has been common practice in cold-formed steel construction to cut openings in the web of beams for the passage of service ducts and piping. The provision of such openings reduces the story heights and consequently can result in saving of considerable amount of construction materials. On the other hand, the presence of a large web opening causes localized redistribution of stress around the opening region. The large opening causes loss of strength and changes the buckling characteristics of an entire member. It also affects the flexural stiffness, resulting in poor performance of member under serviceability. It is common practice to reinforce the opening of hot-rolled steel members, but proper reinforcement schemes for CFS perforated members has not been established yet. Various reinforcement schemes for cold-formed steel sections were investigated during this study. Two types of reinforcement schemes (for flexural zones and shear zones) were developed. Fifty-four flexural tests and 33 shear tests were conducted. Two types of sections (lipped channel joists with h/t ratio 180 and 118) were tested in flexure and one type of section (lipped channel joists with h/t ratio 180) was tested in shear. The study also included a finite element based numerical investigation, consisting of parametric studies on the size (web depth and thickness) of joists, size and shape of web openings, reinforcement and associated fastening schemes. It was observed that a 75 percent of opening in the web of CFS channel joist causes up to 25 percent reduction in flexural strength and up to 60 percent reduction in shear strength. Such reduced flexural and shear strengths were re-captured by providing proper reinforcement schemes. The flexural reinforcement schemes recommended by the current AISI Standard were found to be ineffective for the sections having low w /t ratios. Bridging channel reinforcement scheme was also considered in this study. Bridging channel reinforcement scheme was capable of restoring the flexural strength of cold formed steel joist having w /t ratios 118 and 180. Similarly, the reinforcement schemes recommended in AISI Standard were not adequate to restore the shear strength of joist sections. A newly developed Virendeel type reinforcement system was capable of restoring the original shear strength of a cold-formed steel joist section. / Thesis / Doctor of Philosophy (PhD)

Master of Science / Department of Architectural Engineering and Construction Sciences / Kimberly Waggle Kramer / Bill Zhang / Cold-formed steel members quickly are becoming a popular material for both commercial and residential construction around the world. Their high strength to weight ratio makes them a viable alternative to timber framing. In most cases cold-formed steel is used as a repetitive member in floor, wall, or roof assemblies. Structural sheathing is used in conjunction with the framing members in order to transfer loads between individual members. This sheathing is connected mechanically to the cold-formed steel through a variety of methods. The most common method uses screws spaced at close intervals, usually between 6 to 12 inches on center. When such assemblies are constructed, load is transferred from the sheathing through the connectors into the cold-formed steel, forming a composite assembly in which load is transferred and shared between two materials, providing a higher strength and stiffness over individual members themselves. The amount of load that can be transferred is dependent on the amount of slip that occurs when the assembly is loaded. This slip value describes the amount of composite action that takes place in the assembly. The amount of slip can be described by a value called the slip modulus. The composite, or effective, bending stiffness can be calculated using the slip modulus. In current design of cold-formed steel composite assemblies this composite action is not being taken into account due to a lack of research and understanding of the composite stiffness present in these assemblies. Taking composite action into account can lead to decreased member sizes or increased spacing of members, thereby economizing design. Furthermore, improved understanding of the effective stiffness can lead to more accurate design for vibrations in floor systems. This thesis tests cold-formed steel plywood composite members in an effort to verify previously established slip modulus values for varying steel thicknesses and establishes new values for varying fastener spacings. The slip modulus values obtained are used to calculate effective bending stiffness values in an effort to prove that composite action should be utilized in design of cold-formed steel composite assemblies.

Master of Science / Civil Engineering / Hani G. Melhem / Bill Zhang / Composite action is the joint behavior of two elements connected or bonded together. It is a phenomenon that is utilized in several applications throughout engineering. Previous studies have shown that cold formed steel (CFS) sheathed with structural wood panels exhibits a degree of partial composite action behavior. However currently in the design process, CFS and wood sheathing systems are considered separately in a non-composite manner due to the absence of sufficient supporting data. These systems can include the floors, roofs, and walls of a building. In order to determine the level of composite action present, the slip modulus is needed. The slip modulus describes the relationship between the shear force and the displacement exhibited by two elements in a composite system. The scope of this research is to determine the influence of fastener spacing on the slip modulus and provide a foundation of information to fully define the composite action between CFS and wood sheathing.

In recent years, light gauge cold-formed steel members have been used extensively in low and mid- rise residential building construction. In cold-formed steel design there are several applications where built-up box girders are used to resist load induced in a structure when a single section is not sufficient to carry the design load. The cold-formed steel box girders may be subjected to eccentric loading when the web of one of the sections receives the load and transfers it through the connection to another section. There may be an unequal distribution of load in built-up girder assemblies loaded from one side. In the current North American Specification for the Design of Cold-Formed Steel Structural Members (CSA-S136-01, 2001), there is no guideline or design equation to calculate the flexural capacity of this type of section. AISI cold-formed steel framing design guide (2002) has recommended that the moment of resistance and inertia of the built-up section are the simple addition of the component parts, based on deflection compatibility of the two sections. However, this design approximation has not been justified by any experimental or numerical study. Very little information was found in literature about this topic. The objective of this study is the investigation of the flexural behaviour of built-up box girders assembled from cold-formed stud and track sections when subjected to eccentric loading. Finite element analysis is conducted for this purpose, being much more economical than expensive experimental testing. Detailed parametric studies are carried out to identify the factors affecting the flexural capacity of built-up cold-formed steel sections. The parametric results are used to develop a design equation for calculating the flexural capacity of built-up cold-formed steel sections.

Vibrations associated with lightweight floor systems, as a serviceability criterion, are not well addressed in current residential construction practice. Cold-formed steel floor systems are usually lighter and have less inherent damping. If designers are going to use the current span deflection criteria when designing residential floor systems, it is imperative to find the construction and design details that will limit these annoying vibrations in cold-formed steel floor systems. Presented in this seminar are the results from a recent laboratory study and field study on the vibration characteristics of cold-formed steel floors performed at the University of Waterloo. Several full-scale floor systems with varying construction and design details were constructed and tested, and several in situ floor systems were tested. The objectives of this research were: to evaluate the dynamic response of residential floor systems supported by cold-formed steel joists; to investigate the influence of span length, joist types, subfloor materials, toppings, ceilings, strongbacks, live loads and framing conditions on the vibration characteristics of cold-formed steel floor systems; to identify the critical construction details that will limit annoying floor vibrations; to compare the vibration characteristics of in situ floor systems and laboratory constructed floor systems; and to evaluate the vibration performance of laboratory and in situ floor systems based on current acceptability criteria.