Spelling suggestions: "subject:"combustion -- 3research"" "subject:"combustion -- 0research""
11 |
Experimental investigation of smoldering combustion of cellulosic materialsOrtiz Molina, Marcos German January 1976 (has links)
Thesis. 1976. Mech.E.--Massachusetts Institute of Technology. Dept. of Mechanical Engineering. / Microfiche copy available in Archives and Engineering. / Includes bibliographical references. / by Marcos G. Ortiz Molina. / Mech.E.
|
12 |
Laminar burning velocity of isooctane-air, methane-air, and methanol-air mixtures at high temperature and pressureMetghalchi, M. (Mohamad) January 1977 (has links)
Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 1977. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / by Mohamad Metghalchi. / M.S.
|
13 |
Nonlinear combustion instability in liquid propellant rocket enginesPowell, Eugene Alexander 12 1900 (has links)
No description available.
|
14 |
Effect of sulphur dioxide and fuel sulphur on nitrogen oxide emissionsEkmann, James M. January 1975 (has links)
No description available.
|
15 |
An experimental and numerical investigation of a gas turbine research combustorMorris, Reuben Montresor 12 January 2007 (has links)
Gas turbine engineering faces many challenges in the constant strive to increase not only the efficiency of engines but also the various stages of development and design. Development of combustors have primarily consisted of empirical or semi-empirical modelling combined with experimental investigations. Due to the associated costs and development time a need exists for an alternative method of development. Although experimental investigations can never be substituted completely, mathematical models incorporating numerical methods have shown to be an attractive alternative to conventional combustor design methods. The purpose of this study is twofold: firstly, to experimentally investigate the physical properties associated with a research combustor that is geometrically representative of practical combustors; and secondly, to use the experimental measurements for the validation of a computational fluids dynamic model that was developed to simulate the research combustor using a commercial code. The combustor was tested at atmospheric conditions and is representative of practical combustors that are characterized by a turbulent, three-dimensional flow field. The single can combustor is divided into a primary, secondary and dilution zone, incorporating film¬cooling air through stacked rings and an axial swirler centred around the fuel atomizer. Measurements at different air/fuel ratios captured the thermal field during operating conditions and consisted of inside gas, liner wall and exit gas temperatures. An investigation of the different combustion models available, led to the implementation of the presumed-PDF model of unpremixed turbulent reaction. The computational grid included the external and internal flow field with velocity boundary conditions prescribed at the various inlets. Two-phase flow was not accounted for with the assumption made that the liquid fuel is introduced into the combustion chamber in a gas phase. Experimental results showed that incomplete combustion occurs in the primary zone, thereby reducing the overall efficiency. Also evident from the results obtained are the incorrect flow splits at the various inlets. Evaluation of the numerical model showed that gas temperatures inside the combustor are overpredicted. However, the numerical model is capable of capturing the correct distributions of temperatures and trends obtained experimentally. This study is successful in capturing detail temperature measurements that will be used for validation purposes to assist the development of a numerical model that can accurately predict combustion properties. / Dissertation (M Eng (Mechanical Engineering))--University of Pretoria, 2007. / Mechanical and Aeronautical Engineering / unrestricted
|
16 |
Simulation of an algorithm for the active control of combustion noiseCapelle, Jean-Yves 25 April 2009 (has links)
The simulation of an algorithm for the active control of combustion noise generated by a turbulent flame produced by an open burner is developed in this thesis. The simulation includes (1) an autoregressive model of real combustion noise, (2) a feedback loop based on the "observer" method, (3) a model of the transfer function between the acoustic driver and the sensor through the flame, and (4) a method to take into account the time-delay due the calculation of the algorithm. A practical implementation of the control strategy is also proposed.
An attenuation of up to 40 dB is obtained in the 0 - 3000 Hz band, decreasing with the time-delay required for creation of the feedback signal. The influence of the order of the autoregressive model is studied, and it is shown that better results are obtained by increasing the order. The choices for the location of the activator and for the type of sensor are investigated and discussed. Further analytical research on the method of computing the feedback signal in the presence of time-delay is identified. / Master of Science
|
17 |
Investigation of air control on chunkwood combustorMoscahlaidis, George 10 June 2012 (has links)
Many small scale agricultural operations such as greenhouses, peanut drying and tobacco curing, use significant quantities of thermal energy. Direct combustion of biomass is a potential source of heat energy for those agricultural applications to substitute for the electricity or fossil fuels (principally LP gas) currently used. However, small scale combustion equipment often operates with low efficiency and high emissions. A prototype chunkwood combustor was installed and tested. The basis for controlling heat output, was the modulation of air supplied to the primary and secondary combustors. Exhaust gas CO and CO₂ concentrations, combustor efficiency, and useful heat output were measured. The cleanest burn was achieved during a forty minute test, where 50 percent of stoichiometric air was introduced at the primary, and 170 percent at the secondary, for a total of 220 percent stoichiometric. The overall average CO/CO₂ ratio for this test was 0.084, and 0.1 is considered to be an average rating for a combustion in a wood stove. Moreover, the efficiency during this test was 52 percent. / Master of Science
|
18 |
Initiation of smoldering combustion in flexible polyurethane foamsMak, Audie Y. K January 1980 (has links)
Thesis (Mech.E)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 1980. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / by Audie Y.K. Mak. / Mech.E
|
19 |
A low-frequency instability mechanism in a coaxial dump combustorKeklak, John Adam January 1982 (has links)
Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Mechanical Engineering, 1982. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / by John Adam Keklak. / M.S.
|
20 |
Combustion of liquid fuels in a Rijke type pulse combustorBai, Tiejun 05 1900 (has links)
No description available.
|
Page generated in 0.1146 seconds