No

No / This paper presents a numerical investigation into the behaviour of headed shear stud in composite beams with profiled metal decking. A three-dimensional finite element model was developed using general purpose finite element program ABAQUS to study the behaviour of through-deck welded shear stud in the composite slabs with trapezoidal deck ribs oriented perpendicular to the beam. Both static and dynamic procedures were investigated using Drucker Prager model and Concrete Damaged Plasticity model respectively. In the dynamic procedure using ABAQUS/Explicit, the push test specimens were loaded slowly to eliminate significant inertia effects to obtain a static solution. The capacity of shear connector, load-slip behaviour and failure modes were predicted and validated against experimental results. The delamination of the profiled decking from concrete slab was captured in the numerical analysis which was observed in the experiments. ABAQUS/Explicit was found to be particularly suitable for modelling post-failure behaviour and the contact interaction between profiled decking and concrete slabs. It is concluded that this model represents the true behaviour of the headed shear stud in composite beams with profiled decking in terms of the shear connection capacity, load-slip behaviour and failure modes.

No

no / The design of multi-storey buildings in the UK, in the past, considered steel and concrete structures in isolation. Today, designers utilize the combined properties of steel and concrete in the form of composite or hybrid structures as a more attractive efficient alternative. Designers of steel structures acknowledge that the presence of concrete slabs may be designed compositely with steel beams in order to increase both flexural strength and stiffness at virtually no extra cost, except for the headed shear studs. The use of composite construction with precast hollowcore slabs has become one of the most popular construction methods in the UK. Currently, design of composite construction is covered by BS5950, Part 3, but will soon be replaced by the new European Standard, Eurocode 4. However, design of composite construction with precast hollowcore slabs is currently outside the provisions of this new code. In this paper, an overview of the Eurocode 4 structure and its contents are first presented and some of the particular issues that affect this new form of construction will be given. Design guidance using the Eurocode methodology will also be presented.

This thesis summarizes the results of an experimental investigation involving the testing of push-out specimens with channel shear connectors. The test program involved the testing of 78 push-out specimens and was aimed at the development of new equations for channel shear connectors embedded in solid concrete slabs and slabs with wide ribbed metal deck oriented parallel to the beam. <p>The test specimens were designed to study the effect of a number of parameters on the shear capacity of channel shear connectors. Six series of push-out specimens were tested in two phases. The primary difference between the two phases was the height of the channel connector. Other test parameters included the compressive strength of concrete, the length and the web thickness of the channel. <p>Three different types of failure mechanisms were observed. In specimens with higher strength concrete, failure was caused by the fracture of the channel near the fillet with the channel web acting like a cantilever beam. Crushing-splitting of concrete was the observed mode of failure in specimens with solid slabs when lower strength concrete was used. In most of the specimens with metal deck slabs, a concrete shear plane type of failure was observed. In the specimens involving this type of failure, the channel connector remained intact and the concrete contained within the flute in front of channel web sheared off along the interface. <p>The load carrying capacity of a channel connector increased almost linearly with the increase in channel length. On average, the increase was about 39% when the channel length was increased from 50 mm to 100 mm. There was a further increase of 24% when the channel length was increased from 100 mm to 150 mm. The influence of web thickness of channel connector was significant when the failure occurred due to channel web fracture but was minimal for a concrete crushing-splitting type of failure. <p>The specimens with solid concrete slabs carried higher load compared to those with metal deck slabs. The increase in load capacity was 33% for specimens with 150 mm long channels but only 12% for those with 50 mm long channel connectors. <p>This investigation resulted in the development of a new equation for predicting the shear strength of channel connectors embedded in solid concrete slabs. The proposed equation provides much better correlation to test results than those obtained using the current CSA equation. <p>The results of specimens with metal deck slabs were used to develop a new equation for predicting the shear capacity of channel connectors embedded in slabs with metal deck oriented parallel to the beam. The values predicted by the proposed equation were in good agreement with the observed test values.

This thesis summarizes the results of an experimental investigation involving the testing of push-out specimens with channel shear connectors. The test program involved the testing of 78 push-out specimens and was aimed at the development of new equations for channel shear connectors embedded in solid concrete slabs and slabs with wide ribbed metal deck oriented parallel to the beam. <p>The test specimens were designed to study the effect of a number of parameters on the shear capacity of channel shear connectors. Six series of push-out specimens were tested in two phases. The primary difference between the two phases was the height of the channel connector. Other test parameters included the compressive strength of concrete, the length and the web thickness of the channel. <p>Three different types of failure mechanisms were observed. In specimens with higher strength concrete, failure was caused by the fracture of the channel near the fillet with the channel web acting like a cantilever beam. Crushing-splitting of concrete was the observed mode of failure in specimens with solid slabs when lower strength concrete was used. In most of the specimens with metal deck slabs, a concrete shear plane type of failure was observed. In the specimens involving this type of failure, the channel connector remained intact and the concrete contained within the flute in front of channel web sheared off along the interface. <p>The load carrying capacity of a channel connector increased almost linearly with the increase in channel length. On average, the increase was about 39% when the channel length was increased from 50 mm to 100 mm. There was a further increase of 24% when the channel length was increased from 100 mm to 150 mm. The influence of web thickness of channel connector was significant when the failure occurred due to channel web fracture but was minimal for a concrete crushing-splitting type of failure. <p>The specimens with solid concrete slabs carried higher load compared to those with metal deck slabs. The increase in load capacity was 33% for specimens with 150 mm long channels but only 12% for those with 50 mm long channel connectors. <p>This investigation resulted in the development of a new equation for predicting the shear strength of channel connectors embedded in solid concrete slabs. The proposed equation provides much better correlation to test results than those obtained using the current CSA equation. <p>The results of specimens with metal deck slabs were used to develop a new equation for predicting the shear capacity of channel connectors embedded in slabs with metal deck oriented parallel to the beam. The values predicted by the proposed equation were in good agreement with the observed test values.

No / This paper presents analytical technique and simplified formulas for the calculations of cracking, yield and ultimate moments of different cases as well as deflections of ECC-concrete composite beams reinforced with steel bars. The technique is based on the simplified constitutive models of materials, strain compatibility, perforce bond of materials and equilibrium of internal forces and moment. Experimental testing of eleven ECC-concrete composite beams reinforced with steel bars is also presented. All beams tested had the same geometrical dimensions but different steel reinforcement strength and ECC thickness. The proposed formulas showed good agreement with the experimental results of various moment values and deflections. A parametric analysis shows that yield and ultimate moments increase with the increase of concrete strength in case of compression failure but, essentially, remain unchanged in case of tensile failure. With increasing the tensile resistance, for example by increasing ECC height replacement ratio, reinforcement ratio, strength of steel reinforcement and ECC, ultimate curvature and energy dissipation increase in case of tensile failure and decrease in case of compressive failure. On the other hand, ductility and energy dissipation ratio decrease with the increase of reinforcement ratio and strength, but, essentially, remain unchanged with increasing the height replacement ratio and strength of ECC. / National Natural Science Foundation of China (51678514, 51308490), the Natural Science Foundation of Jiangsu Province, China (BK20130450), Six Talent Peaks Project of Jiangsu Province (JZ-038, 2016), Graduate Practice Innovation Project of Jiangsu Province (SJCX17-0625) and the Jiangsu Government Scholarship for Overseas Studies.

Yes / Experimental and theoretical investigations on the flexural performance of steel reinforced ECC-concrete composite beams subjected to freeze–thaw cycles are presented in this paper. Four groups of reinforced composite beams with different ECC height replacement ratios subject to 0, 50, 100 and 150 cycles of freeze–thaw were physically tested to failure. Experimental results show that the bending capacity decreases with the increase of freeze–thaw cycles regardless of ECC height replacement ratios. However, the ultimate moment, stiffness and durability of ECC specimens and ECC-concrete composite specimens are greater than those of traditional concrete specimens, owing to the excellent tensile performance of ECC materials. With the increase of ECC height, the crack width and average crack spacing gradually decrease. According to materials’ constitutive models, compatibility and equilibrium conditions, three failure modes with two boundary failure conditions are proposed. Simplified formulas for the moment capacity are also developed. The results predicted by the simplified formulas show good agreement with the experimental moment capacity and failure modes. A parametric analysis is conducted to study the influence of strength and height of ECC, amount of reinforcement, concrete strength and cycles of freeze–thaw on moment capacity and curvature ductility of ECC-concrete composite beams.

Yes / For composite cellular beams, additional deflections occur due to the loss of bending and shear stiffness at the opening positions and also due to slip in the shear connectors caused by partial shear connection. Design formulae are presented for the additional deflection of composite beams with circular openings or for cellular beams as a function of the proportionate depth of the openings. The simplified formulae are calibrated against finite element results for both cellular and solid web beams and also against measured deflections of a 15.3 m composite cellular beam test. This additional deflection is presented as a function of flexural and shear terms that are a function of the span:depth ratio. For modelling of cellular beams to determine deflections, the circular opening may be represented by an equivalent rectangular opening of length equal to 70% of the opening diameter.

Yes / This paper presents test results of fifteen reinforced engineered cementitious composite (ECC)-concrete beams. The main parameters investigated were the amount and type of reinforcement, and ECC thickness. All reinforced ECC-concrete composite beams tested were classified into four groups according to the amount and type of main longitudinal reinforcement used; three groups were reinforced with FRP, steel and hybrid FRP/steel bars, respectively, having similar tensile capacity, whereas the fourth group had a larger amount of only FRP reinforcement. In each group, four height replacement ratios of ECC to concrete were studied. The test results showed that the moment capacity and stiffness of concrete beams are improved and the crack width can be well controlled when a concrete layer in the tension zone is replaced with an ECC layer of the same thickness. However, the improvement level of ECC-concrete composite beams was controlled by the type and amount of reinforcement used. Based on the simplified constitutive relationships of materials and plane section assumption, three failure modes and their discriminate formulas are developed. Furthermore, simplified formulas for moment capacity calculations are proposed, predicting good agreement with experimental results. / National Natural Science Foundation of China (51678514, 51308490), the Natural Science Foundation of Jiangsu Province, China (BK20130450), Six Talent Peaks Project of Jiangsu Province (JZ-038, 2016), Graduate Practice Innovation Project of Jiangsu Province (SJCX17-0625), the Jiangsu Government Scholarship for Overseas Studies and Top-level Talents Support Project of Yangzhou University.