published_or_final_version / Civil Engineering / Master / Master of Philosophy

No description available.

No description available.

published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy

published_or_final_version / Civil Engineering / Doctoral / Doctor of Philosophy

published_or_final_version / abstract / Civil Engineering / Master / Master of Philosophy

Abstract not available

Thesis (Ph.D.)--McMaster University, 2004. / Advisor: Ahmed Ghobarah. Includes bibliographical references (p. 341-351). Also available online.

The results of an experimental investigation are presented which examine the seismic adequacy of pre-1970 reinforced concrete (RC) corner beam-column joints and the efficacy of carbon fiber-reinforced polymer (CFRP) composites for both pre- and post-earthquake retrofit of such joints. Four full-scale corner beam-column-slab subassemblages built with identical dimensions and pre-1970 reinforcement details were subjected to a reverse-cycle bidirectional displacement history consisting of alternate and simultaneous cycles in the two primary frame directions before and/or after retrofit. Two of the specimens were first subjected to severe and moderate levels of damage, respectively, then repaired by epoxy injection, and strengthened by adding a #7 reinforcing bar within the clear cover at the column inside corner and by externally bonding multiple layers of carbon fabric to form a carbon-epoxy retrofit system. Two other specimens, one of which had a significantly lower concrete compressive strength, were strengthened in their as-built condition. The CFRP scheme was improved in light of the findings as the experimental program progressed. Pre-1970 RC corner beam-column joints were found to be severely inadequate in meeting seismic demands because of column bar yielding, joint shear failure, loss of anchorage of beam bottom bars, failure of column lap-splices, and the resulting loss of stiffness and strength that dominate their behavior even at relatively low interstory drift levels. Bidirectional loading played a significant role in such response. It was shown, however, that such joints can be strengthened easily both before and after earthquake damage by using CFRP composite schemes. Regardless of the level of existing damage and concrete strength, a "rigid" joint behavior up to interstory drift ratios of at least 2.4% and joint shear strength factors ranging from 1.06 to 1.41√MPa were achieved; such shear strength factors are larger than the value of 1.00√MPa recommended for use with seismically designed, code-conforming corner beam-column joints. A ductile beam hinging mechanism was achieved and energy dissipation capacity was improved efficiently for joints with concrete strengths ranging from 26 to 34 MPa. The subassemblage with significantly low-strength concrete (15 MPa) had low overall lateral stiffness and reduced reinforcement anchorages which prevented the formation of beam hinging. In cases of such low-strength concrete, more invasive operations may be required so that the improved joint shear strength can be mobilized. It is recommended that bidirectional loading be always considered in both pre- and post-retrofit evaluation of corner joints.

This research investigated the behavior of nonseismically detailed reinforced concrete exterior beam-column joints subjected to bidirectional lateral cyclic loading using nonlinear finite element analysis (NLFEA). Beam-column joints constitute a critical component in the load path of reinforced concrete buildings due to their fundamental role in integrating the overall structural system. Earthquake reconnaissance reports reveal that failure of joints has contributed to partial or complete collapse of reinforced concrete buildings designed without consideration for large lateral loads, resulting in significant economic impact and loss of life. Such infrastructure exists throughout seismically active regions worldwide, and the large-scale risk associated with such deficiencies is not fully known. Computational strategies provide a useful complement to the existing experimental literature on joint behavior and are needed to more fully characterize the failure processes in seismically deficient beam-column joints subjected to realistic failure conditions. Prior to this study, vulnerable reinforced concrete corner beam-column joints including the slab had not been analyzed using nonlinear finite element analysis and compared with experimental results. The first part of this research focused on identification and validation of a constitutive modeling strategy capable of simulating the behaviors known to dominate failure of beam-column joints under cyclic lateral load using NLFEA. This prototype model was formulated by combining a rotating smeared crack concrete constitutive model with a reinforcing bar plasticity model and nonlinear bond-slip formulation. This model was systematically validated against experimental data, and parametric studies were conducted to determine the sensitivity of the response to various material properties. The prototype model was then used to simulate the cyclic response of four seismically deficient beam-column joints which had been previously evaluated experimentally. The simulated joints included: a one-way exterior joint, a two-way beam-column exterior corner joint, and a series of two-way beam-column-slab exterior corner joints with varying degrees of seismic vulnerability. The two-way corner joint specimens were evaluated under simultaneous cyclic bidirectional lateral and cyclic column axial loading. For each specimen, the ability of the prototype model to capture the strength, stiffness degradation, energy dissipation, joint shear strength, and progressive failure mechanisms (e.g. cracking) was demonstrated.