Spelling suggestions: "subject:"increasecorrosion"" "subject:"contactcorrosion""
31 |
Unpowered wireless sensors for structural health monitoringAndringa, Matthew 28 August 2008 (has links)
Not available / text
|
32 |
Evaluation of external post-tensioned tendons using vibration signaturesLee, Jun Ki, 1975- 28 August 2008 (has links)
Recent findings regarding corrosion of post-tensioned bridges have highlighted the urgent need to develop reliable methods to predict the behavior of the structural system after damage has occurred and inspection techniques to assess the condition of the structure. Corrosion in strands is undesirable in that it often progresses without visual signs of distress, but may cause a brittle failure. To complicate the inspection, access to the strands for visual inspection is usually blocked by the concrete cross section. To date, significant efforts have been taken to improve the durability of the post-tensioned bridges. However, the behavior of the post-tensioned bridges with corrosion damage is not clearly understood and the currently available inspection techniques tend to provide only limited information about the nature and extent of the damage. The research project discussed in this dissertation was developed is to evaluate the feasibility of using the vibration technique to detect and estimate the extent of damage in an external tendon due to corrosion. To accomplish this goal, damage was induced in five specimens, which were monitored periodically to correlate the measured changes in the frequency response to the level of damage. The induced damage simulated the degradation of a post-tensioned structure from corrosion. This dissertation describes the experimental program and the numerical scheme used to estimate the condition of the specimens. Three types of specimens were tested during the experimental phase of the research: individual strands, cables specimens, and external tendons. A series of tension tests of individual strands were conducted to investigate changes in the uniaxial behavior after damage was induced. Simulated damage included uniform corrosion of the strand, mechanical wire cuts, and an initial defect in one wire. Three cable specimens and one tendon specimen were subjected to fatigue loading. The loading was selected to simulate the loss of cross-sectional area in the strands, and also caused grout damage. The frequency response of the specimens was recorded periodically during the fatigue tests and acoustic sensors were used to detect the occurrence of wire breaks. A second tendon specimen was exposed to an acid solution to simulate the hydrogen induced cracking in the strand at three different locations along the length of the specimen. A number of wires fractured during the exposure test and damage was inspected visually. Natural frequencies were also measured periodically. The residual prestressing force in of the specimens was extracted from the measured natural frequencies. The stiff string model was used to determine optimum values of tension and flexural stiffness from the frequency response. The numerical results from this optimization demonstrated the feasibility of using the vibration technique as a nondestructive testing method for external tendons.
|
33 |
Coupled passive resonant circuits as battery-free wireless sensorsPasupathy, Praveenkumar 24 January 2011 (has links)
Detection and monitoring of the damage created by the corrosion of the steel reinforcement in concrete structures is a challenging and multidisciplinary problem. Economical monitoring strategy that is long-term and nondestructive requires low-cost, battery-free, wireless sensors. Our Electronic Structural Surveillance (ESS) platform uses battery-free passive resonant circuit (tag) as a sensor. The tag is magnetically coupled to an external reader coil. It is interrogated/read remotely in a non-contact (wireless) manner and the state of the sensor is determined from a swept frequency impedance measurement. When paired with the correct sensing element (transducer), the tag can be used for a variety of sensing applications for example, chemical & biochemical sensors. A circuit model of the reader and tag for such a universal battery-free wireless sensor platform is developed. The interaction between design and detection limit is examined. The dependence of the measured signal strength and read range on the various reader and tag circuit parameters is analyzed. Since the values of the circuit of the coils are dependent on their geometries, the effect of specific coil geometry is evaluated and design recommendations are made. / text
|
34 |
Reliability assessment of flexural cracking resistance of reinforced concrete retaining structuresCho, Wah-fu, Gordon, 曹華富 January 1979 (has links)
published_or_final_version / Civil Engineering / Master / Master of Philosophy
|
35 |
A time to cracking model for critically contaminated reinforced concrete structuresPeterson, J. Eric 04 August 2009 (has links)
In addressing the need for a site specific corrosion model for concrete structures, Bazant’s time to first cracking model was used as the basis for an experimental research study. The theoretical model, which expresses the time to first cracking as a function of the corrosion rate and physical properties of the reinforced concrete, was never experimentally validated. This research study focuses on examining Bazant’s model and its validity using commercially available corrosion rate measuring devices. With validation of the model, the present condition of the structure could be assessed, damage rate predicted, and repair or rehabilitation methods selected.
The experimental program examined 18 test blocks and 52 test slabs constructed to simulate sections of a reinforced concrete bridge deck. The test blocks and slabs contained a single layer of electronically isolated steel reinforcement embedded below the surface of the specimens. The design variables included cover depth, bar spacing, bar diameter, and corrosion rate. Six chloride concentrations 0.0 to 9.6 lb/yd³ (0.0 to 5.7 kg/m³) added directly to the fresh concrete were used to vary the corrosion rate. Two environmental conditions were also considered: outdoors in Blacksburg, Virginia and indoors with near constant moisture and temperature. The slabs were designed with two reinforcing mats. The lower mat of fiberglass reinforcement was placed in both directions and the upper mat was one layer of fiberglass and one layer of steel. Thus, the corrosion rate a single layer of electrically isolated steel bars was monitored.
The corrosion rates were monitored from the date of casting for approximately one year using the 3LP and Gecor corrosion rate devices. The amount of metal loss of the bars was determined both destructively and non-destructively to allow a comparison between the two. The metal losses were compared to the predictions made according to Bazant’s equations as well as to other existing time to first cracking criteria to determine their validity. Tests were performed to verify the chloride contents of the slabs. The effect of temperature on the corrosion rate was also investigated. Preliminary results indicate that temperature strongly influences the corrosion rate.
To date no cracks have formed in the surface of the test specimens. The corrosion rate of the slabs has been progressing at a maximum rate of 1.24 mils/yr (31.5 microns/yr) for over one year. The test blocks and slabs are to be monitored until cracking occurs at which time Bazant’s model will be either validated or adjusted to reflect the predictions derived from the commercially available corrosion rate devices used in this experimental program. Additional tests must also be performed to further quantify the effects of temperature and other variables. / Master of Science
|
36 |
The development of a field procedure for determining the chloride content of concrete and an analysis in the variability of the effective diffusion constantHerald, Stephen Estel January 1989 (has links)
During the initial phase of the investigation, four methods were selected for investigation from a review of literature sources,the specific ion probe, spectrophotometer, digital titrator, and Quantab titrator strips.
The initial results from the laboratory testing procedure and evaluation based on cost, speed, accuracy, and level of expertise required indicated the specific ion probe was more suitable for use in the field when compared to the remaining methods selected.
Effects of cement content and reaction temperature on the results obtained for the specific ion probe were also investigated. Results of the tests for the effects of cement content were somewhat inconclusive, but indicated more variability in the results as the amount of chloride present in the specimens increased. However, correlation between the increase in variability and i cement content was not indicated. The specific ion probe is affected by differences in temperature and the appropriate correction factor for the variation was determined.
Field validation of the procedure was undertaken to substantiate the findings from the laboratory investigation. This was accomplished by subjecting the specific ion probe to testing specimens from bridges located in different exposure groups within the United States. Four bridges were tested for chloride content in Pennsylvania. Following this initial phase, three bridges were tested in Virginia, Florida, and Wisconsin respectively.
An analysis of the variability in the effective diffusion constant for the bridges tested was also performed to determine any relationships which exist between different exposure groups and to determine effects of time. / Master of Science
|
37 |
The effect of South African quaternary supplementary cementitious blends on corrosion behaviour of concrete reinforcement in chloride and Sulphate mediaAkinwale, Abiodun Ebebezer 10 1900 (has links)
The aim of this study was to assess the strength, durability properties and corrosion resistance of concrete samples using supplementary cementitious blended materials. In this investigation, three supplementary concrete materials (SCMs) were used together with ordinary Portland Cement (OPC) to form cementitious blends at different proportions. The supplementary materials are silica fume (SF), ground granulated blast furnace slag (GGBS) and fly ash (FA). Sixteen (16) different proportions of the cementitious blends were produced. Tests carried out on concrete samples include slump test, compressive strength, oxygen permeability, sorptivity, porosity, chloride conductivity test, resistance to chloride and sulphate attack. The electrode potentials of tested samples were also observed using electrochemical measurements.
Concrete specimens prepared with 10%, 20%, 30%, 40%, up to 60% of blended cements replacement levels were evaluated for their compressive strength at, 7, 14, 28, 90 and 120 days while the specimens were evaluated for durability tests at 28, and 90 days respectively. The results were compared with ordinary Portland cement concrete without blended cement. Voltage, and temperature measurements were also carried out to understand the quality of concrete. The corrosion performance of steel in reinforced concrete was studied and evaluated by electrochemical half-cell potential technique in both sodium chloride, and magnesium sulphate solutions respectively. The reinforced concrete specimens with centrally embedded 12mm steel bar were exposed to chloride and sulphate solutions with the 0.5 M NaCl and MgSO4 concentrations respectively. An impressed voltage technique was carried out to evaluate the corrosion resistance of the combination of quaternary cementitious blended cement, so as to get the combination with optimum performance. Improvement of strength, durability, and corrosion resistance properties of blended concrete samples are observed at different optimum percentages for binary, ternary and quaternary samples. The effect of cementitious blends is recognized in limiting the corrosion potential of the tested SCM concrete samples. Generally, the cementitious blends with limited quantity of SF to 10% have the potential to produce satisfactory concrete. These should however be used for low cost construction, where high quality concrete is not required. / Civil and Chemical Engineering / M. Tech. (Chemical Engineering)
|
38 |
Evaluation of Chloride Threshold for Steel Fiber Reinforced Concrete Composited in Aggressively Corrosive EnvironmentsUnknown Date (has links)
Highway drainage pipes utilize concrete reinforced with steel wire to help mitigate water,
earth, and traffic loads. Drainage pipes reinforced with zinc electroplated steel fibers
offer a lower steel alternative to traditional steel wire cage reinforcements. The objective
of the thesis research was to determine the physical and electrochemical characteristics of
zinc electroplated steel fiber corrosion propagation. Experimental programs include:
Fracture analysis of zinc electroplated steel fibers embedded in dry-cast concrete pipes
exposed to varying chloride concentrations; Visual analysis of zinc electroplated steel
fibers embedded in concrete exposed to varying chloride concentrations; Electrochemical
analysis of zinc electroplated steel fibers embedded in concrete exposed to varying
chlorides; Chloride threshold determination for zinc electroplated steel fibers immersed
in simulated pore solution. Between the four experimental programs the most significant
conclusion is that oxygen, moisture, and chlorides past the chloride threshold must be
present for corrosion to propagate significantly on the zinc electroplated steel fibers. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2016. / FAU Electronic Theses and Dissertations Collection
|
39 |
Concrete diffusivity and its correlation with chloride deposition rate on concrete exposed to marine environmentsUnknown Date (has links)
The aim of this study was to investigate the diffusion of chloride ions into concrete samples that were exposed in scenarios that simulate the splash, tidal, atmospheric, and immersed portions of a marine structure. To study the atmospheric deposition, the project also investigated the relationship between chloride ion deposition on the wet candle and its accumulation into concrete samples. Results from the wet candle experiment indicated that between 2% and 45% of the chlorides deposited per square meter of exposed area could be found within the concrete samples. After 6 months, slag G1a blocks showed the most resistance to chloride penetration in the tidal and splash simulations. After 10 months of exposure, fly ash samples had the slowest rates of diffusion in the tidal simulation while the fly ash + silica fume samples and the slag samples measured similar rates of diffusion within the tidal zone. After 90 days of curing, cylinders composed of 20% fly ash & 8% silica fume measured the highest average resistivity values and were found to be less vulnerable to chloride ion penetration than the 20% fly ash and the 50% slag concrete through rapid migration tests. / by Victor Anthony Echevarria. / Thesis (M.S.C.S.)--Florida Atlantic University, 2012. / Includes bibliography. / Mode of access: World Wide Web. / System requirements: Adobe Reader.
|
40 |
Experimental evaluation of the durability of fly ash-based geopolymer concrete in the marine environmentUnknown Date (has links)
The construction industry is increasingly turning to the use of environmentally friendly materials in order to meet the sustainable aspect required by modern infrastructures. Consequently, for the last two decades, the expansion of this concept, and the increasing global warming have raised concerns on the extensive use of Portland cement due to the high amount of carbon dioxide gas associated with its production. The development of geopolymer concretes offers promising signs for a change in the way of producing concrete. However, to seriously consider geopolymer binders as an alternative to ordinary Portland cement, the durability of this new material should be evaluated in any comparative analysis. The main purpose of this study was to evaluate the durability characteristics of low calcium fly ash-based geopolymer concretes subjected to the marine environment, compared to ordinary Portland cement concrete with similar exposure. To achieve this goal, 8 molar geopolymer, 14 molar geopolymer and ordinary Portland cement concrete mixes were prepared and tested for exposure in seawater. Compressive strengths in the range of 2900 to 8700 psi (20-60 MPa) were obtained. The corrosion resistance performance of steel-reinforced concrete beams, made of these mixes, was also studied, using an accelerated electrochemical method, with submergence in salt water. The test results indicated that the geopolymer concrete showed excellent resistance to chloride attack, with longer time to corrosion cracking, compared to ordinary Portland cement concrete. / by Jean-Baptiste Edouard. / Thesis (M.S.C.S.)--Florida Atlantic University, 2011. / Includes bibliography. / Electronic reproduction. Boca Raton, Fla., 2011. Mode of access: World Wide Web.
|
Page generated in 0.0888 seconds