Spelling suggestions: "subject:"contactarea ratio"" "subject:"kontaktarea ratio""
1 |
On the running-in of gearsSjöberg, Sören January 2010 (has links)
<p>The general trend in gear industry, today, is an increased focus on gear transmission efficiency. Gear transmission efficiency losses arise from loaded and unloaded gear contacts, seals, lubricant and bearings. One way of minimising the losses is to lower the lubricant viscosity. This will reduce the speed dependent losses. However, the load dependent losses might increase. To avoid this, the ratio between lubricant film thickness and surface roughness must be maintained, which can be fulfilled by producing smoother gear surfaces. As a starting point for this realisation process, the present manufacturing processes, the design tools and the characteristics of the gear flank interface must be further investigated and developed. This must be achieved with an emphasis on economic production.</p><p>This thesis focuses on our understanding of how different gear manufacturing methods —particularly the contribution of the running-in process—affect the surface characteristics, with the view of increasing gearbox efficiency. The thesis consists of a summary and three appended papers.</p><p>Paper A and paper B discuss the relationship between design parameters and real gear wheel surfaces manufactured with different manufacturing methods. The research hypothesis was that the contact area ratio is a descriptive parameter for the contact condition. Paper A deals with the influence of manufacturing method on the initial contact conditions and also serves as a validation of the simulation program used. The emphasis in Paper B is the changes that occur during running-in, and to correlate these changes to design requirements. Paper C approaches the influences of manganese phosphate-coating and lubricants with respect to friction and the risk of scuffing at the initial contact.</p><p>The main conclusions of this thesis are that the contact area ratio presents a descriptive measure of how surface topography influences the contact, seen at both a global (form deviation) and local (roughness) level. The surface topography caused by the manufacturing method has a significant influence on the contact area ratio. This is an important result, since neither national standards nor commercially available gear evaluation programs handle surface topography on the local scale. Shaving was found to have the highest contact area ratio, and should therefore be the best choice if deviations from case hardening could be minimised. It is also confirmed that gear-like surfaces coated with manganese phosphate have a low coefficient of friction, and raise the limiting load for scuffing failure enormously compared to the ground equivalent.</p> / QC 20100518 / KUGG / Sustainable gear transmission realization
|
2 |
Long-term observation of rock fracture permeability and structure under various pressure and temperature conditions / 様々な拘束圧および温度条件下での岩盤不連続面構造と透水性の長期観測Song, Chenlu 23 March 2020 (has links)
京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第22420号 / 工博第4681号 / 新制||工||1731(附属図書館) / 京都大学大学院工学研究科都市社会工学専攻 / (主査)教授 岸田 潔, 教授 三村 衛, 准教授 肥後 陽介 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM
|
3 |
Seismic Energy Dissipation, Self-Centering, and Settlement of Rocking Foundations: Analysis of Experimental Data with Comparisons to Numerical ModelingSoundararajan, Sujitha January 2019 (has links)
The major objective of this study is to correlate the rocking foundation performance parameters with their capacity parameters and earthquake demand parameters using the results obtained from 142 centrifuge and shaking table experiments. It is found that seismic energy dissipation and permanent settlement of rocking foundations correlate well with rocking coefficient and Arias intensity of the earthquake, whereas the maximum moment and peak rotation of the foundation correlate well with peak ground acceleration. A numerical model, using the contact interface model available in OpenSees, is developed to simulate the performance of rocking foundations, and it is validated using experimental results. Though the numerical model predicts the moment capacity, seismic energy dissipation, and tipping-over stability of rocking foundations reasonably well, the model appears to overpredict the settlement of foundations. Furthermore, a parametric study showed that settlement reduces as initial vertical stiffness increases and is directly proportional to peak ground displacement.
|
4 |
On the running-in of gearsSjöberg, Sören January 2010 (has links)
The general trend in gear industry, today, is an increased focus on gear transmission efficiency. Gear transmission efficiency losses arise from loaded and unloaded gear contacts, seals, lubricant and bearings. One way of minimising the losses is to lower the lubricant viscosity. This will reduce the speed dependent losses. However, the load dependent losses might increase. To avoid this, the ratio between lubricant film thickness and surface roughness must be maintained, which can be fulfilled by producing smoother gear surfaces. As a starting point for this realisation process, the present manufacturing processes, the design tools and the characteristics of the gear flank interface must be further investigated and developed. This must be achieved with an emphasis on economic production. This thesis focuses on our understanding of how different gear manufacturing methods —particularly the contribution of the running-in process—affect the surface characteristics, with the view of increasing gearbox efficiency. The thesis consists of a summary and three appended papers. Paper A and paper B discuss the relationship between design parameters and real gear wheel surfaces manufactured with different manufacturing methods. The research hypothesis was that the contact area ratio is a descriptive parameter for the contact condition. Paper A deals with the influence of manufacturing method on the initial contact conditions and also serves as a validation of the simulation program used. The emphasis in Paper B is the changes that occur during running-in, and to correlate these changes to design requirements. Paper C approaches the influences of manganese phosphate-coating and lubricants with respect to friction and the risk of scuffing at the initial contact. The main conclusions of this thesis are that the contact area ratio presents a descriptive measure of how surface topography influences the contact, seen at both a global (form deviation) and local (roughness) level. The surface topography caused by the manufacturing method has a significant influence on the contact area ratio. This is an important result, since neither national standards nor commercially available gear evaluation programs handle surface topography on the local scale. Shaving was found to have the highest contact area ratio, and should therefore be the best choice if deviations from case hardening could be minimised. It is also confirmed that gear-like surfaces coated with manganese phosphate have a low coefficient of friction, and raise the limiting load for scuffing failure enormously compared to the ground equivalent. / <p>QC 20100518</p> / KUGG / Sustainable gear transmission realization
|
Page generated in 0.0913 seconds