Fundação de Amparo a Pesquisa do Estado de Minas Gerais / This work was to study the influence of the magnetic field on the reduction of hexavalent chromium, removal of COD and total chromium, addition of cell growth in batch (batch reactor), using a mixed culture from located in a tanning city of Franca-SP (AMCOA). The influence of static magnetic field generated by a device that produces an electric current through a conductor, producing a magnetic field around the conductor, like a magnet. This equipment produces a magnetic field pulsed square wave of constant intensity and frequency. In the first step of adjusting the mixed cultures of chromium VI obtained a promising response. Thereafter, a preliminary test was performed to analyze the behavior of the influence of the magnetic field in the reduction of chromium VI and diameter of the reactor, obtaining 71% reduction of chromium VI with a larger diameter, without the presence of magnetic field has seen a reduction of 53%, with an initial concentration of 100 mg/l of chromium and a time of 4 hours of process. In other stages of the project, performing the tests with different frequencies of the magnetic field (1,2,5 and 10 Hz) and doing an analysis related to cell death of micro-organisms, showed that for frequencies of 10 Hz, there was cell death presents some cultures, which was confirmed in a lower frequency. The results were satisfactory when used in a magnetic field frequency of 5 Hz, maximal reduction of chromium VI reducing the time about 4 hours of processing, better removal of COD and total chromium using a volume of 500 ml and concentration of 100 mg/l initial chromium. Checking the influence of different frequency magnetic field, the initial effluent volumes (300 and 1000 ml) and initial concentration of chromium VI (50, 150 and 200 mg/l). The higher the initial concentration the lower the chromium reduction of chromium VI, larger volumes and a reduction of chromium VI and removal of COD and total chromium is not as significant as the use of smaller volumes. / Neste trabalho foi realizado o estudo da influência do campo magnético sobre a redução de cromo hexavalente, remoção de cromo total e DQO, além do crescimento celular em modo descontínuo (reator batelada), utilizando-se de uma cultura mista proveniente do curtume AMCOA localizado na cidade de Franca-SP. Foi avaliada a influência de campo eletromagnético estático gerado por um equipamento que produz uma corrente elétrica, passando por um condutor, produzindo um campo magnético ao redor do condutor, como se fosse um ímã. Este equipamento produz um campo magnético pulsante com onda quadrática de intensidade e frequência constantes. Na primeira etapa de adaptação das culturas mistas ao cromo VI obteve-se uma resposta promissora. Posteriormente, foi realizado um teste preliminar para analisar o comportamento da influência do campo magnético na redução de cromo VI e diâmetro de reator, obtendo 71% de redução de cromo VI com um maior diâmetro, sem a presença de campo magnético obteve uma redução de 53%, com uma concentração inicial de 100 mg/L de cromo e com um tempo de 4 horas de processo. Nas outras etapas do projeto, realizando os testes com diferentes frequências de campo magnético (1, 2, 5 e 10 Hz) e fazendo uma análise relacionada à morte celular dos micro-organismos, mostrou-se que para frequências de 10 Hz, havia morte celular de algumas culturas presentes, o que não foi verificado em uma frequência menor. Os resultados foram satisfatórios quando se utiliza uma frequência de campo magnético de 5 Hz, com máxima redução de cromo VI reduzindo o tempo em torno de 4 horas de processo, com melhor remoção de cromo total e DQO, utilizando um volume de 500 mL e concentração de 100 mg/L de cromo inicial. Verificando a influência de diferentes frequências de campo magnético, volumes iniciais de efluente (300 e 1000 mL) e concentrações iniciais de cromo VI (50, 150 e 200 mg/L). Quanto maior a concentração inicial de cromo menor foi a redução de cromo VI, e em volumes de efluentes maiores a redução de cromo VI e remoção de cromo total e DQO não foram tão significativas quanto em se aplicar volumes menores. / Mestre em Engenharia Química

A large number of evolutionarily conserved genes have been identified by comparative genomics approaches. However, a considerable fraction of these genes lack functional characterization despite the availability of several bioinformatics approaches for prediction of protein function. Moreover, with the advent of genome sequencing efforts, numerous disease associated genes have been identified. While high throughput approaches aid in identification of genes, studying individual genes is important to understand their cellular roles. During studies on cyclic AMP metabolism in mycobacteria conducted in the laboratory, a Class III cyclic nucleotide phosphodiesterase, Rv0805 was identified from Mycobacterium tuberculosis. Interestingly, additional bioinformatics analysis identified orthologs were in higher eukaryotes. These were members of the metallophosphoesterase-domain-containing protein 1 (MPPED1) and metallophosphoesterase-domain-containing protein 2 (MPPED2) family. Class III cyclic nucleotide phosphodiesterases were previously reported only in prokaryotes and are distinct from Class I cyclic nucleotide phosphodiesterases generally found in eukaryotes. Thus MPPED1 and MPPED2 proteins were the first identified eukaryotic Class III cyclic nucleotide phosphodiesterases. In humans, MPPED2 is located on chromosome 11 in the region p13-14 that has been associated with WAGR (Wilms’ tumor, aniridia, genitourinary anomalies, and mental retardation) syndrome. Inspection of this region across sequenced mammalian genomes has revealed a shared synteny. Most interestingly, a stretch of 200 bp within the coding sequence of MPPED2 is identified to be one of 481 ultra conserved regions within the human genome. Furthermore, orthologs of MPPED2 can be traced all the way back to Drosophila melanogaster and Caenorhabditis elegans. All of these observations indicate that MPPED2 is highly conserved and hints at its likely importance in many organisms. MPPED1 and MPPED2 have been reported to be expressed in adult and fetal brain respectively and have been annotated as metallophosphoesterases. Metallophosphoesterases are a superfamily of proteins that show wide phyletic distribution and exhibit diversity in their substrate utilization and function. Previous studies from the laboratory have shown that MPPED1 and MPPED2 are indeed metallophosphoesterases and demonstrate cyclic nucleotide phosphodiesterase activity. The crystal structure of MPPED2 was obtained in collaboration with Dr. Marjetka Podobnik (National Institute of Chemistry, Slovenia). Interestingly, the crystal structure of MPPED2 revealed the presence of bound 5’GMP molecule at the active site, and this finding was investigated further in this thesis. MPPED2 bound 5’GMP and 5’AMP with high affinity (IC50 of ~70 nM) which inhibited the activity of MPPED2. Key residues involved in stabilising the 5’ nucleotide have been identified by structure guided mutational analysis. The MPPED2-G252H mutant, generated to mimic the active site of MPPED1, also bound 5’GMP or 5’AMP but with much lower affinity. Given the high affinity of MPPED2 towards 5’GMP/5’AMP, it can be speculated that MPPED2 may show poor phosphodiesterase activity in the cell, and could function in a catalytically-independent manner, perhaps as a scaffolding protein. MPPED1 on the other hand may have a catalytic role that could be regulated by intracellular levels of 5’AMP, 5’GMP and their respective cyclic nucleotides. In order to investigate the biological role of the MPPED1/MPPED2 family of proteins, Drosophila melanogaster was chosen as a model organism owing to the presence of a single ortholog, CG16717, in its genome. Biochemical characterization of CG16717 revealed that the protein was in fact a metallophosphodiesterase capable of hydrolysing cyclic AMP and cyclic GMP, albeit poorly. CG16717 could be inhibited by 5’ nucleotides at high concentrations that may seldom be achieved in-vivo, suggesting that CG16717 may have roles in the organism that depend on its catalytic activity. CG16717 has not been functionally characterized previously. In this thesis, a detailed analysis of CG16717 expression pattern has been performed. CG16717 was found to be expressed in all stages of the fly lifecycle. In adult female flies, levels of CG16717 increased across age. Moreover, CG16717 was not differentially regulated under conditions of starvation, paraquat-induced oxidative stress or in the presence of heavy metals. Spatial expression analysis revealed that CG16717 was expressed in all adult tissues tested, with maximal expression in the brain, suggesting that neuronal expression of CG16717 may be important for its function. Attempts to identify specific cells expressing CG16717 using an enhancer-promoter analysis were not successful. In order to elucidate the physiological role of CG16717, and after having ruled out options of using a P-element insertion mutant and RNA interference approaches, a targeted knock-out of CG16717 was generated using homologous recombination based genomic engineering. CG16717KO flies generated were homozygous viable suggesting that CG16717 was dispensable for fly survival at least under normal laboratory conditions. In line with high expression of CG16717 in the brain and in-vitro ability of CG16717 to hydrolyse cAMP and cGMP, CG16717KO flies showed two to three-fold higher levels of cyclic nucleotides in the head fraction than wild-type flies. C25E10.12, one of the three C. elegans orthologs of CG16717 has been identified to be a target of the transcription factor daf-16 (FOXO) that is inhibited by active insulin signalling. Moreover, knock-down of C25E10.12 reduced the lifespan of age-1 (PI3K) mutant worms. In contrast to this, CG16717 was not found to be differentially regulated in dFOXO null flies. CG16717KO flies however, showed median lifespan that was shorter than control wild-type flies even in the presence of functional PI3K. Various genetic approaches were employed to verify if reduced lifespan was indeed a consequence of loss of CG16717. In the first approach, a wild-type copy of CG16717 was re-introduced at the genomic locus of CG16717 in the CG16717KO flies using attP-attB recombination. However, this approach could not rescue the reduced lifespan of CG16717KO flies, probably due to very low expression of CG16717. In the second approach, CG16717 was reconstituted using genomic constructs containing a copy of CG16717. Finally, CG16717 was expressed ubiquitously using the bipartite Gal4/UAS system. Both the genomic construct and the expression of CG16717 using the Gal4/UAS approach were able to restore the lifespan of CG16717KO flies. More importantly, overexpression of CG16717 in an otherwise wild-type fly led to enhanced lifespan over and above that of control flies. All of these together suggested that CG16717 plays a critical role in regulating lifespan. Mutants of the insulin and target of rapamycin (TOR) signalling pathways have previously been reported to show lifespan extension. Moreover, these mutants have also been associated with reduced growth, increased stress resistance and reduced fecundity. Given the reduction in lifespan of CG16717KO flies, the other insulin/TOR signalling associated phenotypes were tested. While CG16717KO flies showed no difference in terms of developmental growth, and resistance to starvation or paraquat induced oxidative stress, CG16717KO flies were less fecund compared to wild-type controls. Multiple approaches were adopted even in the case of reduced fecundity to verify if the observed phenotype was a consequence of loss of CG16717. However, neither reconstitution of CG16717 using the genomic construct nor ubiquitous expression of CG16717 using the bipartite Gal4/UAS system were able to rescue the reduced fecundity phenotype of CG16717KO flies. This suggested that reduced fecundity in CG16717KO flies was probably not linked to CG16717 and was a consequence of a second mutation at a site distinct from CG16717. Two other approaches were employed to confirm these observations. When CG16717KO/Deficiency lines were tested, these showed fecundity comparable to wild-type control flies despite the lack of CG16717. CG16717KO flies were extensively out-crossed in an attempt to segregate the second site mutation from the CG16717 locus and their fecundity was tested. However, these flies which retained the deletion of CG16717, showed fecundity comparable to wild-type control flies, reiterating that reduced fecundity was not linked to loss of CG16717. In an attempt to find possible links between reduced longevity of CG16717KO flies and the well-established insulin/TOR pathways, transcript levels of key players of these pathways were measured by qRT-PCR. The translational repressor 4EBP was found to be upregulated in CG16717KO flies compared to wild-type control flies. Interestingly, increased 4EBP levels have been associated with enhanced lifespan but in this case despite higher levels of 4EBP, CG16717KO flies showed reduced lifespan. Phosphorylation status of 4EBP and other players involved in the insulin/TOR phosphokinase signalling cascade would shed light on the activity of these pathways. In summary, this thesis has attempted to understand the biochemistry and physiological functions of an evolutionarily conserved metallophosphoesterase. Its apparent role in regulating life span in the fly suggests that the functions of this protein are likely to impinge on a number of diverse and important pathways involved in basic physiological processes in the organism. Further investigation would shed light on the molecular basis by which CG16717 affects lifespan, and opens up new avenues to understanding the contributions of CG16717 in regulating lifespan and diverse neurological functions.

This communication reports a unique ultra-large sheet formation through hierarchical self-assembly of a rod–coil graft copolymer containing a rigid polyphenylene backbone and flexible poly(ethylene oxide) (PEO) side chains. The hierarchical self-assembly process involved a distinctive morphological transition of 1D helical to 2D superstructures. The graft copolymer offers a new chance for the challenging bottom-up fabrication of ultra-large self-assembled nanosheets in solution, as well as a novel system for fundamental studies on 2D self-assembly of polymers.

La CO déshydrogénase (CODH) de Desulfovibrio vulgaris est une métalloenzyme qui catalyse la réduction réversible du CO2 en CO. C’est un homodimère composé de deux sites actifs Ni-4Fe-4S et de trois centres fer-soufre. Durant ma thèse, nous avons étudié la maturation de la CODH à nickel et les propriétés catalytiques de la CODH à nickel de D. vulgaris.Pour comprendre le mécanisme de maturation de la CODH à nickel, nous avons caractérisé deux formes de la CODH à nickel produites en présence ou en absence de CooC par des approches biochimiques, spectroscopiques, électrochimiques et cristallographiques. Notre caractérisation montre que la présence de CooC est nécessaire à l’obtention d’une CODH mature et activable. Nous avons également mis en évidence un processus d’activation en présence de nickel dans des conditions réductrices qui n’implique apparemment pas de changement structural du site actif.Notre étude de la CODH à nickel par électrochimie nous a permis de mettre en évidence plusieurs phénomènes d’activations/inactivations de l’enzyme dans des conditions aérobies et anaérobies, et l’existence d’une hétérogénéité fonctionnelle : plusieurs formes de l’enzyme qui montrent des propriétés catalytiques différentes peuvent être présentes simultanément. Cette observation pourrait éclairer d’une façon nouvelle l’hétérogénéité structurale observée par cristallographie et remettre en question les mécanismes proposés sur la base de ces structures. / The monoxide carbon dehydrogenase (CODH) from Desulfovibrio vulgaris is a metalloenzyme which catalyses the reversible reduction of CO2 into CO. It is a homodimer containing two active sites and three iron-sulfur clusters. During my thesis, we studied the maturation of CODH nickel and catalytic properties of Ni-CODH from D. vulgaris.In order to understand, the maturation mechanism of Ni-CODH, we have characterized two forms of Ni-CODH produced in the presence or absence of CooC by biochemical, spectroscopic, electrochemical and crystallographic approaches. Our characterisation shows that the presence of CooC is necessary to obtain a mature Ni-CODH which can be activated. We have also identified an activation process in the presence of nickel in reducing conditions that apparently involves no structural change in the active site.Our study of the Ni-CODH by electrochemistry has shown several phenomena of activation/inactivation of the enzyme under aerobic and anaerobic conditions, and the existence of a functional heterogeneity : several forms of the enzyme which show different catalytic properties may be present simultaneously. This observation could illuminate the structural heterogeneity observed by crystallography and question the proposed mechanisms on the basis of these structures.

This communication reports a unique ultra-large sheet formation through hierarchical self-assembly of a rod–coil graft copolymer containing a rigid polyphenylene backbone and flexible poly(ethylene oxide) (PEO) side chains. The hierarchical self-assembly process involved a distinctive morphological transition of 1D helical to 2D superstructures. The graft copolymer offers a new chance for the challenging bottom-up fabrication of ultra-large self-assembled nanosheets in solution, as well as a novel system for fundamental studies on 2D self-assembly of polymers.

A new dual-boron-cored luminogen ligated with a nitrogen-containing multidentate ligand and four bulky phenyl rings was readily synthesized. The unique molecular structure endows this BN-containing luminogen with rich photophysical properties in either solution or in the solid state, including a large Stokes shift, aggregation induced emission activity and reversible piezochromism. Furthermore, this BN-containing luminogen exhibits good capabilities for imaging living cells and sensing of fluoride anions.

This paper reports a simple self-assembly strategy towards bowl-shaped carbon-containing hollow particles, as well as an unprecedented potential application for block copolymer vesicles in energy storage. Kippah vesicles (fully collapsed vesicles), formed by solution self-assembly of an amphiphilic polystyrene-block-poly(ethylene oxide) block copolymer, were employed as the template to guide the formation of bowl-shaped nitrogen-doped carbon hollow particles (BNCHPs). As electrode materials of supercapacitors, BNCHPs exhibit superior electrochemical performance. In particular, compared with their spherical counterpart, BNCHPs largely increase their volumetric packing density, leading to much higher volumetric capacitance or volume reduction of electrodes, which is desired for practical supercapacitor devices.

This diploma thesis deals with evaluation of efficiency of protection conversion coatings created by passivation metals and alloys in passivation baths without chromium compounds. The theoretical part is initially concerned with question of electrochemical corrosion of metals, consequently there are mentioned different methods of corrosion protection. The main section of theoretical part of this thesis deals with chromate conversion coatings, description of their protective efficiency (including their unique self-healing effect) and then with account of new chromate-free conversion coatings occurring as chromate alternatives, whose usage is constrained because of their content of hexavalent chromium, which is highly toxic, oxidizing and also carcinogenic and thereby very dangerous for human body and the environment. Experimental part of this thesis is concerned with evaluation of efficiency of particular conversion coating which is quite commonly use in some applications as chromate alternative. It is chromate-free conversion coating which is created by passivation of metals or alloys in passivation bath Pragokor BP, which contains zirconium fluorocomplexes and is without any chromium or other toxic or ecologically unhealthy compounds. The influence of sealing of the coating in preparation Pragokor Seal Al and also other surface treatments such as application of conservation wax WAXENG or cold application of zinc coating were tested too. Efficiency of mentioned surface treatments was then evaluated on aluminum and steel by laboratory accelerated and atmospheric corrosion testing.

京都大学 / 0048 / 新制・課程博士 / 博士(医学) / 甲第19174号 / 医博第4016号 / 新制||医||1010(附属図書館) / 32166 / 京都大学大学院医学研究科医学専攻 / (主査)教授 髙橋 淳, 教授 村井 俊哉, 教授 渡邉 大 / 学位規則第4条第1項該当 / Doctor of Medical Science / Kyoto University / DFAM

The germylenes, germanium(II) 2-(oxidomethyl)phenolate (1), germanium(II) 4-methyl-2-(oxidomethyl)phenolate (2) and germanium(II) 4-bromo-2-(oxidomethyl)phenolate (3) were synthesized and their thermally induced twin polymerization to give organic–inorganic hybrid materials was studied. The compounds 1–3 form oligomers including dimers, trimers and tetramers as a result of intermolecular coordination of the benzylic oxygen atom to germanium. The structural motifs were studied by single crystal X-ray diffraction analysis and DFT-D calculations. Thermally induced twin polymerization of these germylenes gave hybrid materials based on germanium-containing phenolic resins. Carbonization of these resins under reductive conditions resulted in porous materials that are composed of germanium and carbon (Ge@C materials), while oxidation with air provided non-porous germanium dioxide. The porous Ge@C materials were tested as potential anode materials for rechargeable Li-ion batteries. Reversible capacities of 540 mA h g−1 were obtained at a current density of 346 mA g−1 without apparent fading for 100 cycles, which demonstrates that germanium is well accessible in the hybrid material. / Dieser Beitrag ist aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.