Contaminated sites are found all around the world. In order to contain these contaminants, engineers propose capping the contaminated sediments with a sand cap. When capping these contaminants, the sand causes consolidation to occur and could cause a slope failure if the contaminants were on a slope. Investigating the properties of these contaminated sediments allows for proper analysis of a slope failure. The primary objective of this research was to determine the shear strength of contaminated sediments. Since soil samples from actual contaminated sites are highly variable and difficult to explain, the soil used in this research project was mixed and controlled in the lab. A mixture of Kaolinite, water and mineral oil (NAPL, non-aqueous phase liquid) was used for the specimens. Different oil amounts were placed into the specimens to create different scenarios. The different oil combinations included: 100% water, 100% oil, 90% oil, 70% oil, and 50% oil. All of the specimens were fully saturated, and the specimens that had less than 100% oil contained water in the remaining percentage. Consolidated Undrained and Consolidated Drained triaxial tests were performed on the specimens. The constructed specimens were subjected to consolidation stages ranging from 0.6psi to 29psi in confining pressure. The main focus of the study was on low confining pressures. After consolidation the specimens were sheared either undrained or drained. Both tests were utilized in order to see the difference in the pore pressures generated. Failure envelopes were developed for the different oil contents that contained three dimensions included the shear strength, the effective stress, and the pore pressure difference between the pore oil pressures and the pore water pressures. Also, the behavior of oil-dominated versus water-dominated was determined. Results from the 100% water specimens were comparable to previous data. The shear strength for the 100% oil specimens was higher than the 100% water specimens, but lower than the 90% oil and 70% oil specimens. The 50% oil specimens resulted in a great deal of variability on whether the specimen was water-dominated or oil-dominated. The main conclusion was that the Kaolinite had an increase in strength with the introduction of mineral oil. / text

Der Sprengstoff PETN ist äußerst schwer zu detektieren. Ein verbesserter anti-PETN-Antikörper wurde durch Anwendung des Bioisosterie-Konzepts entwickelt. Diese polyklonalen IgGs sind sehr selektiv und sensitiv. Die Nachweisgrenze des ELISAs beträgt 0,15 µg/L. Der Messbereich des Immunoassays liegt zwischen 1 und 1000 µg/L. Die Antikörper sind recht pH-stabil als auch robust gegen Lösungsmittelzusätze. Für die Umweltanalytik von TNT wurde eine HPLC-kompatible Affinitätssäule mit porösem Glas als Trägermaterial hergestellt. Um die anti-TNT-Antikörper selektiv aus den TNT-Seren zu isolieren, wurde eine Trennung an einer Dinitrophenyl-Affinitätssäule durchgeführt. Zur Optimierung der Kopplungsmethode wurden orangefarbene Dabsyl-Proteine synthetisiert und auf der Oberfläche gebunden. Die Färbung wurde als Indikator für die Ligandendichte verwendet. Wegen der hohen Affinitätskonstanten der anti-TNT-IgGs lässt sich TNT nicht reversibel von der TNT-Affinitätssäule eluieren. Daher wurde eine neuartige Elutionsmethode entwickelt, die thermische Online-Elution. Die maximale Kapazität einer TNT- Affinitätssäule betrug 650 ng TNT bzw. 10 µg/mL Säulenvolumen. Um die Ligandendichte der TNT-Affinitätssäulen zu bestimmen, wurde ein neues Verfahren entwickelt, da die spektroskopischen Proteinbestimmungsmethoden nicht geeignet waren. Zur Proteinbestimmung wurde eine HPLC-Trennung der Aminosäuren Tyr und Phe ohne vorherige Derivatisierung entwickelt. Die Proteinhydrolysezeit wurde durch Einsatz einer Mikrowelle von 22 h auf 30 min verkürzt. Zur internen Kalibrierung wurden HTyr und FPhe verwendet. Die Nachweisgrenze bei 215 nm ist sowohl für Tyr als auch für Phe 0,05 µM (~ 10 µg/L). Dieses neue Verfahren, das als Aromatische Aminosäureanalyse (AAAA) bezeichnet werden kann, wurde zur Proteinbestimmung von homogenen Proben mit NIST-BSA validiert, wobei die Nachweisgrenze für Proteine 16 mg/L (~ 300 ng BSA) ist. Die relative Standardabweichung incl. der Hydrolysestufe beträgt 5%. / The explosive Pentaerythritol tetranitrate (PETN) is extremely difficult to detect. An improved antibody against PETN was developed by using the bioisosteric concept. These polyclonal antibodies are highly selective and sensitive. The limit of detection (LOD) of the ELISA was determined to be 0.15 µg/L. The dynamic range of the assay was found to be between 1 and 1000 µg/L. The antibodies are sufficiently pH-stable and resistant to solvent additives. An HPLC-compatible TNT-affinity column with porous glass as support material was prepared for the environmental analysis. In order to isolate the anti-TNT antibodies of the TNT sera a separation was carried out on a dinitrophenyl-affinity column. To optimize the immobilization method, orange-coloured dabsyl proteins were synthesized and bound to the surface. The colour intensity was found to be an indicator for the immobilization rate. In consequence of the high affinity constants of the anti-TNT antibodies, TNT can''t elute by a typical acidic elution step. Therefore, a novel separation approach, the thermal online-elution was developed. The maximum capacity of an affinity column was 650 ng TNT or 10 µg/mL of column volume. To quantify the immobilization rate of proteins, a new method has been developed, because the usual protein determination methods were unsuitable. Therefore an HPLC separation method of Tyr and Phe was developed without prior derivatization. Two internal standard compounds, HTyr and FPhe, were used for calibration. The LOD was estimated to be 0.05 µM (~ 10 µg/L) for Tyr and Phe at 215 nm. The protein hydrolysis time was reduced from 22 h to 30 min using microwave technique. This procedure, that was termed aromatic amino acid analysis (AAAA), has been validated for protein determination of homogeneous samples with NIST-BSA. The LOD for proteins was calculated to be below 16 mg/L (~ 300 ng BSA absolute). The relative standard deviation, including the hydrolysis step, is 5%.