Thesis (PhD (Mechanical and Mechatronic Engineering))--University of Stellenbosch, 2003. / The thermal performance prediction of wet-cooling towers is critically analyzed and refined. Natural draft counterflow towers and mechanical draft counterflow and crossflow towers are considered. The Merkel, Poppe and e-NTU heat and mass transfer methods of analysis are derived from first principles, as these methods form the cornerstone of wet-cooling tower performance evaluation. The critical differences between these methods, when applied to fill performance analyses and cooling tower performance evaluations, are highlighted. The reasons for these differences are discussed with the aid of psychrometric charts. A new extended empirical relation for the loss coefficient of fills is proposed where the viscous and form drag effects are accounted for as well as the buoyancy, momentum and fill height effects. The empirical equation for the transfer characteristic of fills is extended to include the effects of fill height and the inlet water temperature. Empirical equations to predict the temperature inversion profile, height of the temperature inversion and the height from which air is drawn into the cooling tower are developed. The influence of temperature and humidity inversions on the performance of wet-cooling towers is subsequently investigated. A comprehensive analytical computer program is developed to predict and optimize the performance of wet-cooling towers. Computer programs are also developed to generate cooling tower performance curves, analyze fill performance test data and plot psychrometric charts.

In the last years multilevel preconditioners like BPX became more and more popular for solving second-order elliptic finite element discretizations by iterative methods. P. Oswald has adapted these methods for discretizations of the fourth order biharmonic problem by rectangular conforming Bogner-Fox-Schmidt elements and nonconforming Adini elements and has derived optimal estimates for the condition numbers of the preconditioned linear systems. In this paper we generalize the results from Oswald to the construction of BPX and Multilevel Diagonal Scaling (MDS-BPX) preconditioners for the elasticity problem of thin smooth shells of arbitrary forms where we use Koiter's equations of equilibrium for an homogeneous and isotropic thin shell, clamped on a part of its boundary and loaded by a resultant on its middle surface. We use the two discretizations mentioned above and the preconditioned conjugate gradient method as iterative method. The parallelization concept is based on a non-overlapping domain decomposition data structure. We describe the implementations of the multilevel preconditioners. Finally, we show numerical results for some classes of shells like plates, cylinders, and hyperboloids.

Made available in DSpace on 2014-10-09T12:55:30Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:07:16Z (GMT). No. of bitstreams: 0 / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Made available in DSpace on 2014-10-09T12:55:30Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T14:07:16Z (GMT). No. of bitstreams: 0 / Foi desenvolvida uma técnica de medida de nível em vasos de pressão usando sondas térmicas resfriadas internamente por um fluido e análise dos dados experimentais com Redes Neurais Artificiais (RNA´s). Esse novo conceito de sondas térmicas foi testado em uma Bancada Experimental para Testes de Sondas de Nível (BETSNI) com duas seções de testes, ST1 e ST2. Dois projetos distintos de sondas foram construídos: Sonda de Tubos Concêntricos e Sonda de Tubo U. Um Sistema de Aquisição de Dados (SAD) foi montado para registrar os dados experimentais. Testes foram realizados tanto para condições de nível nas seções de testes em estado estacionário quanto para transientes. Os dados experimentais de temperatura e de nível obtidos foram usados para compor tabelas de treinamento e de verificação usadas para implementar RNA´s no programa RETRO-05, que simula um Perceptron de Múltiplas Camadas com Retropropagação. As análises mostraram que a técnica pode ser aplicada para medir o nível em vasos de pressão. As análises mostraram ainda que a técnica é aplicável para um número menor de entradas de temperatura que o inicialmente previsto no projeto das sondas e é robusta, aplicando-se mesmo quando ocorre a perda de alguma informação de temperatura. Dados experimentais disponíveis na literatura referentes a uma sonda térmica aquecida eletricamente também foram usados nas análises com RNA´s, produzindo bons resultados. Os resultados das análises indicaram que a técnica é eficaz e robusta, podendo ser aprimorada e aplicada para medidas de nível em vasos de pressão. / Tese (Doutoramento) / IPEN/T / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

An approach to hybrid cooling technique is proposed using air jets which impinge on a triangular grooved surface with dry grooves and grooves containing water. One major application is for condensers of thermoelectric power plants. The heat and mass transfer analogy were successfully used to evaluate the simultaneous heat and mass transfer. Results showed that hybrid jet impingement produced high heat flux levels at low jet velocities and flow rates. Experimental results were used to characterize the resulting heat transfer under different conditions such as flow open area percentage, array orifices diameter and array to surface stand-off distance. The results have shown that jet impingement is capable of delivering high transfer rates with lower cooling cost rates compared to current industry conventional techniques. Water is efficiently used in hybrid jet impingement because evaporative energy is absorbed directly from the surface instead of cooling air to near wet-bulb temperature. / Master of Science / Array jet impingement cooling experiments were conducted on a triangular grooved surface with the surface at a constant temperature. Results showed that jet impingement can provide high transfer rates with lower rates of cooling cost in comparison to contemporary conventional techniques in the industry. Experiments on the triangular grooved surfaces were performed at dry and wet surface conditions. Under the dry conditions, the objective is to characterize the resulting heat transfer under varying operational conditions such as jet speed, array orifice diameter, array to surface stand-off distance, and flow open area percentage. Results from the triangular surface when dry showed less improvement in heat transfer than the rectangular grooved surface. A hybrid cooling technique approach was proposed and developed by using air jets impinging on a triangular grooved surface with the grooves containing water. The approach is being suggested and experimentally tested for its viability as an alternative to thermoelectric power plant cooling towers. Convection heat and mass transfer coefficients were experimentally measured for different wet coverage of the surface. Results showed that the hybrid jet impingement produced high heat flux levels at low jet velocities and flow rates. The highest heat transfer was consistently found with a 50% coverage of the surface. Hybrid jet impingement showed an improvement up to 500% in heat transfer as compared to jet impingement on a dry grooved surface.

Array jet impingement cooling experiments were performed on flat and grooved surfaces with the surface at a constant temperature. For the flat surface, power and temperature measurements were performed to obtain convection coefficients under a wide range of operating conditions such as jet speed, orifice to surface stand-of distance, and open area percentage. Cooling performance (CP) was calculated as the ratio between heat transfer and fan power. An empirical model was developed to predict jet impingement heat transfer taking into account the entrainment effects. Experimental results showed that jet impingement can provide high transfer rates with lower rates of cooling cost in comparison to contemporary conventional techniques in the industry. CP values over 279 were measured which are significantly higher than the standard values of 70 to 95 in current technology. The model enhanced prediction accuracy by taking into account the entrainment effects; an effect that is rarely considered in the literature. Experiments on the grooved surfaces were performed at dry and wet surface conditions. Under dry conditions, results showed 10%~55% improvement in heat transfer when compared to the flat surface. Improvement percentage tends to be higher at wider gaps between the array of orifices and the grooved surface. An improvement of 30%~40% was observed when increasing Re either by increasing orifice diameter or jet speed. Similar improvement was observed at higher flow open area percentages. No significant improvement in heat transfer resulted from decreasing the size of the grooves from 3.56mm to 2.54mm. Similarly, no noticeable change in heat transfer resulted from changing the relative position of the jets striking the surface at the top of the grooves to the bottom of the grooves. Deeper grooves with twice the depth gave statistically similar average heat transfer coefficients as shallower grooves. Under wet conditions, a hybrid cooling technique approach was proposed by using air jets impinging on a grooved surface with the grooves containing water. The approached is proposed and evaluated experimentally for its feasibility as an alternative for cooling towers of thermoelectric power plants. Convection heat and mass transfer coefficients were measured experimentally using the heat mass transfer analogy. Results showed that hybrid jet impingement provided high magnitudes of heat flux at low jet speeds and flow rates. High coefficients of performance CP > 3000, and heat fluxes > 8,000W/m2 were observed. Hybrid jet impingement showed 500% improvement as compared to jet impingement on a dry flat surface. CP values of hybrid jet impingement is 600% to 1,500% more as compared to performance of air-cooled condensers and wet cooling towers. Water use for hybrid jet impingement cooling is efficient since evaporation energy is absorbed from the surface directly instead of cooling air to near wet-bulb temperature. / PHD / This thesis explored the possibility of using air jets on the outside surface of a device that is used to condense steam. An experiment apparatus was used to imitate the conditions of steam condensation in the lab. A flat metallic surface was heated by placing an electric heater beneath it. The metallic surface was cooled using air jets coming out of orifices situated above the hot metallic surface. A fan, connected to an electric motor, was used to create the air jets. The amount of heat transfer was measured by measuring the electric power the heater consumed. This measured power was compared to the power needed to run the fan. The ratio of heat transfer to fan power is called the coefficient of performance CP. The CP values of more than 200 were obtained when air jets were used meaning that we need one kilowatt of mechanical power to remove 200 kilowatts of heat. This CP value is 300% more than the current technology used in the industry where CP ranges from 70 to 90. This means that we can build very efficient steam condensers for power plants. This type of condensers that uses air jets allows the power plant to be efficient and to be able to increase the amount of power generated without extra cost. Further enhancement of the CP can be achieved by making the hot surface grooved instead of flat with the grooves containing water. Air jets, coming out of orifices situated above the grooved surface, were used for cooling. The CP values of more than 3,000 were obtained when air jets were used with wet grooved surface. This CP values is 1,500% more than the current technology used in the industry. This type of condensers that uses air jets on wet grooves allows the power plant to be efficient and to be able to tremendously increase the amount of power generated without extra power and water costs.

abstract: Passive cooling techniques, specifically passive downdraft cooling (PDC), have proven to be a solution that can address issues associated with air conditioning (AC). Globally, over 100 buildings have integrated PDC in its different forms, most of which use direct evaporative cooling. Even though all surveyed buildings were energy efficient and cost-effective and most surveyed buildings were thermally comfortable, application of PDC remains limited. This study aims to advance performance of the single stage passive downdraft evaporative cooling tower (PDECT), and expand its applicability beyond the hot dry conditions where it is typically used, by designing and testing a multi-stage passive and hybrid downdraft cooling tower (PHDCT). Experimental evaluation on half-scale prototypes of these towers was conducted in Tempe, Arizona, during the hot dry and hot humid days of Summer, 2017. Ambient air dry-bulb temperatures ranged between 73.0°F with 82.9 percent coincident relative humidity, and 123.4°F with 7.8 percent coincident relative humidity. Cooling systems in both towers were operated simultaneously to evaluate performance under identical conditions. Results indicated that the hybrid tower outperformed the single stage tower under all ambient conditions and that towers site water consumption was at least 2 times lower than source water required by electric powered AC. Under hot dry conditions, the single stage tower produced average temperature drops of 35°F (5°F higher than what was reported in the literature), average air velocities of 200 fpm, and average cooling capacities of 4 tons. Furthermore, the hybrid tower produced average temperature drops of 45°F (50°F in certain operation modes), average air velocities of 160 fpm, and average cooling capacities exceeding 4 tons. Under hot humid conditions, temperature drops from the single stage tower were limited to the ambient air wet-bulb temperatures whereas drops continued beyond the wet-bulb in the hybrid tower, resulting in 60 percent decline in the former’s cooling capacity while maintaining the capacity of the latter. The outcomes from this study will act as an incentive for designers to consider incorporating PDC into their designs as a viable replacement/supplement to AC; thus, reducing the impact of the built environment on the natural environment. / Dissertation/Thesis / Doctoral Dissertation Architecture 2017

In the last years multilevel preconditioners like BPX became more and more popular for solving second-order elliptic finite element discretizations by iterative methods. P. Oswald has adapted these methods for discretizations of the fourth order biharmonic problem by rectangular conforming Bogner-Fox-Schmidt elements and nonconforming Adini elements and has derived optimal estimates for the condition numbers of the preconditioned linear systems. In this paper we generalize the results from Oswald to the construction of BPX and Multilevel Diagonal Scaling (MDS-BPX) preconditioners for the elasticity problem of thin smooth shells of arbitrary forms where we use Koiter's equations of equilibrium for an homogeneous and isotropic thin shell, clamped on a part of its boundary and loaded by a resultant on its middle surface. We use the two discretizations mentioned above and the preconditioned conjugate gradient method as iterative method. The parallelization concept is based on a non-overlapping domain decomposition data structure. We describe the implementations of the multilevel preconditioners. Finally, we show numerical results for some classes of shells like plates, cylinders, and hyperboloids.

M.Tech. (Department of Chemical Engineering, Faculty of Engineering and Technology), Vaal University of Technology. / In the present study, the removal of Ca2+ and Mg2+ from cooling tower water using Amberlite IR120 and Amberjet 1200 was studied by the application of one factor at a time method (OFAT) and response surface modelling (RSM). The effect of operational parameters such as contact time (min), pH, dosage (mL), concentration (mg/L) and temperature (K) were investigated using central composite design. The regeneration of the Amberlite IR120 and Amberjet were also studied. The purpose of the study was to apply OFAT and RSM to investigate and optimize the ion exchange operating parameters. Furthermore, the second-order empirical model that was developed, using the analysis of variance (ANOVA), presented a sufficient correlation to the ion exchange experimental data. The optimal ion exchange operating conditions for Amberlite IR120 and Amberjet 1200 were found to be: contact time was 120 min, dosage of 150mL, initial pH level of 2, concentration of 400mg/L and temperature of 343K. Regeneration of Amberlite IR120 and Amberjet 1200 using 0.5 M NaCl stripping solution initially showed an increase in % Ca2+ and Mg2+ removal, then a decrease in subsequent cycles. The correlation coefficients (R2) of Langmuir, Freudlich and Tempkin isotherms were found to range from 0.92 to 1 and this suggest that experimental data best described the models. However correlation coefficients (R2) for Dubinin–Radushkevich (D-R) model were found to range between 0.5 to 0.8 and this means that experimental data does not fit the model. Thermodynamic functions such as entropy (Δ𝑆𝑜), enthalpy (Δ𝐻𝑜) and change of free energy (Δ𝐺𝑜) were obtained from the gradient and intercepts of straight line graphs. The positive values of ΔG° were found meaning that the adsorption is not spontaneous and positive values of ΔH° were found meaning the endothermic type of adsorption which indicate the chances of physical adsorption.The correlation coefficient (R2) values of pseudo-first-order, pseudo-second-order and intraparticle models were found to range from 0.89 to 1 on both metals as shown in table 4.4. This observation clearly indicates that pseudo-first-order, pseudo-second-order and intraparticle diffusion models best describe the experimental data in the removal Ca2+ and Mg2+ from cooling tower water.